BS EN 60603-6-1998 Connectors for frequencies below 3 MHz for use with printed boards - Edge-socket connectors and printed board connectors with 2 54 mm (0 1 in) contact spacing fom.pdf

《BS EN 60603-6-1998 Connectors for frequencies below 3 MHz for use with printed boards - Edge-socket connectors and printed board connectors with 2 54 mm (0 1 in) contact spacing fom.pdf》由会员分享，可在线阅读，更多相关《BS EN 60603-6-1998 Connectors for frequencies below 3 MHz for use with printed boards - Edge-socket connectors and printed board connectors with 2 54 mm (0 1 in) contact spacing fom.pdf（44页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 60603-6:1998 IEC60603-6: 1987 Connectors for frequencies below3MHz for use with printed boards Part 6: Edge-socket connectors and printed board connectors with2,54mm(0,1in) contact spacing for single or double-sided printed boards of1,6mm (0,063in) nominal thickness The Europe

2、an Standard EN60603-6:1998 has the status of a British Standard ICS 31.220.10BSEN60603-6:1998 This British Standard, having been prepared under the directionof the Electrotechnical Sector Board, was published underthe authority of the Standards Board and comes intoeffect on 15 May1998 BSI05-1999 ISB

3、N 0 580 29299 1 National foreword This British Standard is the English language version of EN60603-6:1998. It is identical with IEC60603-6:1987. The UK participation in its preparation was entrusted by Technical Committee EPL/48, Electromechanical components for electronic equipment, to Subcommittee

4、 EPL/48/2, Connectors for electronic equipment, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related interna

5、tional and European developments and promulgate them in the UK. A list of organizations represented on this subcommittee can be obtained on request to its secretary. From 1 January 1997, all IEC publications have the number60000 added to the old number. For instance, IEC27-1 has been renumbered as I

6、EC60027-1. For a period of time during the change over from one numbering system to the other, publications may contain identifiers from both systems. Cross-references Attention is drawn to the fact that CEN and CENELEC standards normally include an annex which lists normative references to internat

7、ional publications with their corresponding European publications. The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by us

8、ing the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunit

9、y from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theEN title page, pages2 to38 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendme

10、nt table on the inside front cover. Amendments issued since publication Amd. No. Date CommentsBSEN60603-6:1998 BSI 05-1999 i Contents Page National foreword Inside front cover Foreword 2 Text of EN60603-6 3ii blankEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 60603-6 February 1998 ICS 31.220.

11、10 Descriptors: Electronic components, electric connectors, printed-circuit cards, connector plugs, designation, dimensions, assembling, couplings, tests, standard gauges, characteristics English version Connectors for frequencies below3MHz for use with printed boards Part6: Edge-socket connectors a

12、nd printed-board connectors with2,54mm(0,1in) contactspacingforsingle or double-sided printed boardsof1,6mm(0,063in)nominalthickness (IEC 60603-6:1987) Connecteurs pour frquences infrieures 3MHz pour utilisation avec cartes imprimes Partie6: Connecteurs encartables et pour cartes imprimes cartement

13、des contacts de2,54mm (0,1in) pour cartes imprimes simple ou double face, ayant une paisseur nominale de 1,6mm (0,063in) (CEI60603-6:1987) Steckverbinder fr gedruckte Schaltungen fr Frequenzen unter3MHz Teil6: Direkte Steckverbinder und Steckverbinder fr gedruckte Schaltungen mit2,54mm (0,1in) Konta

14、ktabstand fr ein- oder beidseitig beschichtete Leiterplatten mit1,6mm (0,063in) Nenndicke (IEC60603-6:1987) This European Standard was approved by CENELEC on 1998-01-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this Europ

15、ean Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (Engl

16、ish, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria,

17、Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europ

18、isches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels 1998 CENELEC All rights of exploitation in any form and by any means reserved worldwidefor CENELEC members. Ref. No. EN 60603-6:1998 EEN60603-6:1998 2 BSI 05-1999 Foreword The text of the Internation

19、al Standard IEC60603-6:1987, prepared by SC48B, Connectors, of IEC TC48, Electromechanical components and mechanical structures for electronic equipment, was submitted to the formal vote and was approved by CENELEC as EN60603-6 on1998-01-01 without any modification. The following dates were fixed: A

20、nnexes designated “normative” are part of the body of the standard. In this standard, Annex ZA is normative. Annex ZA has been added by CENELEC. Endorsement notice The text of the International Standard IEC60603-6:1987 was approved by CENELEC as a European Standard without any modification. Contents

21、 Page Foreword 2 1 Scope 3 2 IEC type designation 3 3 Common features 5 4 Dimensions 8 5 Gauges 24 6 Characteristics 28 7 Test schedule 29 Annex ZA (normative) Normative references tointernational publications with theircorresponding European publications 38 latest date by which the EN has to be imp

22、lemented at national level by publication of an identical national standard or by endorsement (dop) 1998-12-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 1998-12-01EN60603-6:1998 BSI 05-1999 3 1 Scope This standard covers a range of connectors with

23、2.54mm (0.1in) contact spacing intended to connect a single or double-sided printed board to another printed board or wires. Two kinds are available: Edge-socket connector A connector with female contacts intended to mate with edge-board contacts and with printed-board connectors having male contact

24、s. Edge-socket connectors are available with: solder terminations for wire; solder terminations for board mounting; wrap terminations. Printed-board connector A connector having male contacts which when mounted on a printed board replaces the edge-board contacts. Printed-board connectors are provide

25、d with solder terminations for single or double-sided boards of1.6mm(0.063in) nominal thickness. An edge-socket connector mated with a printed-board connector is referred to as a two-part connector in this standard. The mandatory method of locating is by means of a guide key which replaces an opposi

26、te pair of contacts, and one such key is provided per connector (see also Sub-clause4.5) This standard shall be used in conjunction with the following IEC publications: 2 IEC type designation Nos. 50 (581)(1978):International Electrotechnical Vocabulary, Chapter581: Electromechanical Components for

27、Electronic Equipment 603-1 (1981): Connectors for Frequencies Below3MHz for Use with Printed Boards, Part1:General Rules and Guide for the Preparation of Detail Specifications. 512-2 (1976): Electromechanical Components for Electronic Equipment; Basic Testing Procedures and Measuring Methods, Part2:

28、 General Examination, Electrical Continuity and Contact Resistance Tests, Insulation Tests and Voltage Stress Tests. 512-3 (1976): Part3: Current-carrying Capacity Tests. 512-6 (1984): Part6: Climatic Tests and Soldering Tests. 512-7 (1978): Part7: Mechanical Operating Tests and Sealing Tests. Amend

29、ment No. 1 (1983).EN60603-6:1998 4 BSI 05-1999 No. of detail specification/IEC: 603-6 IEC Style: As shown in Clauses3 and4 of this standard. Number of ways: Digits denoting the number of contact locations along one side of the connector. Maximum85 for Styles1,2,3 and5, and80 for Style4. Single or do

30、uble-sided and active contact row: A = single-sided, side A active, single row of terminations B = single-sided, side B active, single row of terminations E = single-sided, side A active, double row of terminations F = single-sided, side B active, double row of terminations D = double-sided, both si

31、des active Termination style: S = solder terminations for wire B = solder terminations for printed board W = wrap terminations T = through-board solder, short termination L = through-board solder, long termination X = through-board solder, extra long termination Contact finish: A = gold alloy Contac

32、t removal/replacement system: A = rear release/front removable/replaceable contacts B = rear release/rear removable/replaceable contacts C = front release/front removable/replaceable contacts D = front release/rear removable/replaceable contacts Variant: Digits identifying individual connector, part

33、s and associated tools for replacement purposes. Example of type designation: 603-6 IEC A 80 B W A C XXEN60603-6:1998 BSI 05-1999 5 3 Common features 3.1 Perspective views 3.1.1 Edge-socket connectorEN60603-6:1998 6 BSI 05-1999 3.1.2 Printed-board connectorEN60603-6:1998 BSI 05-1999 7 3.1.3 Values R

34、eference letter Legend a 1 Pitch of terminations of printed-board connector a 2 Pitch of contacts of edge-socket connector b 2 Distance between two rows C 1 Maximum overall length of printed-board connector C 2 C 3 Maximum overall length of edge-socket connector C 4 D Maximum overall width of edge-s

35、ocket connector H 1 Distance between mating face of printed-board connector and board M 2 M 3 Distance between mounting plane of edge-socket connector and bottom of board slot M 4 W Minimum length of mounting cut-out X Distance between fixing holes of edge-socket connector Z Minimum width of mountin

36、g cut-out Reference letter Printed-board connector Edge-socket connector Edge-socket connector metal feet Edge-socket connector closed ends Style5 Styles1 and2 Style3 Style4 C 1max. 2.54 n+0.43 (0.1n +0.017) C 2max. 2.54 n+6 (0.1n+0.236) C 3max. 2.54 n +30 (0.1n+1.18) C 4max. 2.54n+29.8 (0.1n+1.17)

37、D max. 10 (0.394) 10,4 (0.41) 10,4 (0.41) 10,4 (0.41) H 1 13.9/14.5 (0.55/0.57) M 2Style1 4.24/6.0 (0.167/0.236) M 2Style2 6.0/7.5 (0.236/0.295) M 3 , M 4 7.3/8.3 (0.29/0.33) W See page20 X 25.4n +16.2 (0.1 n+0.64) 25.4n+16.2 (0.1 n+0.64) Z min. 11 (0.433) 11 (0.433) 11 (0.433) a 1 2.54 (0.1) 2.54 (

38、0.1) 2.54 (0.1) 2.54 (0.1) a 2 2.54 (0.1) 2.54 (0.1) 2.54 (0.1) 2.54 (0.1) b 2 5.08 (0.2) 5.08 (0.2) 5.08 (0.2) 5.08 (0.2) NOTE 1n =number of contact positions along one side of connector. NOTE 2Dimensions in millimetres (inch dimensions in parentheses).EN60603-6:1998 8 BSI 05-1999 4 Dimensions 4.1

39、General Dimensions in millimetres are original. Drawings are shown in third angle projection. The shape of the connectors may deviate from those given in the following drawings as long as the specified dimensions are not influenced. 4.2 Connectors 4.2.1 Edge-socket connector Styles 1 and 2, open-end

40、ed. NOTE 1This tolerance should lie within dimensions e 2 . NOTE 2This measurement should be made with the component mounted in the normal manner. NOTE 3Dimensions j 2should be effective within card slot engagement area. NOTE 4Replacement guide keys and contacts should be identical to the originals.

41、 NOTE 5Row identification A and B is mandatory. Numerical marking is typical.EN60603-6:1998 BSI 05-1999 9 Dimension mm in A 2max. 16.3 0.642 B 2 9.3/7.8 0.37/0.31 C 2max. 2.54n+6 0.1n+0.236 F 2max. 10.4 0.41 G 2 (n1) 2.54 (n1) 0.1 M 2style1 4.24/6.0 0.167/0.236 M 2style2 6.0/7.5 0.236/0.295 a 2 2.54

42、 0.1 b 2 5.08 0.2 c 2min. 1.85 0.07 d 2min. 3.10 0.12 e 2 4.3/5.0 0.17/0.20 f 2 5.05/5.20 0.199/0.205 g 2 See page 8 h 2min. 0.5 0.02 j 2 1.58/1.52 0.062/0.060 NOTEn =number of contact positions along one side of connector (maximum permissible=85).EN60603-6:1998 10 BSI 05-1999 4.2.2 Edge-socket conn

43、ector, open-ended with metal mounting feet, Style3 NOTE 1This tolerance zone should lie within dimension M 3 . NOTE 2These measurements should be made with the components mounted in the normal manner. NOTE 3This dimension should be effective within card slot engagement area. NOTE 4Replacement contac

44、ts and guide keys should be identical to the originals. NOTE 5Row identification A and B is mandatory. Numerical marking is typical.EN60603-6:1998 BSI 05-1999 11 Dimension mm in A 3max. 17.6 0.69 B 3 9.3/7.8 0.37/0.31 C 3max. 2.54n+30 0.1n+1.81 D 3min. 3.10 0.12 D max. 10.4 0.41 G 3 (n 1) 2.54 (n1)

45、0.1 L 3max. 2.54n+10.1 0.1n+0.40 M 3 7.3/8.3 0.29/0.33 X 2.54n+16.2 0.1n+0.64 a 3 2.54 0.1 b 3 5.08 0.2 c 3min. 1.85 0.07 d 3min. 3.15 0.12 g 3 See page10 h 3min. 0.5 0.02 j 3 1.58/1.52 0.062/0.060 NOTEn =number of contact positions along one side of connector (maximum permissible = 85).EN60603-6:19

46、98 12 BSI 05-1999 4.2.3 Edge-socket connector, closed ends, Style4 NOTE 1This tolerance zone should lie within dimension M 4 . NOTE 2These measurements should be made with the components mounted in the normal manner. NOTE 3This dimension should be effective within card slot engagement area. NOTE 4Re

47、placement contacts and guide keys should be identical to the originals. NOTE 5Row identification A and B is mandatory. Numerical marking is typical.EN60603-6:1998 BSI 05-1999 13 Dimension mm in A 4max. 17.6 0.69 B 4 9.3/7.8 0.37/0.31 C 4max. 2.54n+29.8 0.1n+1.17 D 4min. 3.10 0.12 E 4 1.1/1.2 0.043/0

48、.047 D max. 10.4 0.41 G 4 (n 1) 2.54 (n1) 0.1 L 4max. 2.54n+10.1 0.1n+0.40 N 4 (2.54+0.5) (0.1n+0.002) X 2.54n +16.2 0.1n+0.64 a 4 2.54 0.1 b 4 5.08 0.2 C 4min. 1.85 0.07 d 4min. 3.40 0.13 f 4 g 4 See page12 h 4min. 0.5 0.02 j 4 1.58/1.52 0.062/0.060 NOTEn =number of contact positions along one side

49、 of connector (maximum permissible=80).0.4 + 00.016 + 0EN60603-6:1998 14 BSI 05-1999 4.2.4 Printed-board connector, Style5 NOTE 1Two pairs of retaining clamps should be supplied with connectors of size up to30 way. Three pairs of retaining clamps should be supplied with connectors from31 way to max. size. NOTE 2Positions of guide slots should be specified by the user (polarizing slots only if required).EN60603-6:1998 BSI 05-1999 15 Dimension mm in A 1max. 2