ASTM D3678-1997(2008)e1 Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Interior-Profile Extrusions《硬质聚氯乙烯(PVC)内异型挤压料的标准规范》.pdf

《ASTM D3678-1997(2008)e1 Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Interior-Profile Extrusions《硬质聚氯乙烯(PVC)内异型挤压料的标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM D3678-1997(2008)e1 Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Interior-Profile Extrusions《硬质聚氯乙烯(PVC)内异型挤压料的标准规范》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D 3678 97 (Reapproved 2008)e1An American National StandardStandard Specification forRigid Poly(Vinyl Chloride) (PVC) Interior-Profile Extrusions1This standard is issued under the fixed designation D 3678; the number immediately following the designation indicates the year oforiginal ado

2、ption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.e1NOTEEditorial changes were made throughout in April 2008.1. Scope*1.1 This speci

3、fication establishes requirements for the ma-terial properties, including dimensional stability and extrusionquality, of rigid, poly(vinyl chloride) (PVC) interior-profileextrusions. Methods for identifying interior-profile extrusionsthat comply with the requirements of this specification areprovide

4、d.1.2 Rigid PVC recycled plastic may be used in this productin accordance with the requirements in Sections 6 and 7.1.3 Rigid PVC compounds for interior building productapplications are covered in Specification D 1784.1.4 Rigid PVC exterior profile extrusions for assembledwindows and doors are cover

5、ed in Specification D 4726.1.5 The text of this standard references notes and footnoteswhich provide explanatory material. These notes and footnotes(excluding those in Tables and Figures) shall not be consideredas requirements of this standard.1.6 The values stated in SI units are to be regarded as

6、thestandard. The values given in parentheses are given forinformation only.NOTE 1Information with regard to application should be obtainedfrom the manufacturers of the profiles.NOTE 2There is no know ISO equivalent to this standard.1.7 The following precautionary caveat pertains only to thetest meth

7、od portion, Section 8, of this specification: Thisstandard does not purport to address all of the safety concerns,if any, associated with its use. It is the responsibility of the userof this standard to establish appropriate safety and healthpractices and determine the applicability of regulatory li

8、mita-tions prior to use.2. Referenced Documents2.1 ASTM Standards:D 618 Practice for Conditioning Plastics for TestingD 696 Test Method for Coefficient of Linear Thermal Ex-pansion of Plastics Between 30C and 30C with aVitreous Silica DilatometerD 883 Terminology Relating to PlasticsD 1042 Test Meth

9、od for Linear Dimensional Changes ofPlastics Under Accelerated Service ConditionsD 1600 Terminology for Abbreviated Terms Relating toPlasticsD 1784 Specification for Rigid Poly(Vinyl Chloride) (PVC)Compounds and Chlorinated Poly(Vinyl Chloride)(CPVC) CompoundsD 2152 Test Method for Adequacy of Fusio

10、n of ExtrudedPoly(Vinyl Chloride) (PVC) Pipe and Molded Fittings byAcetone ImmersionD 3892 Practice for Packaging/Packing of PlasticsD 4726 Specification for Rigid Poly(Vinyl Chloride) (PVC)Exterior-Profile Extrusions Used for Assembled Windowsand DoorsD 4968 Guide for Annual Review of Test Methods

11、andSpecifications for PlasticsD 7209 Guide for Waste Reduction, Resource Recovery,and Use of Recycled Polymeric Materials and ProductsE 631 Terminology of Building Constructions3. Terminology3.1 GeneralDefintions are in accordance with Terminol-ogy D 883 or Terminology E 631 and abbreviations withTe

12、rminology D 1600, unless otherwise indicated.4. Significance and Use4.1 The purpose of this specification is to establish on anational basis, a recognized standard of quality for rigidpoly(vinyl chloride) (PVC) interior-profile extrusions for inte-rior use other than cellular products, piping, tubin

13、g, andwindow and door profiles used in finished building products.The information contained in this standard is intended to behelpful to producers, distributors, and users, and to promoteunderstanding between buyers and sellers. It is also intended toserve as the basis for requirements on finished i

14、nterior buildingproducts which are either made from or employ rigid PVCprofile extrusions in their construction.1This specification is under the jurisdiction of ASTM Committee D20 onPlastics and is the direct responsibility of Subcommittee D20.24 on Plastic BuildingProducts.Current edition approved

15、March 1, 2008. Published April 2008. Originallyapproved in 1978. Last previous edition approved in 2001 as D 3678 97(2001).1*A Summary of Changes section appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United Sta

16、tes.5. Classification5.1 This standard covers three classes of rigid PVC interior-profile extrusions as follows:Class 1Normal impactClass 2Intermediate impactClass 3High impact6. Materials and Manufacture6.1 This specification covers profile extrusions made fromplastics conforming to the requirement

17、s of SpecificationD 1784. Class 1 extrusions shall meet the requirements speci-fied in Specification D 1784 for Class 12454 compound. Class2 extrusions shall meet the requirements for Class 14323compound. Class 3 extrusions shall meet the requirements forClass 1-40031-54-0000 compound. Refer to Tabl

18、e 1 in Speci-fication D 1784.6.2 Rigid PVC recycled plastic, as defined in Guide D 7209,may be used in this product if all the requirements in thesections on Materials and Manufacture (Section 6), and onPhysical Requirements (Section 7) are met by the extrusionscontaining PVC recycled plastic.6.3 Al

19、l Class compounds shall have a minimum coefficientof linear expansion of 10 3 10-5cm/cm/C (5.5 3 10-5in./in./F).NOTE 3Non-PVC materials may be used as a capstock.6.4 Rework MaterialClean, homogeneous PVC reworkmaterial or rework material containing PVC capstock gener-ated from the manufacturers own

20、production of the same classcompound may be used by the same manufacturer providingthat the extruded profiles meet all the requirements of thisspecification. Clean principally PVC rework material contain-ing non-PVC capstock may be used only in the substrate of acapstocked product by the same manufa

21、cturer, providing thatthe extruded profiles meet all of the requirements of thisspecification.6.5 The PVC compound in extruded section shall maintainuniform color and be free of any visual surface or structuralchanges, such as peeling, chipping, cracking, flaking, orpitting.7. Physical Requirements7

22、.1 DimensionsThe size, thickness, and dimensional tol-erances of the interior-profile extrusions shall be as agreedupon between the supplier and purchaser.7.2 Dimensional StabilityThe dimensional stability of theinterior-profile extrusions shall be determined in the extrusiondirection in accordance

23、with 8.5. Extrusions over 1.02 mm(0.040 in.) in thickness shall have a maximum shrinkage of2.2 %; those of 1.02-mm (0.040-in.) thickness or less shallhave a 3.0 % maximum shrinkage.7.3 Extrusion QualityThe extrusion quality of Class 1extrusions shall be determined by immersion in anhydrousacetone in

24、 accordance with the requirements of 8.6. Specimensof extrusions having not more than 25 % surface attack shall beconsidered as adequately fused and of satisfactory quality. Theextrusion qualities of Class 2 and Class 3 extrusions shall be asagreed upon between the supplier and purchaser.8. Test Met

25、hods8.1 GeneralUse the inspection and test procedures con-tained in this section to determine the conformance of productsto the requirements of this specification. Each producer ordistributor who represents his products as conforming to thisspecification may utilize statistically based sampling plan

26、s thatare appropriate for each particular manufacturing process, butshall keep such essential records as are necessary to documentwith a high degree of assurance his claim that all of therequirements of this specification have been met. Additionalsampling and testing of the product, as may be agreed

27、 uponbetween supplier and purchaser, is not precluded by thissection.8.2 Visual InspectionVisually examine the interior-profileextrusions to determine their compliance with the requirementsof 6.5.8.3 Conditioning of SpecimensCondition the test speci-mens in accordance with ProcedureAof Practice D 61

28、8, exceptthat the minimum conditioning time shall be 24 h.8.4 Test ConditionsConduct the tests the Standard Labo-ratory Atmosphere of 23 6 1C (73.4 6 1.8F) and 50 6 5%relative humidity, unless otherwise specified in the applicabletest method.8.5 Dimensional StabilityDetermine the dimensional sta-bil

29、ity in accordance with Test Method D 1042, except that thetest cycle shall consist of heating the specimens for 30 min ina uniformly heated oven at a temperature of 82.0 6 0.6C (1806 1F).8.6 Extrusion QualityDetermine the extrusion quality inaccordance with Test Method D 2152, except that the testsp

30、ecimens shall be 25.40 to 50.80 mm (1 to 2 in.) in length andsufficient in number to ensure testing the complete crosssection. In the test procedure described, the interior-profileextrusions will normally swell and soften in contact withanhydrous acetone. In some cases there may be surface attack.Di

31、sintegration is defined as complete separation of flakes orpieces from the body of the extrusion.8.7 Coeffcient of Linear ExpansionConduct this test inaccordance with Test Method D 696.9. Product Marking9.1 In order that purchasers may identify products conform-ing to all requirements of this specif

32、ication, producers anddistributors may include a statement of compliance in conjunc-tion with their name and address on product labels, invoices,sales literature, and the like. The following statement issuggested when sufficient space is available:“The product conforms to all of the requirements est

33、ablishedin ASTM D 3678, developed cooperatively with the industryand published by ASTM.”“Full responsibility for the conformance of this product tothis specification is assumed by (name and address of produceror distributor).”9.2 The following abbreviated statement is suggested whenavailable space o

34、n labels is insufficient for the full statement:“Conforms to ASTM D 3678 (name and address of produceror distributors).”D 3678 97 (2008)e129.3 All packing, packaging, and marking provisions ofPractice D 3892 shall apply to this specification.10. Packaging10.1 The interior-profile extrusions shall be

35、 packaged insuch a manner as to provide reasonable protection againstdamage in ordinary handling and transportation.11. Keywords11.1 building products; extrusion; interior profile extru-sions; recycled plastic; rigid poly(vinyl chloride)SUMMARY OF CHANGESCommittee D20 has identified the location of

36、selected changes to this standard since the last issue (D367897(2001) that may impact the use of this standard.(1) Reworded ISO equivalency statement per Guide D 4968.(2) Deleted D 5033 reference in Section 2and added GuideD 7209.(3) Deleted D 5033 reference in Section 6 and added GuideD 7209.(4) Ad

37、justed significant digits in 8.4 and 8.5.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and th

38、e riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision o

39、f this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you should

40、make your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).D 3678 97 (2008)e13