ASTM F2003-2002(2015) Standard Practice for Accelerated Aging of Ultra-High Molecular Weight Polyethylene after Gamma Irradiation in Air《空气中伽马辐照后超高分子量聚乙烯加速老化的标准实施规程》.pdf

《ASTM F2003-2002(2015) Standard Practice for Accelerated Aging of Ultra-High Molecular Weight Polyethylene after Gamma Irradiation in Air《空气中伽马辐照后超高分子量聚乙烯加速老化的标准实施规程》.pdf》由会员分享，可在线阅读，更多相关《ASTM F2003-2002(2015) Standard Practice for Accelerated Aging of Ultra-High Molecular Weight Polyethylene after Gamma Irradiation in Air《空气中伽马辐照后超高分子量聚乙烯加速老化的标准实施规程》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F2003 02 (Reapproved 2015)Standard Practice forAccelerated Aging of Ultra-High Molecular WeightPolyethylene after Gamma Irradiation in Air1This standard is issued under the fixed designation F2003; the number immediately following the designation indicates the year oforiginal adoption o

2、r, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 It is the intent of this practice to permit an investigatorto evaluate the oxi

3、dative stability of UHMWPE materials as afunction of processing and sterilization method. This practicedescribes a laboratory procedure for accelerated aging ofultra-high molecular weight polyethylene (UHMWPE) speci-mens and components for total joint prostheses. The UHM-WPE is aged at elevated temp

4、erature and at elevated oxygenpressure, to accelerate oxidation of the material and therebyallow for the evaluation of its long-term chemical and me-chanical stability.1.2 Although the accelerated-aging method described bythis practice will permit an investigator to compare theoxidative stability of

5、 different UHMWPE materials, it isrecognized that this method may not precisely simulate thedegradative mechanisms for an implant during real-time shelfaging and implantation.1.3 The accelerated aging method specified herein has beenvalidated based on oxidation levels exhibited by certain shelf-aged

6、 UHMWPE components packaged in air and sterilizedwith gamma radiation. The method has not been shown to berepresentative of shelf aging when the UHMWPE is packagedin an environment other than air. For example, this practice hasnot been directly correlated with the shelf life of componentsthat have b

7、een sealed in a low-oxygen package, such asnitrogen. This practice is not intended to simulate any changethat may occur in UHMWPE following implantation.1.4 The values stated in SI units are to be regarded asstandard. The values given in parentheses are mathematicalconversions to inch-pound units th

8、at are for information onlyand are not considered standard.1.5 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bi

9、lity of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D883 Terminology Relating to PlasticsF648 Specification for Ultra-High-Molecular-Weight Poly-ethylene Powder and Fabricated Form for Surgical Im-plantsF1714 Guide for Gravimetric WearAssessment of ProstheticHip De

10、signs in Simulator DevicesF1715 Guide for Wear Assessment of Prosthetic Knee De-signs in Simulator Devices (Withdrawn 2006)32.2 ISO Standards:4ISO 5834 Implants for surgeryUltra-high molecularweight polyethyleneISO 14242 Implants for surgeryWear of total hip jointprosthesesISO 14243 Implants for sur

11、geryWear of total knee jointprostheses3. Terminology3.1 DefinitionsFor definitions of terms in this practicerelating to plastics, refer to Terminology D883. For definitionsof terms in this practice relating to UHMWPE, refer toSpecification F648 and ISO 5834.3.2 Definitions of Terms Specific to This

12、Standard:3.2.1 oxidation, nthe incorporation of oxygen into anothermolecule (for example, UHMWPE) by means of a chemicalreaction, resulting in the formation of a chemical covalentbond.3.2.2 oxygen bomb, na pressure vessel suitable for pre-conditioning of UHMWPE at an elevated temperature andpartial

13、pressure of oxygen.1This practice is under the jurisdiction ofASTM Committee F04 on Medical andSurgical Materials and Devices and is the direct responsibility of SubcommitteeF04.15 on Material Test Methods.Current edition approved May 1, 2015. Published July 2015. Originally approvedin 2002. Last pr

14、evious edition approved in 2008 as F2003 02 (2008). DOI:10.1520/F2003-02R15.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onth

15、e ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.4Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036, http:/www.ansi.org.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Con

16、shohocken, PA 19428-2959. United States14. Significance and Use4.1 This practice summarizes a method that may be used toaccelerate the oxidation of UHMWPE components usingelevated temperature and elevated oxygen pressure. Underreal-time conditions, such as shelf aging and implantation,oxidative chan

17、ges to UHMWPE after sterilization using highenergy radiation may take months or years to produce changesthat may result in deleterious mechanical performance. Themethod outlined in this practice permits the evaluation ofoxidative stability in a relatively short period of time (forexample, weeks).4.2

18、 This practice may also be used to oxidize UHMWPEtest specimens and joint replacement components prior tocharacterization of their physical, chemical, and mechanicalproperties. In particular, this practice may be used for acceler-ated aging of UHMWPE components prior to evaluation in ahip or knee jo

19、int wear simulator as outlined in Guide F1714(hip wear), Guide F1715 (knee wear), ISO 14242 (hip wear), orISO 14243 (knee wear), or combination thereof.5. Apparatus5.1 Combined ApparatusAn oxygen bomb (pressure ves-sel) apparatus that is capable of maintaining the desiredtemperature with an accuracy

20、 of 62C by itself may be used,providing it incorporates the requirements of 5.2 5.4.5.2 Pressure VesselIf a combined apparatus is not used, itwill be necessary to enclose the specimens within a pressurevessel, also known as an “oxygen bomb,” capable of with-standing a static pressure of 690 kPa (100

21、 psi). The pressurevessel shall be manufactured from stainless steel. The pressurevessel shall be equipped with either a regulator or a safetyrelease valve to maintain the internal pressure to the desiredvalue, when at equilibrium, to an accuracy of 67 kPa (61 psi).5.3 Because oxygen-air mixtures wi

22、ll be maintained atelevated temperatures for weeks at a time, it is recommendedthat a laboratory that is performing aging at elevated pressuretake appropriate safety precautions. For this reason, the use ofa commercially available and properly validated “oxygenbomb” is recommended. The pressure vess

23、el must be ofsuitable construction such that it does not leak, thereby leadingto the reduction of pressure during the two-week aging period.NOTE 1Oxygen flow and test interruption have been shown tosignificantly influence the outcome of accelerated aging studies.Consequently, the pressure vessel mus

24、t maintain nearly constant pressure(that is, within 67 kPa or 1 psi) throughout the duration of the testingperiod, or the results may not be reproducible or may be unreliable.5.4 Thermal ChamberIf a combined apparatus is not used,accelerated aging of the UHMWPE shall be conducted using athermal cham

25、ber that can maintain the desired temperaturewith an accuracy of 62C. The spatial variation of temperaturewithin the thermal chamber shall be measured using thermo-couples and verified to be less than 61C. Note that thethermal chamber will need to be sufficiently large to accom-modate the pressure v

26、essel, described in 5.2.5.5 Temperature ControllerThe combined apparatus orthermal chamber shall be equipped with a temperaturecontroller, capable of controlling the heating rate with anaccuracy of 0.1C/min.NOTE 2Temperature stability and test interruption has been shown tosignificantly influence th

27、e outcome of accelerated aging studies.Consequently, the pressure vessel must maintain nearly constant tempera-ture (that is, within 61C) throughout the duration of the testing period,or the results may not be reproducible or may be unreliable.6. Test Specimens6.1 The test specimens shall be prepare

28、d in final formaccording to the requirements of any subsequent physical,chemical, or mechanical tests to be performed after acceleratedaging. For example, if the specimens will ultimately besubjected to hip joint simulation, they should be prepared infinal form according to Guide F1714 and ISO 14242

29、.6.2 Finished specimens shall not be machined after accel-erated aging of (bulk) stock materials, because the acceleratedoxidation procedure outlined in this practice will result in aninhomogeneous distribution of chemical, physical, and hencemechanical properties through the thickness of an aged pa

30、rt.6.3 Test specimens shall be removed from their packagingprior to accelerated aging, because this practice is not intendedto reproduce the aging of UHMWPE that is stored in a lowoxygen environment.7. Validation of Apparatus7.1 Thermal Chamber ValidationUsing the calibratedtemperature sensor, valid

31、ate the temperature of the acceleratedaging apparatus to within 61C of the aging temperature.7.1.1 Verify the calibration of the temperature sensor(s) thatwill be used to validate the thermal conditions in the acceler-ating aging apparatus. The temperature sensor shall be cali-brated as defined in t

32、he manufacturers instructions.7.2 Pressure Vessel ValidationVerify the integrity of thepressure vessel to within 67 kPa (61 psi) by conducting thefollowing 14-day (336 6 1 h) validation test:7.2.1 Increase the pressure of pure oxygen inside the vesselby 503 kPa (73 psi) at 70 6 1C.7.2.2 Throughout t

33、he duration of the validation test, thegage pressure shall not vary by 67 kPa (61 psi).7.2.3 Pressure vessels that are not capable of maintainingthe target gage pressure within the stated tolerance shall beconsidered invalid for the purposes of accelerated aging untilthe excessive leaking has been r

34、ectified.7.3 The thermal chamber and pressure vessel shall bevalidated at least once per year, unless otherwise indicated bya specification or customer.8. Conditioning8.1 After high energy irradiation, specimens shall be main-tained at 23 6 2C (73.4 6 3.6F) for 28 days, starting fromthe date of irra

35、diation, prior to commencing accelerated aging,unless otherwise directed by the customer.8.2 After irradiation, specimens shall remain in their origi-nal packaging during the preconditioning period.F2003 02 (2015)28.3 Unirradiated specimens shall be maintained in a stan-dard laboratory environment o

36、f 23 6 2C (73.4 6 3.6F) for40 6 1 h prior to commencing accelerated aging.9. Procedure9.1 Specimen OrientationTest specimens shall be arrayedwithin the test chamber or oxygen bomb such that all relevantsurfaces have equivalent access to oxygen during the test. Forexample, with hip and knee component

37、s, the articulatingsurface which may subsequently be subjected to wear simula-tion shall not be obstructed or covered by other parts ormaterials that might interfere with uniform access of thesurface to oxygen.9.2 PressurizationThe pressure vessel shall be filled atroom temperature and purged with o

38、xygen at least three timesprior to starting the aging experiment. For example, at astandard laboratory environment, a change in pressure of 62.56 1 psi will be needed, such that the pressure increases to 503kPa (73 psi) as the at the target aging temperature of 70C isreached.9.3 Standard Relative Hu

39、midityWater shall not be addedto the pressure vessel during accelerated aging. The user shouldbe aware that adding water to the test chamber may affect theoxidation mechanism during the accelerated aging process.9.4 Initial Temperature and Heating RateThe pressurevessel is initially at standard labo

40、ratory temperature (23 62C) and will be gradually raised to the aging temperature of70C. The initial heating rate will be 1.0 6 0.1C/min.9.5 Accelerated AgingSpecimens are to be aged at aconstant temperature of 70 C and at an equilibrium gagepressure of 503 kPa (73 psi, 5 atmospheres) of pure oxygen

41、 for336 6 1 h (14 days) prior to subsequent testing. There are tobe no interruptions of the aging period (that is, no opening ofthe pressure vessel).9.6 Recording During the TestTemperature and pressurerecordings should be logged daily during the test period to noteany potential changes of the exper

42、imental conditions.9.7 Guide for Subsequent TestingSpecimens shall be sub-jected to further testing within two weeks after acceleratedaging.10. Reporting of Specimen Preparation and TestConditions10.1 The written report shall include details regarding thepreparation of the test samples, the chronolo

43、gy of the acceler-ated aging, and the storage conditions for the test samples.10.2 Test Sample PreparationThe investigator shall listthe size, shape, and method of manufacture of the test samples.The report shall also contain the type of resin used, themanufacturer/supplier of the UHMWPE, and any su

44、bsequentprocesses that were performed on the test articles aftermanufacture, such as sterilization or high energy irradiation.10.3 ChronologyThe report shall list the time at which thetest specimens were manufactured, subsequently sterilized, andlater aged. The report will also report the time that

45、anysubsequent analysis or testing was performed on the ageditems.10.4 Test Sample Storage ConditionsIt is important todocument the storage conditions of the test samples before andafter accelerated aging. The report shall indicate the environ-mental conditions (that is, storage in air versus nitroge

46、n) andtemperature under which the specimens were stored.11. Keywords11.1 aging; oxidation; preconditioning; stability; UHM-WPE; UHMW PE; ultra-high molecular weight polyethyleneAPPENDIX(Nonmandatory Information)X1. RationaleX1.1 Post-irradiation aging results in degradative changesto the physical, c

47、hemical, and mechanical properties of UHM-WPE. (1, 2)5Even under ambient conditions, oxidation ofirradiated UHMWPE evolves at a slow pace, with a degrada-tion rate measured in years. (1) As a result, accelerated agingtest methods have been developed in the past four years toaccelerate the oxidation

48、process in UHMWPE and therebyassess oxidative stability during a comparatively short timeperiod.X1.2 Oxidation of UHMWPE proceeds in a complex cas-cade of chemical reactions, which may be accelerated byincreasing the temperature or by increasing the concentrationof available oxygen, or both. (3) Con

49、sequently, in severalstudies, post-irradiation aging has been simulated using acombination of thermal oxidation and elevated oxygen pres-sure. (4, 5, 6) Despite the variation in test conditions reportedby these studies, accelerated oxidation protocols have increas-ingly been employed not only to characterize the effects ofgamma sterilization in air, but also to evaluate the oxidationresistance of UHMWPE sterilized by alternative methods.X1.3 Accelerated oxidation test methods for UHMWPE arenot without their limitations. Even though the met