ASTM D4370-2001(2017) Standard Test Methods for Acid and Base Milliequivalent Content of Electrocoat Bath《电涂镀槽中酸和碱毫当量常数的标准试验方法》.pdf

《ASTM D4370-2001(2017) Standard Test Methods for Acid and Base Milliequivalent Content of Electrocoat Bath《电涂镀槽中酸和碱毫当量常数的标准试验方法》.pdf》由会员分享，可在线阅读，更多相关《ASTM D4370-2001(2017) Standard Test Methods for Acid and Base Milliequivalent Content of Electrocoat Bath《电涂镀槽中酸和碱毫当量常数的标准试验方法》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D4370 01 (Reapproved 2017)Standard Test Methods forAcid and Base Milliequivalent Content of Electrocoat Bath1This standard is issued under the fixed designation D4370; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, th

2、e year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 These test methods cover the determination of acid andbase milliequivalent contents of anodic and cathodic e

3、lectro-coat baths and their ultrafiltrates.1.2 The values stated in SI units are to be regarded asstandard. No other units of measurement are included in thisstandard.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of

4、the user of this standard to establish appro-priate safety, health, and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization establis

5、hed in the Decision on Principles for theDevelopment of International Standards, Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2D1193 Specification for Reagent Water3. Summary of Test Methods3.1

6、 Specimens are titrated with standard acid and alkalisolutions respectively. Alternative procedures are given fordetermining acid and base concentrations potentiometrically orusing a pH meter.4. Significance and Use4.1 The acid and base concentrations are a measurement ofthe titratable acidic and al

7、kaline components in the electrocoatbaths. These measurements are used for research, production orelectrocoat bath process control.5. Apparatus5.1 Automatic Potentiometric Titrator with Stirrer andRecorder, any model.5.2 Analytical Balance, with sensitivity of 0.1 mg.5.3 pH Meter, any model.5.4 Glas

8、s and Saturated Calomel Electrodes.5.5 Syringes, 5-mL disposable.6. Reagents6.1 Purity of ReagentsReagent grade chemicals shall beused in all tests. Unless otherwise indicated, it is intended thatall reagents shall conform to the specifications of the Commit-tee on Analytical Reagents of the America

9、n Chemical Society,where such specifications are available.3Other grades may be used, provided it is ascertained that thereagent is of sufficiently high purity to permit its use withoutlessening the accuracy of the determination.6.2 Purity of WaterReferences to water shall be under-stood to mean wat

10、er conforming to Type II of SpecificationD1193.6.3 Potassium Hydroxide Solution in Methanol, 0.1NPrepare by dissolving 5.6 g of potassium hydroxide (KOH)pellets in 1 L of methanol. Standardize against NIST standardreference material of acid potassium phthalate No. 84 using anautomatic potentiometric

11、 titrator4to a given end point or,alternatively, to a phenolphthalein end point.6.4 Hydrochloric Acid Solution , 0.1 NPrepare by mixingabout 8.50 mL of concentrated hydrochloric acid (HCl) (1.19sp gr) into a mixture of 600 mL water and 400 mL methanol.Standardize against 0.1 N potassium hydroxide so

12、lution (see6.3).1These test methods are under the jurisdiction of ASTM Committee D01 onPaint and Related Coatings, Materials, and Applications and are the directresponsibility of Subcommittee D01.21 on Chemical Analysis of Paints and PaintMaterials.Current edition approved Dec. 1, 2017. Published De

13、cember 2017. Originallyapproved in 1984. Last previous edition approved in 2012 as D4370 01 (2012).DOI: 10.1520/D4370-01R17.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, r

14、efer to the standards Document Summary page onthe ASTM website.3Reagent Chemicals, American Chemical Society Specifications, AmericanChemical Society, Washington, DC. For suggestions on the testing of reagents notlisted by the American Chemical Society, see Analar Standards for LaboratoryChemicals,

15、BDH Ltd., Poole, Dorset, U.K., and the United States Pharmacopeiaand National Formulary, U.S. Pharmacopeial Convention, Inc. (USPC), Rockville,MD.4Svehla, G., Automatic Potentiometric Titration, Pergamon Press, 1978, p. 187.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Consh

16、ohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Org

17、anization Technical Barriers to Trade (TBT) Committee.16.5 1,3-Propanediol (Propylene Glycol) (PG).6.6 Tetrahydrofuran (THF).6.7 Reference pH Standard SolutionsCommercial stan-dards of pH 4.0, 7.0, and 10.0.7. Sampling and Sample Preparation7.1 The sample should be obtained while the electrocoatbath

18、 is under proper circulation such that a uniform material isobtained. In case of an ultrafiltrate, the material should bethoroughly mixed or stirred prior to sampling to assureuniformity.7.2 After sampling and prior to removing a test specimen, itis mandatory that the samples be shaken or stirred un

19、til they arehomogeneous and free of any settled material. This is particu-larly important if there is a delay between sampling the bathand performing the test. The absence of settled material can beascertained visually (in a transparent container) or by insertinga spatula, scraping the bottom of the

20、 container, and makingsure that there is no settled matter. The shaking or stirring ofthe samples should be carried out up to the moment of takinga specimen; this Point is Very Important.8. Base Concentration Content8.1 Stir the sample very thoroughly to disperse materialsthat might have settled to

21、the bottom of the container. With theaid of a syringe, withdraw approximately 5 mL of the samplequickly, weigh the full syringe to 0.1 mg, and record thisweight as W1. Transfer the entire contents of the syringe into a100-mL beaker. Reweigh the empty syringe to 0.1 mg andrecord as W2. Duplicate the

22、procedure using a second speci-men.8.2 Add approximately 40 mL of THF/PG 80/20 mixture tothe specimens in the beakers and cover, preferably withaluminum foil, to minimize evaporation of the solvent mixture.NOTE 1In cases where the recommended THF/PG 80/20 mixturecauses precipitation of the material,

23、 substitute the same amount of anappropriate solvent or solvent mixture to a new specimen. The formationof a precipitate during the titration might foul the electrode system andmask potentiometric changes. Other solvents suitable for dilution areacetone, dimethylformamide, toluene, or methanol. Any

24、other solvent orsolvent mixture that does not cause the formation of a precipitatethroughout the titration is suitable. In certain instances it may be necessaryto run a titration blank and to make the appropriate corrections for thesolvent.8.3 Titrate both specimens with 0.1 N HCl solution usingthe

25、automatic potentiometric titrator until an end point “break”is reached.4Add approximately 5 mL of additional titrant tocomplete the curve. A typical titration curve is shown in Fig. 1.Record as V1the volume of titrant needed for the end point.NOTE 2If the titration curve does not show an inflection

26、point (endpoint), back titration with 0.1 N KOH will give an acceptable result.9. Base Content Calculation9.1 Calculate the base content as follows:A 5V13 N1!3100W12 W2!Mwhere:A = milliequivalents of base per gram of nonvolatilematter,V1= volume of HCl titrant used, mL,N1= normality of HCl titrant,W

27、1= mass of the syringe filled with sample, mg,W2= mass of the empty syringe after delivery of thespecimen, mg, andM = nonvolatile matter content, %.10. Acid Concentration Content10.1 Using a fresh portion of the sample, follow 8.1 and 8.2.10.2 Titrate both specimens with 0.1 N KOH solution usingthe

28、automatic potentiometric titrator until an end point break isreached.Add about 5 mL more of titrant to complete the curve.From the curve, determine and record, as V2, the volume oftitrant needed for the end point.411. Acid Content Calculation11.1 Calculate the acid content as follows:A 5V23 N2! 3100

29、W32 W4!M(a) Acid Milliequivalent Content Titration(b) Base Milliequivalent Content TitrationFIG. 1 Potentiometric Titration Curves for the Acid and Base Mil-liequivalent ContentD4370 01 (2017)2where:A = milliequivalents of acid per gram of nonvolatilematter,V2= volume of KOH titrant used, mL,N2= nor

30、mality of KOH titrant,W3= mass of the syringe filled with sample, mg,W4= mass of the empty syringe after delivery of thespecimen, mg, andM = nonvolatile matter content, %.12. Base Concentration Content Using a pH Meter12.1 Proceed in accordance with 8.1 and 8.2.12.2 Standardize the pH meter at 4.0 a

31、nd 7.0.12.3 Titrate both specimens with 0.1 N HCl until a pH of 4.0is obtained. Make certain that the solutions are well agitatedduring titration (a magnetic stirrer is recommended). Recordvolume of titrant, as V1, used for each titration. Becauseelectrocoating paints vary greatly, it might be advis

32、able totitrate to a pH value agreed upon between the producer and theuser.13. Base Content Calculation13.1 Calculate the base content as described in Section 9.14. Acid Concentration Content Using a pH Meter14.1 Proceed in accordance with 8.1 and 8.2.14.2 Standardize the pH meter at 7.0 and 10.0.14.

33、3 Titrate both specimens with 0.1 N KOH until a pH of10.0 is obtained. Make certain that solutions are well agitatedduring titration (a magnetic stirrer is recommended). Recordvolume of titrant, as V2used for each.15. Acid Content Calculation15.1 Calculate the acid content as described in Section 11

34、.16. Precision and Bias16.1 PrecisionIn an interlaboratory study of the testmethods, in which six laboratories measured in duplicate ontwo days four electrocoat samples with acid and base mil-liequivalents ranging from 0.2 to 0.8, the within-laboratorycoefficient of variation, after discarding one r

35、esult, was foundto be 1.4 % relative at 23 df and the between-laboratorycoefficient of variation 5.7 % relative at 19 df. Based on thesecoefficients, the following criteria should be used for judgingthe acceptability of results at the 95 % confidence level:16.1.1 RepeatabilityTwo results, each the m

36、ean of dupli-cate determination, obtained by the same operator on differentdays should be considered suspect if they differ by more than4.1 % relative.16.1.2 ReproducibilityTwo results, each the mean of du-plicate determinations, obtained by operators in different labo-ratories should be considered

37、suspect if they differ by morethan 17 % relative.16.2 BiasBias cannot be determined because there are noaccepted standards for acid or base content of electrocoatbaths.17. Keywords17.1 acid content; base content; electrocoat bathsASTM International takes no position respecting the validity of any pa

38、tent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revisio

39、n at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your com

40、ments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyright

41、ed by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 01 (2017)3