ASTM B936-2013 Standard Specification for Copper-Chromium-Iron-Titanium Alloy Plate Sheet Strip and Rolled Bar《铜铬铁钛合金板、薄板、带材和轧制棒材的标准规格》.pdf
《ASTM B936-2013 Standard Specification for Copper-Chromium-Iron-Titanium Alloy Plate Sheet Strip and Rolled Bar《铜铬铁钛合金板、薄板、带材和轧制棒材的标准规格》.pdf》由会员分享,可在线阅读,更多相关《ASTM B936-2013 Standard Specification for Copper-Chromium-Iron-Titanium Alloy Plate Sheet Strip and Rolled Bar《铜铬铁钛合金板、薄板、带材和轧制棒材的标准规格》.pdf(6页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: B936 08B936 13Standard Specification forCopper-Chromium-Iron-Titanium Alloy Plate, Sheet, Stripand Rolled Bar1This standard is issued under the fixed designation B936; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, th
2、e year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification establishes the requirements for Copper Alloy UNS No. C18080 for plate, sheet, strip, an
3、d rolled bar inalloy.bar.NOTE 1Since CopperAlloy UNS No. C18080 is frequently used in a variety of applications where yield strength and stress-corrosion resistance maybe critical, it is recommended that drawings or samples of the part to be fabricated and details of application be submitted for use
4、 in establishing temperand treatment of material.NOTE 2Copper Alloy UNS No. C18080 is covered by a patent. Interested parties are invited to submit information regarding the identification of analternative(s) to this patented item toASTM International headquarters. Your comments will receive careful
5、 consideration at a meeting of the responsibletechnical committee,1 which you may attend.1.2 UnitsThe values stated in inch-pound units are to be regarded as standard. The values given in parentheses aremathematical conversions to SI units that are provided for information only and are not considere
6、d standard.2. Referenced Documents2.1 The following documents of the issue in effect on the date of material purchase form a part of this specification to the extentreferenced herein:2.1 ASTM Standards:2B248 Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Str
7、ip, and Rolled BarB248M Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar(Metric)B601B846 Classification for Temper Designations for Terminology for Copper and Copper AlloysWrought and CastAlloysB846B950 Terminology for Guide for Editorial
8、 Procedures and Form of Product Specifications for Copper and Copper AlloysE8/E8M Test Methods for Tension Testing of Metallic MaterialsE62 Test Methods for Chemical Analysis of Copper and Copper Alloys (Photometric Methods) (Withdrawn 2010)3E76 Test Methods for Chemical Analysis of Nickel-Copper Al
9、loys (Withdrawn 2003)3E255 Practice for Sampling Copper and Copper Alloys for the Determination of Chemical CompositionE478 Test Methods for Chemical Analysis of Copper AlloysE1473 Test Methods for Chemical Analysis of Nickel, Cobalt, and High-Temperature Alloys3. General Requirements3.1 The followi
10、ng sections of SpecificationSpecifications B248 and B248M constitute a part of this specification:3.1.1 TerminologyDefinitions,3.1.2 Materials and Manufacturing,Manufacture,3.1.3 Workmanship, Finish, and Appearance,3.1.4 Sampling, except for chemical analysis,3.1.5 Number of Tests and Retests,3.1.6
11、Specimen Preparation,1 This specification is under the jurisdiction of ASTM Committee B05 on Copper and Copper Alloys and is the direct responsibility of Subcommittee B05.01 on Plate,Sheet, and Strip.Current edition approved Oct. 1, 2008Oct. 1, 2013. Published November 2008October 2013. Originally a
12、pproved in 2004. Last previous edition approved in 20052008as B936 04B936 08.1. DOI: 10.1520/B0936-08.10.1520/B0936-13.2 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer t
13、o the standards Document Summary page on the ASTM website.3 The last approved version of this historical standard is referenced on www.astm.org.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previ
14、ous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.*A Summary of Chan
15、ges section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States13.1.7 Test Methods, except for chemical analysis,3.1.8 Significance of Numerical Limits,3.1.9 Inspection,3.1.10 Rejection and Rehearing,3.1
16、.11 Certification,3.1.12 Mill Test Reports (Mill),Report,3.1.13 Packaging and Package Marking, and3.1.14 Supplementary Requirements.3.2 In addition, when a section with a title identical to that referenced in 3.1 appears in this specification, it contains additionalrequirements which supplement thos
17、e appearing in SpecificationSpecifications B248 and B248M.4. Terminology4.1 DefinitionsFor definitions of terms used in this specification, refer to Terminology B846.5. Ordering Information5.1 Contracts or purchase orders for product under this specification should include the following information:
18、5.1.1 ASTM designation and year of issue (for example, issue,B936 XX),5.1.2 Copper Alloy UNS No. designation (for example, C18080),designation,5.1.3 Temper (see Section (Section 8),5.1.4 Dimensions, that is, thickness, width, length, and so forth edges (see Section 13),5.1.5 Form, that is, plate, sh
19、eet, strip, or rolled bar,5.1.5 How furnished, that is, coils, specific lengths or stock lengths, with or without ends, furnished: straight lengths or coils,5.1.6 Quantity, that is, total weight each form, temper, and total weight or total length or number of pieces of each size, and5.1.7 Whether ma
20、terial is purchased for agencies of the U.S. government (see Section 12).5.2 The following options are available under this specification and should be specified in the contract or purchase order whenrequired:5.2.1 Type of edge, that is, slit, sheared, sawed, square corners, round corners, rounded e
21、dges, or full rounded edges, and5.2.2 Width and straightness tolerances (see Section 13).6. Materials and Manufacture6.1 Material:6.1.1 The material of manufacture shall be a cast form (cast bar, cake, slab, and so forth, etc.) of CopperAlloy UNS No. C18080of such purity and soundness as to be suita
22、ble for process in to processing into the products prescribed herein.6.1.2 In the event When specified in the contract or purchase order that heat identification or traceability is required, thepurchaser shall specify the details desired.NOTE 3Due to the discontinuous nature of the processing of cas
23、tings into wrought products, it is not always practical to identify a specific castinganalysis with a specific quantity of finished material.6.2 Manufacture:6.2.1 The product shall be manufactured by such hot working, cold working, and annealing processes as to produce a uniformwrought structure in
24、the finished product.6.2.2 The product shall be hot-hot or cold-worked cold worked to the finished size and subsequently annealed,annealed whenrequired, to meet the temper properties specified.6.2.3 EdgesSlit edges shall be furnished unless otherwise specified in the contract or purchase order.7. Ch
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMB9362013STANDARDSPECIFICATIONFORCOPPERCHROMIUMIRONTITANIUMALLOYPLATESHEETSTRIPANDROLLEDBAR 铜铬铁 钛合金

链接地址:http://www.mydoc123.com/p-462841.html