ASTM E2127-2001A(2015)e1 Standard Methods of Static Load Test for Combined Tensile and Transverse Load Resistance of Paneled Wall Systems in Building Construction《房屋结构中隔墙系统耐拉伸与横向结合.pdf

《ASTM E2127-2001A(2015)e1 Standard Methods of Static Load Test for Combined Tensile and Transverse Load Resistance of Paneled Wall Systems in Building Construction《房屋结构中隔墙系统耐拉伸与横向结合.pdf》由会员分享，可在线阅读，更多相关《ASTM E2127-2001A(2015)e1 Standard Methods of Static Load Test for Combined Tensile and Transverse Load Resistance of Paneled Wall Systems in Building Construction《房屋结构中隔墙系统耐拉伸与横向结合.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: E2127 01a (Reapproved 2015)1Standard Methods ofStatic Load Test for Combined Tensile and Transverse LoadResistance of Paneled Wall Systems in BuildingConstruction1This standard is issued under the fixed designation E2127; the number immediately following the designation indicates the ye

2、ar oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1NOTEUnits statement was inserted in 1.4 editorially in March 2015

3、.1. Scope1.1 These test methods cover the procedures for determin-ing the resistance of paneled wall systems subjected to com-bined lateral loads and axial loads.1.2 These test methods involve the simultaneous applicationof transverse (lateral wind) and tensile (wind uplift) loads topaneled wall sys

4、tem assemblies anchored at both ends withhold-down connectors.1.3 These test methods are suitable for determining thestructural adequacy of the design, system, and wall fabricationtechnique, and are not intended to evaluate the strengthcapacity of the hold-down connectors.1.4 The values stated in in

5、ch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.5 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is

6、theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2E575 Practice for Reporting Data from Structural Tests ofBuilding Constructions, Ele

7、ments, Connections, and As-sembliesE631 Terminology of Building Constructions3. Terminology3.1 DefinitionsFor definitions of general terms used in thistest method, refer to Terminology E631.4. Summary of Test Method4.1 The tensile and bending capacity of the paneled wallsystem is determined by apply

8、ing a simultaneous tensile andtransverse load to a wall specimen. This is accomplished byanchoring one end of the specimen and applying a tensile loadto the opposing end while applying a transverse load; see Figs.1 and 2. The forces required to deflect the specimen and thecorresponding displacements

9、 at each load interval are mea-sured.5. Significance and Use5.1 The procedures described will test the behavior ofsegments of paneled wall system construction under conditionsrepresentative of those encountered in service. Performancecriteria based on data from those procedures can verifystructural

10、adequacy and service life.6. Test Apparatus6.1 Test Assembly:6.1.1 GeneralTests shall be made on three like specimensfor each orientation. All system elements shall be fastened in amanner to conform with the wall specifications. The wallsystem shall be representative of actual building construction.

11、6.1.2 ConnectionsThe performance of the wall is influ-enced by the type and spacing of the anchoring to the upper andlower ends of the wall.6.1.3 Paneled Wall System RequirementsThe paneled wallsystem specimen shall be comprised of members and connec-tors representative of those used in building con

12、struction,except that the specimen is permitted to consist of a core onwhich paneled wall system surface units are placed.6.1.4 Test SetupThe paneled wall system specimen shallbe tested vertically or horizontally so that surface units may be1These test methods are under the jurisdiction of ASTM Comm

13、ittee E06 onPerformance of Buildings and are the direct responsibility of Subcommittee E06.11on Horizontal and Vertical Structures/Structural Performance of Completed Struc-tures.Current edition approved March 1, 2015. Published March 2015. Originallyapproved in 2001. Last previous edition approved

14、in 2007 as E2127 01a (2007).DOI: 10.1520/E2127-01AR15E01.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.Copy

15、right ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1observed during the test. The test fixture shall allow forsimultaneous transverse and tensile load application. The topand bottom of the specimen shall be attached to rigid supports.6.1.5 Pa

16、neled Wall System SizeThe paneled wall systemspecimen height shall not be less than the actual height of thewall, and the width shall be minimum 48 in. (120 cm) wide, orthe width of an individual wall panel (if the individual panelwidth is greater than 48 in. wide).7. Procedure7.1 Number of TestsCon

17、duct a minimum of three tests foreach of the two orientations. Conduct the first set of tests withthe specimen orientation applicable to the positive pressureload application; see Fig. 1; conduct the second set of tests withthe specimen orientation applicable to the negative pressureload application

18、; see Fig. 2.FIG. 1 Test Specimen and Fixture, Straps UpE2127 01a (2015)127.1.1 LoadingThe loading procedure should be as fol-lows:7.1.1.1 Record midspan deflection values at “zero” load.7.1.1.2 Apply14 of the design tensile load along thelongitudinal axis of the paneled wall system specimen.7.1.1.3

19、 Allow a minimum of 5 min before recording themidspan displacement.7.1.1.4 Record the midspan displacement.7.1.1.5 Apply a uniformly distributed load equivalent to14the design lateral load over the entire surface of the specimen.7.1.1.6 Allow a minimum of 5 min before recording themidspan displaceme

20、nt.7.1.1.7 Record the midspan displacement.7.1.1.8 Repeat steps 7.1.1.2 7.1.1.7 increasing the tensileand lateral loads by14 design load increments until the 1.25design tensile and lateral load values are achieved.FIG. 2 Test Specimen and Fixture, Straps DownE2127 01a (2015)137.1.1.9 Record the mids

21、pan displacement.7.1.1.10 Remove the displacement measuring devices.7.1.1.11 Apply 2.5 times the design tensile load along thelongitudinal axis of the specimen.7.1.1.12 Apply a uniformly distributed load equivalent to2.5 times the design lateral load over the entire surface of thespecimen.7.1.1.13 C

22、hoose the rate of loading such that the anticipateddesign load level will be reached in not less than 20 min. Theduration of load application at each increment shall permit loadand deformation readings to be recorded. Apply the loads byhydraulic jack(s) or by other suitable types of loading appara-t

23、us that have been previously calibrated. Gages for measuringloads and displacement shall be accurate to within 2 % atdesign load. Record the duration of load at each level through-out the test.8. Calculation8.1 Base evaluation on the mean values resulting from testsof like specimens.8.2 The applied

24、axial load is to be equivalent to the upliftload acting on the section of the paneled wall system at thehold-down location.8.3 The lateral load is equivalent to positive or negativewind pressure acting on the section of the paneled wall system.8.4 Calculate the displacement at each load applicationi

25、nterval as the difference between the readings when the load isapplied and the initial reading at the start of the test.9. Report9.1 The report shall follow the format and contain informa-tion in accordance with Practice E575.10. Precision and Bias10.1 Because of the nature of these tests and the va

26、riety oftechniques that can be employed in conducting them, nostatement can be made about their precision and bias.11. Keywords11.1 axial load; combined loading; displacement; lateralload; paneled wall system; wall panel testingAPPENDIX(Nonmandatory Information)X1. TESTING FOR DISPLACEMENTX1.1 Due t

27、o the variety of materials that could be present ina paneled wall system, testing for displacement under variousloads becomes a simpler method when compared to analyticalcomputations.X1.2 The term design load refers to the load specified by thesponsor of the test.ASTM International takes no position

28、 respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.T

29、his standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM In

30、ternational Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address show

31、n below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 01a (2015)14