ATIS 0300247-2013 Operations Administration Maintenance and Provisioning (OAM&P) - Performance Management Functional Area Services and Information Model for Interfaces Between Oper.pdf

《ATIS 0300247-2013 Operations Administration Maintenance and Provisioning (OAM&P) - Performance Management Functional Area Services and Information Model for Interfaces Between Oper.pdf》由会员分享，可在线阅读，更多相关《ATIS 0300247-2013 Operations Administration Maintenance and Provisioning (OAM&P) - Performance Management Functional Area Services and Information Model for Interfaces Between Oper.pdf（85页珍藏版）》请在麦多课文档分享上搜索。

1、 AMERICAN NATIONAL STANDARD FOR TELECOMMUNICATIONS ATIS-0300247.2013 OPERATIONS, ADMINISTRATION, MAINTENANCE, AND PROVISIONING (OAM their existence does not in any respect preclude anyone, whether he has approved the standards or not, from manufacturing, marketing, purchasing, or using products, pro

2、cesses, or procedures not conforming to the standards. The American National Standards Institute does not develop standards and will in no circumstances give an interpretation of any American National Standard. Moreover, no person shall have the right or authority to issue an interpretation of an Am

3、erican National Standard in the name of the American National Standards Institute. Requests for interpretations should be addressed to the secretariat or sponsor whose name appears on the title page of this standard. CAUTION NOTICE: This American National Standard may be revised or withdrawn at any

4、time. The procedures of the American National Standards Institute require that action be taken periodically to reaffirm, revise, or withdraw this standard. Purchasers of American National Standards may receive current information on all standards by calling or writing the American National Standards

5、 Institute. Notice of Disclaimer CHARACTERIZED BY cVPkg, eSPkg, sESPkg, dS1LineTTPSinkNECurrentDataPkg PACKAGE BEHAVIOUR dS1LineTTPSinkNECurrentDataBehaviour BEHAVIOUR DEFINED AS “The dS1LineTTPSinkNECurrentData object class is a class of managed support object that is used to monitor performance pa

6、rameter aspects of DS1 Line TTPs. This object monitors only Near-end line per-formance parameters. Instances of this object class may be created either by a managing system or automatically by a man-aged system. These are contained in the observed trail termination point object at the DS1 rate. Crit

7、eria for the inclusion of the conditional packages as represented in the PRESENT IF clause for each package is derived from the functional requirements for the corresponding performance measure-ment parameters in ATIS-0300231.” ; CONDITIONAL PACKAGES ATIS-0300247.2013 6 lOSSPkg PRESENT IF “an instan

8、ce supports it.”; REGISTERED AS pMObjectClass 9; 7.1.2 DS1 Line TTP Sink Far End Current Data dS1LineTTPSinkFECurrentData MANAGED OBJECT CLASS DERIVED FROM “Recommendation Q.822:1994”:currentData; CHARACTERIZED BY eSFEPkg, dS1LineTTPSinkFECurrentDataPkg PACKAGE BEHAVIOUR dS1LineTTPSinkFECurrentDataB

9、ehaviour BEHAVIOUR DEFINED AS “The dS1LineTTPSinkFECurrentData object class is a class of managed support object that is used to monitor performance parameter aspects of DS1 Line TTPs. This object is only instantiated if the framing format is DS1 ESF. This object monitors only Far-end line performan

10、ce parameters, based on anoma-lies and defects observed at the far end of the DS1 ESF path and reported back through the ESF data link. Instances of this object class may be created either by a managing system or automatically by a man-aged system. These are contained in the observed trail terminati

11、on point object at the DS1 rate. Criteria for the creation of this object is derived from the functional requirements for the corresponding performance measurement parameters in ATIS-0300231.” ; REGISTERED AS pMObjectClass 10; 7.1.3 DS1 Line TTP Sink Near End History Data dS1LineTTPSinkNEHistoryData

12、 MANAGED OBJECT CLASS DERIVED FROM “Recommendation Q.822:1994”:historyData; CHARACTERIZED BY cVHistoryPkg, eSHistoryPkg, sESHistoryPkg, dS1LineTTPSinkNEHistoryDataPkg PACKAGE BEHAVIOUR dS1LineTTPSinkNEHistoryDataBehaviour BEHAVIOUR ATIS-0300247.2013 7 DEFINED AS “Instances of this object class are u

13、sed to store the observed measurements of the observed dS1LineTTPSinkCurrentData object at the end of an observation interval. Criteria for the inclusion of the conditional packages as represented in the PRESENT IF clause for each package is derived from the functional requirements for the correspon

14、ding performance measure-ment parameters in ATIS-0300231.” ; CONDITIONAL PACKAGES lOSSHistoryPkg PRESENT IF “an instance supports it.”; REGISTERED AS pMObjectClass 11; 7.1.4 DS1 Line TTP Sink Far End History Data dS1LineTTPSinkFEHistoryData MANAGED OBJECT CLASS DERIVED FROM “Recommendation Q.822:199

15、4”:historyData; CHARACTERIZED BY eSFEHistoryPkg, dS1LineTTPSinkFEHistoryDataPkg PACKAGE BEHAVIOUR dS1LineTTPSinkFEHistoryDataBehaviour BEHAVIOUR DEFINED AS “Instances of this object class are used to store the observed measurements of the observed dS1LineTTPSinkCurrentData object at the end of an ob

16、servation interval. Criteria for the creation of this object is derived from the functional requirements for the corresponding performance measurement parameters in ATIS-0300231.” ; REGISTERED AS pMObjectClass 12; 7.1.5 DS1 Path TTP Sink Near End Current Data dS1PathTTPSinkNECurrentData MANAGED OBJE

17、CT CLASS DERIVED FROM “Recommendation Q.822:1994”:currentData; CHARACTERIZED BY cVPkg, eSPkg, sASPkg, ATIS-0300247.2013 8 sESPkg, uASPkg, dS1PathTTPSinkNECurrentDataPkg PACKAGE BEHAVIOUR dS1PathTTPSinkNECurrentDataBehaviour BEHAVIOUR DEFINED AS “The dS1PathTTPSinkNECurrentData object class is a clas

18、s of managed support object that is used to monitor performance aspects of DS1 path TTPs. This object monitors only Near-end path performance parameters. Instances of this object class may be created either by a managing system or automatically by a man-aged system. These are contained in the observ

19、ed trail termination point object at the DS1 rate. Criteria for the inclusion of the conditional packages as represented in the PRESENT IF clause for each package is derived from the functional requirements for the corresponding performance measure-ment parameters in ATIS-0300231. To support custome

20、r/network sectionalization, the TTPSink must be capable of detecting the AIS-CI signal and/or either the SPRM or NPRM messages from a Network Interface Unit that mediates a DS1 originating/terminating at a customer installation as specified in ATIS-0300231” ; CONDITIONAL PACKAGES aISSPkg PRESENT IF

21、“an instance supports it.”, aISSCIPkg PRESENT IF “an instance supports it.”, cSSPkg PRESENT IF “and only if controlled slip monitoring is supported.”, eSAPkg PRESENT IF “the framing format is DS1 ESF and an instance supports it.”, eSBPkg PRESENT IF “the framing format is DS1 ESF and an instance supp

22、orts it.”, eSNPPkg PRESENT IF “customer/network sectionalization is supported.”, sESNPPkg PRESENT IF “customer/network sectionalization is supported.”, uASNPPkg PRESENT IF “customer/network sectionalization is supported.”; REGISTERED AS pMObjectClass 13; ATIS-0300247.2013 9 7.1.6 DS1 Path TTP Sink F

23、ar End Current Data dS1PathTTPSinkFECurrentData MANAGED OBJECT CLASS DERIVED FROM “Recommendation Q.822:1994”:currentData; CHARACTERIZED BY cVFEPkg, eSFEPkg, sEFSFEPkg, sESFEPkg, uASFEPkg, dS1PathTTPSinkFECurrentDataPkg PACKAGE BEHAVIOUR dS1PathTTPSinkFECurrentDataBehaviour BEHAVIOUR DEFINED AS “The

24、 dS1PathTTPSinkFECurrentData object class is a class of managed support object that is used to monitor performance aspects of DS1 path TTPs. This object is only instantiated if the framing format is DS1 ESF. This object monitors only Far-end path performance parameters, based on anomalies and defect

25、s observed at the far end of the DS1 ESF path and reported back through the ESF data link. Instances of this object class may be created either by a managing system or automatically by a managed system. These are contained in the observed trail termination point object at the DS1 rate. Criteria for

26、the inclusion of the conditional packages as represented in the PRESENT IF clause for each package is derived from the functional requirements for the corresponding performance measurement parameters in ATIS-0300231. To support customer/network sectionalization, the TTPSink must be capable of detect

27、ing the RAI-CI signal and/or either the SPRM or NPRM messages from a Network Interface Unit that medi-ates a DS1 originating/terminating at a customer installation as specified in ATIS-0300231” ; CONDITIONAL PACKAGES cSSFEPkg PRESENT IF “and only if controlled slip monitoring are supported.”, eSAFEP

28、kg PRESENT IF “an instance supports it.”, eSBFEPkg PRESENT IF “an instance supports it.”, eSNPFEPkg PRESENT IF “customer/network sectionalization is supported”, sESNPFEPkg ATIS-0300247.2013 10 PRESENT IF “customer/network sectionalization is supported.”, uASNPFEPkg PRESENT IF “customer/network secti

29、onalization is supported.”; REGISTERED AS pMObjectClass 14; 7.1.7 DS1 Path TTP Sink Near End History Data dS1PathTTPSinkNEHistoryData MANAGED OBJECT CLASS DERIVED FROM “Recommendation Q.822:1994”:historyData; CHARACTERIZED BY cVHistoryPkg, eSHistoryPkg, sASHistoryPkg, sESHistoryPkg, uASHistoryPkg, d

30、S1PathTTPSinkNEHistoryDataPkg PACKAGE BEHAVIOUR dS1PathTTPSinkNEHistoryDataBehaviour BEHAVIOUR DEFINED AS “Instances of this object class are used to store the observed measurements of the observed dS1PathTTPSinkNECurrentData object at the end of an observation interval. Criteria for the inclusion o

31、f the conditional packages as represented in the PRESENT IF clause for each package is derived from the functional requirements for the corresponding performance measurement parameters in ATIS-0300231. To support customer/network sectionalization, the TTPSink must be capable of detecting the AIS-CI

32、signal and/or either the SPRM or NPRM messages from a Network Interface Unit that medi-ates a DS1 originating/terminating at a customer installation as specified in ATIS-0300231.” ; CONDITIONAL PACKAGES aISSHistoryPkg PRESENT IF “an instance supports it.”, aISSCIHistoryPkg PRESENT IF “an instance su

33、pports it.”, cSSHistoryPkg PRESENT IF “and only if controlled slip monitoring is supported.”, ATIS-0300247.2013 11 eSAHistoryPkg PRESENT IF “the framing format is DS1 ESF and an instance supports it.”, eSBHistoryPkg PRESENT IF “the framing format is DS1 ESF and an instance supports it.”, eSNPHistory

34、Pkg PRESENT IF “customer/network sectionalization is supported.”, sESNPHistoryPkg PRESENT IF “customer/network sectionalization is supported.”, uASNPHistoryPkg PRESENT IF “customer/network sectionalization is supported.”; REGISTERED AS pMObjectClass 15; 7.1.8 DS1 Path TTP Sink Far End History Data d

35、S1PathTTPSinkFEHistoryData MANAGED OBJECT CLASS DERIVED FROM “Recommendation Q.822:1994”:historyData; CHARACTERIZED BY cVFEHistoryPkg, eSFEHistoryPkg, sEFSFEHistoryPkg, sESFEHistoryPkg, uASFEHistoryPkg, dS1PathTTPSinkFEHistoryDataPkg PACKAGE BEHAVIOUR dS1PathTTPSinkFEHistoryDataBehaviour BEHAVIOUR D

36、EFINED AS “Instances of this object class are used to store the observed measurements of the observed dS1PathTTPSinkFECurrentData object at the end of an observation interval. Criteria for the inclusion of the conditional packages as represented in the PRESENT IF clause for each package is derived f

37、rom the functional requirements for the corresponding performance measurement parameters in ATIS-0300231. To support customer/network sectionalization the TTPSink must be capable of detecting the RAI-CI signal and/or either the SPRM or NPRM messages from a Network Interface Unit that medi-ates a DS1

38、 originating/terminating at a customer installation as specified in ATIS-0300231.” ; CONDITIONAL PACKAGES cSSFEHistoryPkg PRESENT IF “and only if controlled slip monitoring are supported.”, eSAFEHistoryPkg ATIS-0300247.2013 12 PRESENT IF “an instance supports it.”, eSBFEHistoryPkg PRESENT IF “an ins

39、tance supports it.”, eSNPFEHistoryPkg PRESENT IF “customer/network sectionalization is supported.”, sESNPFEHistoryPkg PRESENT IF “customer/network sectionalization is supported.”, uASNPFEHistoryPkg PRESENT IF “customer/network sectionalization is supported.”; REGISTERED AS pMObjectClass 16; 7.1.9 DS

40、3 Line TTP Sink Near End Current Data dS3LineTTPSinkNECurrentData MANAGED OBJECT CLASS DERIVED FROM “Recommendation Q.822:1994”:currentData; CHARACTERIZED BY eSPkg, sESPkg, dS3LineTTPSinkNECurrentDataPkg PACKAGE BEHAVIOUR dS3LineTTPSinkNECurrentDataBehaviour BEHAVIOUR DEFINED AS “The dS3LineTTPSinkN

41、ECurrentData object class is a class of managed support object that is used to monitor performance parameter aspects of DS3 Line TTPs. This object monitors only Near-end line performance parameters. Instances of this object class may be created either by a managing system or automatically by a manag

42、ed system, and are contained in the observed trail termination point object at the DS3 rate. Criteria for the inclusion of the conditional packages as represented in the PRESENT IF clause for each package is derived from the functional requirements for the corresponding performance measurement param

43、eters in ATIS-0300231.” ; CONDITIONAL PACKAGES cVPkg PRESENT IF “an instance supports it.”, eSAPkg ATIS-0300247.2013 13 PRESENT IF “an instance supports it.”, eSBPkg PRESENT IF “an instance supports it.”, LOSSPkg PRESENT IF “an instance supports it.”; REGISTERED AS pMObjectClass 17; 7.1.10 DS3 Line

44、TTP Sink Near End History Data dS3LineTTPSinkNEHistoryData MANAGED OBJECT CLASS DERIVED FROM “Recommendation Q.822:1994”:historyData; CHARACTERIZED BY eSHistoryPkg, sESHistoryPkg, dS3LineTTPSinkNEHistoryDataPkg PACKAGE BEHAVIOUR dS3LineTTPSinkNEHistoryDataBehaviour BEHAVIOUR DEFINED AS “Instances of

45、 this object class are used to store the observed measurements of the observed dS3LineTTPSinkNECurrentData object at the end of an observation interval. Criteria for the inclusion of the conditional packages as represented in the PRESENT IF clause for each package is derived from the functional requ

46、irements for the corresponding performance measurement parameters in ATIS-0300231.” ; CONDITIONAL PACKAGES cVHistoryPkg PRESENT IF “an instance supports it.”, eSAHistoryPkg PRESENT IF “an instance supports it.”, eSBHistoryPkg PRESENT IF “an instance supports it.”, lOSSHistoryPkg PRESENT IF “an insta

47、nce supports it.”; REGISTERED AS pMObjectClass 18; ATIS-0300247.2013 14 7.1.11 DS3 Path TTP Sink Near End Current Data dS3PathTTPSinkNECurrentData MANAGED OBJECT CLASS DERIVED FROM “Recommendation Q.822:1994”:currentData; CHARACTERIZED BY dS3PathTTPSinkNECurrentDataPkg PACKAGE BEHAVIOUR dS3PathTTPSi

48、nkNECurrentDataBehaviour BEHAVIOUR DEFINED AS “The dS3PathTTPSinkNECurrentData object class is a class of managed support object that is used to monitor performance aspects of DS3 path TTPs. This object monitors only Near-end path performance parameters. Instances of this object class may be created

49、 either by a managing system or automatically by a managed system and are contained in the observed trail termination point object at the DS3 rate. Criteria for the inclusion of the conditional packages as represented in the PRESENT IF clause for each package is derived from the functional requirements for the corresponding performance measurement parameters in ATIS-0300231.” ; CONDITIONAL PACKAGES aISSPkg PRESENT IF “an instance supports it.”, cVCPPkg PRESENT IF “and only if the C-bit Parity Application is supported.