ASTM A960 A960M-2007 Standard Specification for Common Requirements for Wrought Steel Piping Fittings.pdf
《ASTM A960 A960M-2007 Standard Specification for Common Requirements for Wrought Steel Piping Fittings.pdf》由会员分享,可在线阅读,更多相关《ASTM A960 A960M-2007 Standard Specification for Common Requirements for Wrought Steel Piping Fittings.pdf(9页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: A 960/A 960M 07Standard Specification forCommon Requirements for Wrought Steel Piping Fittings1This standard is issued under the fixed designationA 960/A 960M; the number immediately following the designation indicates the yearof original adoption or, in the case of revision, the year o
2、f last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification covers a group of common require-ments that shall apply to wrought steel piping fittings covere
3、din any of the following individual product specifications or anyother ASTM specification that invokes this specification orportions thereof:Title of Specification ASTMDesignationSpecification for Piping Fittings of WroughtCarbon Steel and Alloy Steel for Moderate andElevated TemperaturesA 234/A 234
4、MSpecification for Wrought Austenitic StainlessSteel Piping FittingsA 403/A 403MSpecification for Piping Fittings of Wrought CarbonSteel and Alloy Steel for Low-Temperature ServiceA 420/A 420MSpecification for Butt-Welding, Wrought-CarbonSteel, Piping Fittings with Improved Notch ToughnessA 758/A 75
5、8MSpecification for As-Welded Wrought AusteniticStainless Steel Fittings for General CorrosiveService at Low and Moderate TemperaturesA 774/A 774MSpecification for Wrought Ferritic, Ferritic/Austenitic,and Martensitic Stainless Steel Piping FittingsA 815/A 815MSpecification for Heat-Treated Carbon S
6、teelFittings for Low-Temperature and Corrosive ServiceA 858/A 858MSpecification for Wrought High-StrengthLow-Alloy Steel Butt-Welded FittingsA 860/A 860M1.2 In case of conflict between a requirement of the indi-vidual product specification and a requirement of this generalrequirement specification,
7、the requirements of the individualproduct specification shall prevail over those of this specifica-tion.1.3 By mutual agreement between the purchaser and thesupplier, additional requirements may be specified (See 4.1.7).The acceptance of any such additional requirements shall bedependent on negotiat
8、ions with the supplier and must beincluded in the order as agreed upon by the purchaser andsupplier.1.4 The values stated in either inch-pound units or SI unitsmetric are to be regarded separately as standard. Within thetext and the tables, the SI units are shown in brackets. Thevalues stated in eac
9、h system are not exact equivalents; there-fore each system must be used independently of the other.Combining values from the two systems may result in noncon-formance with the specification. The inch-pound units shallapply unless the “M” designation SI of the product specifi-cation is specified in t
10、he order.2. Referenced Documents2.1 ASTM Standards:2A 29/A 29M Specification for Steel Bars, Carbon andAlloy,Hot-Wrought, General Requirements forA 234/A 234M Specification for Piping Fittings of WroughtCarbon Steel and Alloy Steel for Moderate and HighTemperature ServiceA 262 Practices for Detectin
11、g Susceptibility to Intergranu-lar Attack in Austenitic Stainless SteelsA 370 Test Methods and Definitions for Mechanical Testingof Steel ProductsA 388/A 388M Practice for Ultrasonic Examination ofHeavy Steel ForgingsA 403/A 403M Specification for Wrought Austenitic Stain-less Steel Piping FittingsA
12、 420/A 420M Specification for Piping Fittings of WroughtCarbon Steel and Alloy Steel for Low-Temperature Ser-viceA 700 Practices for Packaging, Marking, and LoadingMethods for Steel Products for ShipmentA 751 Test Methods, Practices, and Terminology forChemical Analysis of Steel ProductsA 758/A 758M
13、 Specification for Wrought-Carbon SteelButt-Welding Piping Fittings with Improved Notch Tough-nessA 763 Practices for Detecting Susceptibility to Intergranu-lar Attack in Ferritic Stainless SteelsA 774/A 774M Specification for As-Welded Wrought Aus-tenitic Stainless Steel Fittings for General Corros
14、ive Ser-vice at Low and Moderate TemperaturesA 815/A 815M Specification for Wrought Ferritic, Ferritic/Austenitic, and Martensitic Stainless Steel Piping FittingsA 858/A 858M Specification for Heat-Treated Carbon SteelFittings for Low-Temperature and Corrosive Service1This specification is under the
15、 jurisdiction of ASTM Committee A01 on Steel,Stainless Steel and Related Alloys and is the direct responsibility of SubcommitteeA01.22 on Steel Forgings and Wrought Fittings for Piping Applications and BoltingMaterials for Piping and Special Purpose Applications.Current edition approved Feb. 1, 2007
16、. Published February 2007. Originallyapproved in 1996. Last previous edition approved in 2006 as A 960/A 960M06.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the
17、standards Document Summary page onthe ASTM website.1*A Summary of Changes section appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.A 860/A 860M Specification for Wrought High-StrengthLow-Alloy Steel
18、Butt-Welding FittingsA 941 Terminology Relating to Steel, Stainless Steel, Re-lated Alloys, and FerroalloysA 967 Specification for Chemical Passivation Treatmentsfor Stainless Steel PartsE 165 Test Method for Liquid Penetrant ExaminationE 213 Practice for Ultrasonic Examination of Metal Pipeand Tubi
19、ngE 709 Guide for Magnetic Particle ExaminationE 1916 Guide for Identification and/or Segregation ofMixed Lots of Metals2.2 Military Standard:3MIL-STD-163 Steel Mill Products, Preparation for Ship-ment and Storage2.3 Manufacturers Standardization Society Standards:4MSS-SP-25 The Standard Marking Sys
20、tem of Valves,Fittings, Flanges and UnionsMSS-SP-43 Standard Practice for Light Weight StainlessSteel Butt-Welding FittingsMSS-SP-75 Specification for High Test Wrought Butt-Welding FittingsMSS-SP-79 Socket Welding Reducer InsertsMSS-SP-95 Swage(d) Nipples and Bull Plugs2.4 American Society of Nonde
21、structive Testing:5SNT-TC-1A Recommended Practice for NondestructiveTesting Personnel Qualification and Certification2.5 ASME Standards:6B16.9 Steel Butt-Welding FittingsB16.11 Forged Steel Fittings, Socket Welding and ThreadedSection IX Welding Qualifications3. Terminology3.1 Definitions of Terms S
22、pecific to This Standard:3.1.1 bara solid section that is long in relationship to itscross sectional dimensions, with a relatively constant crosssection throughout its length. (See Specification A 29/A 29Mfor definitions relating to the production of hot wrought andcold finished bars.)3.1.2 certifyi
23、ng organizationthe company or associationresponsible for the conformance of, the marking of, and thecertification of the product to the specification requirements.3.1.3 fittinga component for non-bolted joints used inpiping systems and pressure vessels.3.1.4 flangea component for bolted joints used
24、in pipingsystems and pressure vessels.3.1.5 forgingthe product of a substantially compressivehot or cold plastic working operation that consolidates thematerial and produces the required shape.3.1.6 DiscussionThe plastic working must be performedby a forging machine, such as a hammer, press, or ring
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMA960A960M2007STANDARDSPECIFICATIONFORCOMMONREQUIREMENTSFORWROUGHTSTEELPIPINGFITTINGSPDF

链接地址:http://www.mydoc123.com/p-460123.html