ARMY MIL-T-46938 C-1994 TETRACENE《并四苯》.pdf

《ARMY MIL-T-46938 C-1994 TETRACENE《并四苯》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-T-46938 C-1994 TETRACENE《并四苯》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、 MIL-T-46938C = 9999906 1978812 152 INCH-POUND MIL-T-46938C (AR) SUPERSEDING MIL-T-46938B (AR) 26 April 1985 - MILITARY SPECIFICATION TETRACENE This specification is approved for use by the US Army Armament, Munitions and Chemical Command and is available for use by all Departments and Agencies of t

2、he Department of Defense. 1. SCOPE 1.1 Scope. This specification covers the requirements and quality assurance provisions for the manufacture and acceptance of tetracene (1-(5-tetrazolyl) -4-guanyl tetrazene hydrate) for use in priming compositions. (See 6.1) 2. APPLICABLE DOCUMENTS 2.1 Government d

3、ocuments. 2.1.1 Specifications, standards and handbooks. The following specifications, standards and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Sp

4、ecifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). SPECIFICATIONS FEDERAL RR-S-366 - Sieves, Standard for Testing Purposes Beneficial comments (recommendations. additions, deletions! and any pertinent data which may be of use in improving this document s

5、hould be addressed to: Commander, U.S. Army ARDEC ATTN: SMCAR-BAC-S, Picatinny Arsenal, New Jersey 07806-5000 by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. FSC - 1376 AMSC/NA DISTRIBUTION STATEMENT A. Approved for public

6、 release: distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-46938C 9999906 1978813 O99 = MIL-T-46938C (AR) MILITARY MIL-A-48078 - Ammunition, Standard Quality Assurance Provisions, General Specification for STANDARDS MI

7、L I TARY MIL-STD-109 - Quality Assurance Terms and Definitions MIL-STD-129-1 - Marking for Shipment and Storage - Ammunition and Explosives Inspection and Testing MIL-STD-650 - Explosive: Sampling MIL-STD-1168 - Lot Numbering of Ammunition MIL-STD-1218 - ACS Chemicals MIL-STD-2073-1 - DOD Material P

8、rocedures for Development and Application of Packaging Requirements (Unless otherwise indicated, copies of federal and military specifications, standards, and handbooks are available from DODSSP - Customer Service, Standardization Documents Order Desk, 700 Robbins Avenue, Bldg. 4D, Philadelphia, PA

9、19111-5094.) 2.1.2 Other Government documents, drawinqs and publications. The following other Government documents, drawings publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues are those cited in the solicitation. CODE OF FEDERAL REGULATIO

10、NS 49 CFR 100-180 - Department of Transportation Rules and Regulations for the Transportation of Hazardous Mat erial s DI-PACK-81059 - Data Item Description Vanderkamp Apparat us - Scientific Glass Apparatus 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from

11、IHS-,-,-, MIL-T-46938C (AR) U.N. Document ST/SG/AC.10.11 - United Nations Committee of Experts on the Transportation of Dangerous Goods ICA0 - International Civil Aviation Organization IMDG Code - Intergovernmental Maritime Organizations International Maritime Dangerous Goods Code (The Interstate Co

12、mmerce Commission Regulation are now a part of the Code of Federal Regulations, available from the Superintendent of Documents, US Government Printing Office, Washington, DC 20402. Orders for the above publications should cite, “49 CFR 100-180 (latest revision) I .) 2.2 Non-Government publications.

13、The following document(s) form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DoD adopted are those listed in the issue of the DODISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed i

14、n the DODISS are the issues of the documents cited in the solicitation (see 6.2). AMERICAN SOCIETY FOR TESTING AND MATERIALS ASTM D2905 - Statements on Number of Specimens Required to Determine the Average Quality of a Textile Material ASTM E300 - Sampling Industrial Chemicals (Application for copie

15、s should be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103). 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein the text of this document takes precedence. Nothing in this docume

16、nt, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. (See Contract Provisions for additional precedence criteria). 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NIL-T-46938C m 9999906 1978815 961

17、3. REQUIREMENTS 3.1 Material. Tetracene shall be manufactured by any method which will produce material conforming to the requirements of this specification 3.2 Chemical and physical requirements. Tetracene shall comply with the chemical and physical requirements specified in Table I when tested as

18、specified in the applicable paragraphs cited in 4.5. TABLE I. Characteristics Color and appearance Melting and explosion point Granulation Speci fic gravity Heavy metals Nitrogen content Physical and chemical characteristics. Requirement Test method White to pale Para 4.5.2 yellow 127O +. 3OC Para 4

19、.5.3 100% through US Para 4.5.4 #45 Sieve 1.65 i 0.05 Para 4.5.5 None Para 4.5.6 74.5 2 1.0% Para 4.5.7 3.3 First article. When specified in the contract or purchase order (see 6.2), a sample shall be subjected to first article inspection (see 6.3) in accordance with the technical provisions herein

20、(see 4.3). 3.4 Workmanship. The manufacturer shall implement procedures and controls to assure that the process and the product are not compromised by foreign materials and contaminants or any other conditions which may degrade the composition. Determination of foreign materials shall be in accordan

21、ce with 4.5.8. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance of all inspection requirements (examinations and tests) as specified herein. Except as 4 Provided by IHSNo

22、t for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-46938C M 9997906 L3788Lb T8 MIL-T-46938C (AR) otherwise specified in the contract or purchase order, the contractor may use his own or any other facilities suitable for the performance of the inspection requiremen

23、ts specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in this specification where such inspections are deemed necessary to ensure supplies and services conform to prescribed requirements. 4.1.1 Responsibility for comp

24、liance. All items shall meet all requirements of sections 3 and 5. The inspection set forth in this specification shall become a part of the contractors overall inspection system or quality program. The absence of any inspection requirements in the specification shall not relieve the contractor of t

25、he responsibility of ensuring that all products or supplies submitted to the Government for acceptance comply with all requirements of the contract. Sampling inspection, as part of manufacturing operations, is an acceptable practice to ascertain conformance to requirements; however, this does not au

26、thorize submission of known defective material, either indicated or actual, nor does it commit the Government to accept defective material. 4.1.2 General provisions. Unless otherwise specified herein, the provisions of MIL-A-48078 apply and form a part of this specification. Reference shall be made

27、to MIL-STD-109 to define quality assurance terms used herein. 4.2 Classification of inspections. The required inspections specified herein are classified as follows: a. First article inspection (see 4.3) b. Quality conformance inspection (see 4.4) 4.3 First article inspection. 4.3.1 Submission. When

28、 specified in the contract or purchase order, the contractor shall submit a first article sample consisting of one (1) pound of tetracene. The first article sample shall be obtained from the first production lot which has been produced by the contractor, using the same production processes, procedur

29、es and equipment as will be used in fulfilling the contract. All raw materials used in producing the tetracene shall be from the same sources as will be used in regular production. 4.3.2 InsDections to be performed. The first article sample may be subjected by the Government to any or all of the exa

30、minations or tests specified herein. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-JJ -ri e: w E 3 z W m H 8 n $3 h2 MIL-T-46938C 9999906 1978817 734 in id a a O JJ k O -ri k a I) u -rl JJ I) -ri k o ci u a k w u w Lri W i3 n 2 E x z i2 z a v) z

31、H k O v; o H w E z E 2 w I: o u C a k a a, A a a a F: a k O 4 O u 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-46938C (AR) 4.3.3 Rejection. If the sample fails to comply with any of the applicable requirements, the first article quantity s

32、hall be rejected. The Government reserves the right to terminate its inspection upon any failure of a sample to comply with any of the stated requirements. 4.4 puality conformance inspection. 4.4.1 Inspection lot formation. A lot shall consist of one or more batches of tetracene produced by one manu

33、facturer, in accordance with the same specification, or same specification revision, under one continuous set of operating conditions. Each batch shall consist of that quantity of tetracene that has been subjected to the same unit chemical or physical process intended to make the final product homog

34、eneous. The criteria and procedure for the assignment of lot numbers shall be in accordance with MIL-STD-1168. 4.4.2 Examinations and tests. a. Classification of characteristics. Quality conformance examinations and tests are specified in the following Classification of Characteristics paragraphs. T

35、he contractors quality program or detailed inspection system shall provide assurance of compliance of all characteristics with the applicable specification requirements utilizing as a minimum the conformance criteria specified herein. b. Alternative quality conformance provisions. Unless otherwise s

36、pecified herein or provided for in the contract, alternative quality conformance procedures, methods, or equipment, such as statistical process control, tool control, other types of sampling procedures, etc., may be used by the contractor when they provide, as a minimum, the level of quality assuran

37、ce required by the provisions specified herein. Prior to applying such alternative procedures, methods, or equipment, the contractor shall describe them in a written proposal submitted to the Government for evaluation (see 6.7). When required, the contractor shall demonstrate that the effectiveness

38、of each proposed alternative is equal to or better than the specified quality assurance provision(s) herein. In cases of dispute as to whether the contractors proposed alternative(s1 provides equivalent assurance, the provisions of this specification shall apply. All approved alternative provisions

39、shall be specifically incorporated into the contractors quality program or detailed inspection system, as applicable. 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-46938C = 999990b 197819 507 m u -rl lJ m -rl k a, lJ u a k (d A u rl a u -4

40、rn h a a d a rl (u u r( P-JNNNNCY * mmmmmm m mmmmmm N mmmmmm m *dcd -4 -4* -4 c O .rl JJ -rl m O x c -rl w a, a a, c k a a, a a a a c (d k O rl O u h L, -rl a k br u -rl u -4 u 0 a VI m 4 (d JJ E 9 a a, X L, c a, L, c O a u *rl A c Ul a, c lJ k gi3 k 3 -rl z O m 3 x u S 2 C u C 3 n D 0 4 z, + 3 . n

41、-i m U + a % ! ! i I I 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-Yb938C = 9999906 1978820 229 MIL-T-46938C (AR) 4.4.3 Testinq. PRECAUTION: This specification covers sampling and testing of toxic and hazardous material. Accordingly, it i

42、s emphasized that all applicable safety rules, regulations and procedures must be followed in handling and processing. 4.4.3.1 Samplinq. Obtain two random 30 gm samples from each batch of tetracene being submitted for inclusion in a lot. The samples shall be obtained from the process vessel prior to

43、 packout using procedures described in ASTM-E300 for slurries. 4.4.3.2 Testinq for batch acceptance. One sample obtained according to 4.4.3.1 from each batch shall be tested in accordance with the applicable test methods of 4.5 for conformance with the requirements for color and appearance (see 3.2)

44、, and workmanship (see 3.4). If any sample fails to meet any of these requirements, the batch represented by the sample shall be rejected. Rework of non-conforming batches is permitted. 4.4.3.3 Testinq for lot acceptance, The second samples from the batches not rejected under the provisions of 4.4.3

45、.2 shall be placed in a suitable container of sufficient volume to hold a composite sample from all batches in the lot. The tetracene batches shall be thoroughly mixed to assure homogeneity, and two sub-samples of approximately 30 gm each shall be obtained from this composite sample. Both sub-sample

46、s shall be tested in accordance with the applicable test methods of 4.5 to determine conformance with the requirements given in 3.2, Table I for melting and explosion points, granulation, specific gravity, presence of heavy metals and nitrogen content. If either sub-sample fails to meet any of the r

47、equirements, the lot represented by the composite sample shall be rejected. 4.4.4 Inspection equipment. For the performance of all test and examinations specified in 4.3 and 4.4, the equipment specified shall be employed. The contractor shall have the equipment available, utilize it in accordance wi

48、th the test method, and is responsible to assure that it is properly calibrated. Government approval of all contractor designed inspection equipment is required prior to its use for acceptance testing (see 6.4). 4.5 Methods of inspection. All tests described in this section shall be performed using

49、prescribed procedures for replicate determination given in standard analytical chemistry textbooks or ASTM D 2905. Unless otherwise specified herein, all chemicals shall be Reagent Grade or ACS Grade in accordance with 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-4673BC 9799906 L97B2L Lb5 MIL-T-46938C (AR) MIL-STD-1218. If