ASTM C1064 C1064M-2012 Standard Test Method for Temperature of Freshly Mixed Hydraulic-Cement Concrete《新拌水硬水泥混凝土温度的标准试验方法》.pdf

《ASTM C1064 C1064M-2012 Standard Test Method for Temperature of Freshly Mixed Hydraulic-Cement Concrete《新拌水硬水泥混凝土温度的标准试验方法》.pdf》由会员分享，可在线阅读，更多相关《ASTM C1064 C1064M-2012 Standard Test Method for Temperature of Freshly Mixed Hydraulic-Cement Concrete《新拌水硬水泥混凝土温度的标准试验方法》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: C1064/C1064M 11 C1064/C1064M 12Standard Test Method forTemperature of Freshly Mixed Hydraulic-Cement Concrete1This standard is issued under the fixed designation C1064/C1064M; the number immediately following the designation indicates theyear of original adoption or, in the case of revi

2、sion, the year of last revision. A number in parentheses indicates the year of lastreapproval. A superscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope*1.1 This test method c

3、overs the determination of temperature of freshly mixed hydraulic-cement concrete.1.2 The values stated in either SI or inch-pound units are to be regarded separately as standard. The values stated in each systemmay not be exact equivalents; therefore, each system shall be used independently of the

4、other. Combining values from the twosystems may result in non-conformance with the standard.1.3 The text of this standard references notes and footnotes that provide explanatory information. These notes and footnotes(excluding those in tables and figures) shall not be considered as requirements of t

5、his standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibilityof the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatorylimitations prior to use. (Wa

6、rningFresh hydraulic cementitious mixtures are caustic and may cause chemical burns to skin andtissue upon prolonged exposure.2)2. Referenced Documents2.1 ASTM Standards:3C172 Practice for Sampling Freshly Mixed ConcreteC670 Practice for Preparing Precision and Bias Statements for Test Methods for C

7、onstruction Materials3. Significance and Use3.1 This test method provides a means for measuring the temperature of freshly mixed concrete. The measured temperaturerepresents the temperature at the time of testing and may not be an indication of the temperature of the freshly mixed concrete ata later

8、 time. It may be used to verify conformance to a specified requirement for temperature of concrete.3.2 Concrete containing aggregate of a nominal maximum size greater than 75 mm 3 in. may require up to 20 min for thetransfer of heat from aggregate to mortar. (See ACI Committee 207.1R Report.4)4. App

9、aratus4.1 Container, shall be large enough to provide at least 75 mm 3 in. of concrete in all directions around the sensor of thetemperature measuring device; concrete cover must also be at least three times the nominal maximum size of the coarse aggregate.4.2 Temperature Measuring Device, shall be

10、capable of accurately measuring the temperature of the freshly mixed concrete to6 0.5 C 61 F throughout a range of 0 to 50 C 30 to 120 F. The design of the temperature measuring device shall be suchthat it allows 75 mm 3 in. or more immersion during operation.4.3 Partial immersion liquid-in-glass th

11、ermometers (and possibly other types) shall have a permanent mark to which the devicemust be immersed without applying a correction factor.1 This test method is under the jurisdiction of ASTM Committee C09 on Concrete and Concrete Aggregatesand is the direct responsibility of Subcommittee C09.60 onT

12、esting Fresh Concrete.Current edition approved Dec. 1, 2011Dec. 1, 2012. Published January 2012January 2013. Originally approved in 1986. Last previous edition approved in 20082011 asC106408.11. DOI: 10.1520/C1064_C1064M-11.10.1520/C1064_C1064M-12.2 Section on Safety Precautions, Manual of Aggregate

13、 and Concrete Testing, Annual Book of ASTM Standards, Vol 04.02.3 For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM we

14、bsite.4 Available from American Concrete Institute (ACI), P.O. Box 9094, Farmington Hills, MI 48333-9094, http:/www.concrete.org.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Be

15、causeit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.*A Summary of Changes section app

16、ears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States14.4 Reference Temperature Measuring Device, shall be readable and accurate to 6 0.2 C 0.5 F at the verification points in5.1. A certificate or report that

17、 verifies the accuracy shall be available in the laboratory for review. Accuracy of liquid-in-glassreference temperature measuring devices shall be verified once. Verification of direct-reading resistance reference temperaturemeasuring devices shall be performed every twelve months. The certificate

18、or report shall provide documentation that the referencestandard used in the verification is traceable to the National Institute of Standards and Technology (NIST).5. Verification of the Accuracy of Temperature Measuring Devices5.1 The accuracy of each temperature measuring device used for determini

19、ng the temperature of freshly mixed concrete shallbe verified annually, or whenever there is a question of accuracy. Verify the accuracy of the temperature measuring device bycomparing the readings of the reference temperature measuring device to the temperature measuring device at two temperaturesa

20、t least 15 C 30 F apart.5.2 Verification of the accuracy of the temperature measuring devices may be made in oil or other suitable bath liquids havinguniform density if provision is made to:5.2.1 Maintain the bath temperature constant within 0.2 C 0.5 F during the verification process.5.2.2 Continuo

21、usly circulate the bath liquid to provide a uniform temperature throughout the bath.5.2.3 Suspend the temperature measuring devices in such a manner that the devices are not contacting the sides or bottom ofthe bath container during verification.5.3 Place both the temperature and reference temperatu

22、re measuring devices in the bath for at least 5 min before readingtemperatures at the test points specified in 5.1.5.4 Prior to reading the temperature measuring devices, if the temperature in the bath has been reduced, slightly tapthermometers containing liquid to avoid adhesion of the liquid to th

23、e glass.5.5 Read and record the temperature of both the reference temperature measuring device and the temperature measuring device.Reject the temperature measuring device if the difference in readings exceeds 0.5 C 1 F at either test point. If the indicator ofthe rejected temperature measuring devi

24、ce is adjustable, reverification is permitted after adjustment. In addition to the temperaturereadings, record the identification numbers of both devices used, the date verified, and the name of individual performing theverification.6. Sampling Concrete6.1 It is acceptable to measure the temperature

25、 of freshly mixed concrete in either the transporting equipment or the forms afterdischarge provided the sensor of the temperature measuring device has at least 75 mm 3 in. of concrete cover in all directions.6.2 If the transporting equipment or placement forms are not used as the container, a sampl

26、e shall be prepared as follows:6.2.1 Immediately, prior to sampling the freshly mixed concrete, dampen (with water) the sample container.6.2.2 Sample the freshly mixed concrete in accordance with Practice C172, except that composite samples are not required ifthe only purpose for obtaining the sampl

27、e is to determine temperature.6.2.3 Place the freshly mixed concrete into the container.7. Procedure7.1 Position the temperature measuring device so that the end of the temperature sensing portion is submerged a minimum of75 mm 3 in. into the freshly mixed concrete. Close the void left by the placem

28、ent by gently pressing the concrete around thetemperature measuring device at the surface of the concrete to prevent ambient air temperature from affecting the reading.7.2 Leave the temperature measuring device in the freshly mixed concrete for at least 2 min but not more than 5 min, then readand re

29、cord the temperature to the nearest 0.5 C 1 F. Do not remove the device from the concrete when reading the temperature.8. Report8.1 Report the measured temperature of the freshly mixed concrete to the nearest 0.5 C 1 F.9. Precision and Bias9.1 The data used to develop the precision statement were ob

30、tained using the inch-pound version of this test method. Theprecision indices shown in SI units are conversions of the values in brackets.9.2 The single operator standard deviation for measurement of concrete temperature has been found to be 0.5 F. 0.3 C 0.5F. 5 Therefore, results of two properly co

31、nducted tests by the same operator on the same sample of material should not differ bymore than 1.3 F. 0.7 C 1.3 F. 55 These numbers represent, respectively, the (1s) and (d2s) limits as described in Practice C670.C1064/C1064M 1229.3 The multi-operator standard deviation for the measurement of concr

32、ete temperature on the same sample has been found tobe 0.7 F. 0.4 C 0.7 F. 5 Therefore, two tests properly conducted by different operators but on the same material should notdiffer by more than 1.9 F. 1.1 C 1.9 F. 59.4 The precision values given were derived from an inter-laboratory study using 11

33、operators on two concrete batches at around75 F. 24 C 75 F. 69.5 Since there is no accepted reference material suitable for determining the bias of this test method, no statement on bias isbeing made.10. Keywords10.1 freshly mixed concrete; temperature; temperature measuring deviceSUMMARY OF CHANGES

34、Committee C09 has identified the location of selected changes to this specification since the last issue,C1064/C1064M11, that may impact the use of this specification. (Approved December 1, 2012)(1) Added new 9.1 to indicate that precision values were obtained using the inch-pound version of the tes

35、t method and renumberedsubsequent subsections.SUMMARY OF CHANGESCommittee C09 has identified the location of selected changes to this specification since the last issue,C1064/C1064M08, that may impact the use of this specification. (Approved December 1, 2011)(1) Revised 1.2 to conform to the ASTM Fo

36、rm and Style.6 Supporting data have been filed at ASTM International Headquarters and may be obtained by requesting Research Report RR:C09-1028.C1064/C1064M 123(2) Revised Section 5 to require documentation of verification, list the tolerance for rejecting thermometers, clarify therequirements for a

37、 liquid bath, and change the term used from “calibration” to “verification.”ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validit

38、y of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comment

39、s are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not

40、 received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copi

41、es) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).C1064/C1064M 124