ASTM D4762-2011 Standard Guide for Testing Polymer Matrix Composite Materials《用于自动工业复合材料检验的标准指南》.pdf
《ASTM D4762-2011 Standard Guide for Testing Polymer Matrix Composite Materials《用于自动工业复合材料检验的标准指南》.pdf》由会员分享,可在线阅读,更多相关《ASTM D4762-2011 Standard Guide for Testing Polymer Matrix Composite Materials《用于自动工业复合材料检验的标准指南》.pdf(25页珍藏版)》请在麦多课文档分享上搜索。
1、Designation:D476208 Designation: D4762 11Standard Guide forTesting Polymer Matrix Composite Materials1This standard is issued under the fixed designation D4762; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revis
2、ion. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This guide summarizes the application of ASTM standard test methods (and other supporting standards) to continuous-fiberreinforc
3、ed polymer matrix composite materials. The most commonly used or most applicable ASTM standards are included,emphasizing use of standards of Committee D30 on Composite Materials.1.2 This guide does not cover all possible standards that could apply to polymer matrix composites and restricts discussio
4、n tothe documented scope. Commonly used but non-standard industry extensions of test method scopes, such as application of statictest methods to fatigue testing, are not discussed. A more complete summary of general composite testing standards, includingnon-ASTM test methods, is included in the Comp
5、osite Materials Handbook (MIL-HDBK-17).2Additional specific recommen-dations for testing textile (fabric, braided) composites are contained in Guide D6856.1.3 This guide does not specify a system of measurement; the systems specified within each of the referenced standards shallapply as appropriate.
6、 Note that the referenced standards of ASTM Committee D30 are either SI-only or combined-unit standardswith SI units listed first.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibilityof the user of this standard to establi
7、sh appropriate safety and health practices and determine the applicability of regulatorylimitations prior to use.2. Referenced Documents2.1 ASTM Standards:32.1.1 Standards of Committee D30 on Composite MaterialsC271/C271M Test Method for Density of Sandwich Core MaterialsC272 Test Method for Water A
8、bsorption of Core Materials for Structural Sandwich ConstructionsC273/C273M Test Method for Shear Properties of Sandwich Core MaterialsC297/C297M Test Method for Flatwise Tensile Strength of Sandwich ConstructionsC363/C363M Test Method for DelaminationNode Tensile Strength of Honeycomb Core Material
9、sC364/C364M Test Method for Edgewise Compressive Strength of Sandwich ConstructionsC365/C365M Test Method for Flatwise Compressive Properties of Sandwich CoresC366/C366M Test Methods for Measurement of Thickness of Sandwich CoresC393/C393M Test Method for Core Shear Properties of Sandwich Constructi
10、ons by Beam FlexureC394 Test Method for Shear Fatigue of Sandwich Core MaterialsC480480/C480M Test Method for Flexure Creep of Sandwich ConstructionsC481 Test Method for Laboratory Aging of Sandwich ConstructionsC613/C613M Test Method for Constituent Content of Composite Prepreg by Soxhlet Extractio
11、nD2344/D2344M Test Method for Short-Beam Strength of Polymer Matrix Composite Materials and Their LaminatesD3039/D3039M Test Method for Tensile Properties of Polymer Matrix Composite MaterialsD3171 Test Methods for Constituent Content of Composite Materials1This guide is under the jurisdiction ofAST
12、M Committee D30 on Composite Materials and is the direct responsibility of Subcommittee D30.01 on Editorial and ResourceStandards.Current edition approved April 1, 2008. Published September 2008. Originally approved in 1988. Last previous edition approved in 2004 as D476204. DOI:10.1520/D4762-08.Cur
13、rent edition approved Jan. 15, 2011. Published February 2011. Originally approved in 1988. Last previous edition approved in 2008 as D4762 08. DOI:10.1520/D4762-11.2Available from ASTM, and also from the U.S. DoD Standardization Documents Order Desk, Bldg. 4 Section D, 700 Robbins Ave., Philadelphia
14、, PA 19111-5094, Attn:NPODS.2Available from Standardization Documents Order Desk, DODSSP, Bldg. 4, Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http:/dodssp.daps.dla.mil.3For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at serviceastm
15、.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.1This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becaus
16、eit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.Copyright ASTM International, 100 Bar
17、r Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.D3410/D3410M Test Method for Compressive Properties of Polymer Matrix Composite Materials with Unsupported GageSection by Shear LoadingD3479/D3479M Test Method for Tension-Tension Fatigue of Polymer Matrix Composite Materia
18、lsD3518/D3518M Test Method for In-Plane Shear Response of Polymer Matrix Composite Materials by Tensile Test of a 45LaminateD3529/D3529M Test Method for Matrix Solids Content and Matrix Content of Composite PrepregD3530/D3530M Test Method for Volatiles Content of Composite Material PrepregD3531 Test
19、 Method for Resin Flow of Carbon Fiber-Epoxy PrepregD3532 Test Method for Gel Time of Carbon Fiber-Epoxy PrepregD3800 Test Method for Density of High-Modulus FibersD3878 Terminology for Composite MaterialsD4018 Test Methods for Properties of Continuous Filament Carbon and Graphite Fiber TowsD4102 Te
20、st Method for Thermal Oxidative Resistance of Carbon FibersD4255/D4255M Test Method for In-Plane Shear Properties of Polymer Matrix Composite Materials by the Rail Shear MethodD5229/D5229M Test Method for Moisture Absorption Properties and Equilibrium Conditioning of Polymer Matrix CompositeMaterial
21、sD5379/D5379M Test Method for Shear Properties of Composite Materials by the V-Notched Beam MethodD5448/D5448M Test Method for Inplane Shear Properties of Hoop Wound Polymer Matrix Composite CylindersD5449/D5449M Test Method for Transverse Compressive Properties of Hoop Wound Polymer Matrix Composit
22、e CylindersD5450/D5450M Test Method for Transverse Tensile Properties of Hoop Wound Polymer Matrix Composite CylindersD5467/D5467M Test Method for Compressive Properties of Unidirectional Polymer Matrix Composite Materials Using aSandwich BeamD5528 Test Method for Mode I Interlaminar Fracture Toughn
23、ess of Unidirectional Fiber-Reinforced Polymer MatrixCompositesD5687/D5687M Guide for Preparation of Flat Composite Panels with Processing Guidelines for Specimen PreparationD5766/D5766M Test Method for Open-Hole Tensile Strength of Polymer Matrix Composite LaminatesD5961/D5961M Test Method for Bear
24、ing Response of Polymer Matrix Composite LaminatesD6115 Test Method for Mode I Fatigue Delamination Growth Onset of Unidirectional Fiber-Reinforced Polymer MatrixCompositesD6264/D6264M Test Method for Measuring the Damage Resistance of a Fiber-Reinforced Polymer-Matrix Composite to aConcentrated Qua
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMD47622011STANDARDGUIDEFORTESTINGPOLYMERMATRIXCOMPOSITEMATERIALS 用于 自动 工业 复合材料 检验 标准 指南 PDF

链接地址:http://www.mydoc123.com/p-517913.html