ASTM F2030-2000 Standard Specification for Paintball Cylinder Burst Disk Assemblies《彩弹球柱体防爆盘组件评估的标准规范》.pdf

《ASTM F2030-2000 Standard Specification for Paintball Cylinder Burst Disk Assemblies《彩弹球柱体防爆盘组件评估的标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM F2030-2000 Standard Specification for Paintball Cylinder Burst Disk Assemblies《彩弹球柱体防爆盘组件评估的标准规范》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F 2030 00An American National StandardStandard Specification forPaintball Cylinder Burst Disk Assemblies1This standard is issued under the fixed designation F 2030; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the y

2、ear of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers burst disk assemblies forpaintball marker propellant sources their application and i

3、n-stallation requirements.1.2 The values stated in SI units are to be regarded asstandard. The values given in parentheses are for informationonly.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this sta

4、ndard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 Code of Federal Regulations:2DOT 49 CFR 1734d2.2 CGA Standard:3CGA S-1-13. Materials and Manufacture3.1 The materials and processes used to m

5、anufacture theburst disk assembly shall result in items with mechanicalstrength sufficient to pass the applicable burst pressure tests.Materials used shall be corrosion resistant, chemically compat-ible with the propellant used and shall not promote galvanicaction. Rupture disks shall be manufacture

6、d and tested inaccordance with DOT 49 CFR 1734d and CGA S-1-1.3.2 The burst disk assembly and related port features shallbe free of burrs and sharp edges.4. Performance4.1 Burst disk assemblies intended for use with a servicepressure of 12 410 kPa (1800 psi) shall rupture at not less than18 615 kPa

7、(2700 psi) and no more than 20 684 kPa (3000 psi)at a temperature of 71.1C (160F). At a temperature of 15.6C(60F) the same burst disk shall rupture at not less than 19 822kPa (2875 psi) and no more than 21 890 kPa (3175 psi).4.2 The relief hole in the burst disk assembly shall providefor flow to ade

8、quately vent the cylinder as specified in CGAS-1-1.4.3 The rupture disk and seal shall be permanently retainedon the plug to provide proper alignment and assembly.5. Marking5.1 The burst disk assembly shall be marked with itsnominal burst pressure. The locations suitable for this markingare shown in

9、 Fig. 1. Markings shall appear in the U.S.Customary System of Units. A nominal burst pressure of20 684 kPa (3000 psi) may appear as 3K or 3000.5.2 The burst disk shall be marked with manufacturer codeand rated burst pressure.6. Physical Envelope, Burst Disk Assembly6.1 The burst disk assembly shall

10、conform to the physicalenvelope described in Fig. 1.7. Physical Envelope, Burst Disk Port7.1 The burst disk port shall conform to the physicalenvelope described in Fig. 2.8. Installation8.1 Prior to installation the mating port and the burst diskassembly shall be inspected to confirm compliance with

11、physical envelope requirements, cleanliness, and general suit-ability for use.8.2 It is recommended that the manufacturer supply instal-lation instructions for their burst disk assemblies.8.3 Unless instructed to do otherwise by the manufacturer,install the burst disk assembly into its mating port b

12、y threadingto a torque of 10 500 6 875 Nm (60 6 5 in. lb).9. Keywords9.1 burst disk; paintball marker; propellant1This specification is under the jurisdiction of ASTM Committee F08 on SportsEquipment and Facilities and is the direct responsibility of Subcommittee F08.24 onPaintball and Equipment.Cur

13、rent edition approved June 10, 2000. Published August 2000.2Code of Federal Regulations, available from U.S. Government Printing Office,Washington, DC 20402.3Available from Compressed Gas Assoc., Inc., 1725 Jefferson Davis Highway,Suite 1004, Arlington, VA 222024102.1Copyright ASTM International, 10

14、0 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the v

15、alidity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your c

16、omments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments ha

17、ve not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).FIG. 1 Burst Disk AssemblyFIG. 2 Burst Disk PortF 20302