ARMY MIL-D-51453 A-1986 DISPERSER RIOT CONTROL AGENT PORTABLE 3 GALLON M33A1《M33A1 3加仑便携式催泪弹分散机》.pdf

《ARMY MIL-D-51453 A-1986 DISPERSER RIOT CONTROL AGENT PORTABLE 3 GALLON M33A1《M33A1 3加仑便携式催泪弹分散机》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-D-51453 A-1986 DISPERSER RIOT CONTROL AGENT PORTABLE 3 GALLON M33A1《M33A1 3加仑便携式催泪弹分散机》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、:-y= Q MIL-D-51453A 10 7799906 0334325 7 m _c -37. a MIL-D-5 i4 5 3A( EA) 16 January 1986 SUPERSEDING MIL-D-51453 (EA) 21 May 19-79 MILITARY SPECIFICATION DISPERSER, RIOT CONTROL AGENT, PORTABLE, 3 GALLON, M33A1 This specification is approved for use within U.S4 Army Chemical Research and Developmen

2、t Center, Department of the Army, and is available for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers one type of disperser. 2. APPLICABLE DOCUMENTS 2 . 1 Government documents . - 2.1.1 Specifications and standards. The following speci

3、fications and stan- dards form a part of this specification to the extent specified herein. Unless otherwise specified, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the so

4、licitation. SPECIFICATIONS FEDERAL PPP-B-26 - Bag , Plastic , (General Purpose) . PPP-B-636 - Boxes, Shipping, Fiberboard. PPP-C-1120 - Cushioning Material, Uncompressed Bound Fiber, for Packaging. PPP-F-320 - Fiberboard: Corrugated and Solid, Sheet Stock (Container Grade) and Cut Shapes. PPP-P-291

5、- Paperboard, Wrapping and Cushioning . PPP-T-76 - Tape, Packaging, Paper (For Carton Sealing). : Beneficial comments (recommendations, additions, deletions) and any perti- : : nent data which may be of use in improving this document should be addressed: : to: Commander, U.S. Army Chemical Research

6、and Development Center, ATTN: : SMCCR-SPD-TS, Aberdeen Proving Ground, MD 21010-5423 by using the self- : addressed Standardization Document Improvement Proposal (DD Form 1426) 1 : appearing at the end of this document or by letter. AMSC NfA FSC 1040 DISTRIBUTION STATEMENT A. Approved for public rel

7、ease; distribution is unlimited. . THIS DOCUMENT CONTAINS 16 PAGES. . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-flIL-D-5L453A LO M 9999706 0334326 9 MIL-D-5 14 53A( EX) MILITARY MIL-P-116 - Preservation, Methods of. MIL-E-117 - Bags, Sleeves an

8、d Tubing - Interior Packaging. MIL-E-2427 - Box, Ammunition Packing; Wood, Nailed. MIL-C-5501/7 - Caps and Plugs, Protective, Dust and Moisture Seal (Cap-Plug , General Purpose) STANDARDS FEDERAL FED-STD-751 - Stitches, Seams and Stitchings. MILITARY MIL-STD-10: - Sampling Procedures and Tables for

9、Inspection by Attribut es . MIL-STD-129 - Marking for Shipment and Storage. MIL-STD-147 MIL-STD-1168 - Ammunition Lot Numbering. - Palletized and Containerized Unit Loads 40 Inch Pallets , Skids, Runners or Pallet Type Base. 2.1.2 Other Government documents and drawings. The following other Govern-

10、ment documents and drawings form a part of this Specification to the extent specified herein. Unless otherwise specified, the issues shall be those in effect on the date of the solicitation. DRAWINGS AND TECHNICAL, DATA PACKAGE LIST (TDPL) U.S. AM ARMAMENT, MUNITIONS AND CHEMICAL COMMAND CHEMICAL RE

11、SEARCH AND DEVELOPMENT CENTER TDPL 116-3-121 - Disperser, Riot Control Agent, Portable, 3 Gallon, M33A1 (Copies of specifications, standards, drawings and other Government documents required by contractors in connection with specific acquisition functions should be obtained from the contracting acti

12、vity or as directed by the contract- ing activity.) 2.2 Order of precedence. In the event of a conflict between the text of this specification and the references cited herein ( except for associated detail specifications, specification sheets or MS standards), the text of this specification shall ta

13、ke precedence. Nothing in this specification, however, shall supersede applicable laws and regulations unless a specific exemption has been obtained. ? . 4 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-D-51453A 10 W 7779706 0334127 O m a * e

14、 3. REQUIREMENTS 3.1 Materials and components. 3.1.1 Materials. All materials cited on TDPL ii6-3-i2i or on the subsidiary drawings shall conform to the specifications listed thereon or to the specific characteristics set forth on the drawings. 3.1.2 Components. All components of the disperser shall

15、 conform to the specifications and drawings listed on TDPL 116-3-121 and on subsidiary draw- ings 3.2 Assembly. The disperser shall be assembled as shown -on Drawing 116-3-121. 3.3 Functioning. When the high pressure cylinder is charged to 2100 + 100 pounds per square inch gage (psig), the regulator

16、 shall deliver air at 180 + 20 psig, the gun shall function freely, and the assembly shall not leak when tested in accordance with 4.4.4.1. - 3 .4 Container (Drawing 116-3-101 1 . 3.4.1 Leakage and deformation. The container shall not leak or be perma- nently deformed when subjected to a minimum hyd

17、rostatic pressure of 350 psig for 1 minute when tested in accordance with 4.4.4.2. 3.4.2 Rupture. The container chal not rupture prior to sustaining a mini- mum hydrostatic pressure of 800 psig when tested in accordance with 4.4.4.3. 3.5 - Gun. The gun shall function freely and not leak for a minimu

18、m period of 30 seconds when subjected to a minimum bdrostatic or air pressure of 200 psig when tested in accordance with 4.4.4.4. 3.6 Container assembly. The container assembly shall not leak at a minimum air pressure of 200 psig when tested in accordance with 4.4.4.5. 3.7 Harness. 3.7.1 Stitching.

19、All stitching, except bartacking, shall be stitch type 301 or 401 of FED-STD-751, 8 to 10 stitches per inch. 3.7.1.1 Typ e 301 stitching. Ehds of all stitching shall be backstitched 1 inch minimum (1/2 inch on box X and W-W stitching) , except where ends are turned under in a hem or held down by oth

20、er stitching. maintained so that there will be no loose or tight stitching, and the lock shall be embedded in the inaterials sewn. Thread tension shall be 3.7.1.1.1 Repairs of type 301 stitching. Repairs of type 301 stitching shall be as follows: 3 Provided by IHSNot for ResaleNo reproduction or net

21、working permitted without license from IHS-,-,-MIL-D-5L453A LO M 7977706 0334228 2 MIL-D-51453A( EA) (a) When thread breaks or bobbin run-outs occur during sewing, the stitching shall be repaired by restarting the stitching a minimum of one inch (1/2 inch for box X and W-W stitching) back of the end

22、 of the stitching.l/ (b) Thread breaks, or two or more consecutive skipped stitches or run-Offs, noted during inspection of the item (in-process or end item) shall be repaired by overstitching. The stitching shall start a minimum of one inch in back of the defective area (1/2 inch on box X and W-W s

23、titching), continue over the defective area and continue a minimum of one inch beyond the defective area onto the existing stitching. Loose or excessively tight stitching shall be repaired by removing the defective stitching, without damaging the materials, and restitching in the required manner.l/

24、Lhhen making the above repairs the ends of the stitching are not required to be backstitched. 3.7.1.2 Type 401 stitching. Thread tension shall be maintained so that there will be no loose stitching. Al1 repairs shall be in accordance with 3.7.1.1*1(a) and 3.7.1.1.1(b) except substitute 3/4 inch for

25、one inch wherever one inch appears. 3.7.1.3 Automatic stitching. Automatic machines may be used to perform any of the required stitch patterns provided the requirements for the stitch pat- tern, stitches per inch, size and type of thread are met, and at least three or more tying, overlapping, or bac

26、k stitches are used to secure the ends of the stitching. 3.7.1.4 Lubrication of thread. There shall be no lubrication of the thread by any means, prior to or during sewing. 3.7.1.5 Thread ends. All thread ends shall be trimmed to i/4 inch maximum length. 3.7.2 Location marks. Location and notice mar

27、ks shall not be drilled. 3.7.3 Snap fasteners and rivets. The lengths of the rivets and fasteners shall be determined by the contractor and shall effect a secure clinch of the assembled component s. 3.7.3.1 Setting. The hole shall be punched before inserting the fastener or rivet and shall be smalle

28、r than the outside diameter of the fastener barrel or rivet so that it must be forced through the hole. The fastener or rivet shall be securely clinched without cutting the surrounding material. When installed, the clinched end shall have a uniform roll that will effect a secure hold. All burrs shal

29、l be removed from the rivet. 3.7.4 Repairs. Repairs such as mends, darns, patches or splices are not per- mitted on the harness. 4 ,. .-,: 1-24 - . . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-D-51453A LO 997790b 0334327 4 W MIL-D-5 14 53A(

30、EA) 4.3 Preproduction inspection. 3.8 Frame and frame assembly riveting. Final sizing of rivet holes shall be done at assembly to preclude misalignment of mating holes at time of assembly. Punching of rivet holes in tubular components shall not be permitted. surfaces of riveted components shall be d

31、rawn tight with the rivet head in con- tact with its mating surface. and sharp edges. Mating The cet rivets shall be free of splits, burrs, 3.9 Preproduction. Prior to the start of regular production, a preproduc- tion sample of dispersers and components shall be produced for examination and tests i

32、n accordance with this specification. 3.10 Workmanship. The disperser and components shall be free from damage, cracks, splits, tears, burrs, sharp edges, sharp corners and foreign matter such as dirt, grease or oil that could impair their intended use. 4 . QUALITY ASSURANCE PROVISIONS 4.1 Responsib

33、ility for inspection. Unless otherwise specified in the con- tract or purchase order, the contractor is responsible for the performance of all inspection requirements as specified herein. in %he contract or purchase order, the contractor may use his own or any other facilities suitable for the perfo

34、rmance of the inspection requirements speci- fied herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to prescribed require

35、ments. Except as otherwise specified 4.1.1 Responsibility for compliance. All items must meet all requirements of sections 3 and 5. a part of the contractors overall inspection system or quality program. The absence of any inspection requirements in the specification shall not relieve the contractor

36、 of the responsibility of assuring that all products or supplies submitted to the Government for acceptance comply with all requirements of the con-bract. Sampling in quality conformance does not authorize submission of known defective material, either indicated or actual, nor does it commit the Gov

37、ernment to acceptance of defective material. The inspection set forth in this specification shall become 4.2 Classification of inspections. The inspection requirements specified herein are classified as follows: (a) (b) Preproduction inspection (see 4.3) Quality conformance inspection (see 4.4) . 4.

38、3.1 - Lot. A preproduction sample of five assembled dispersers, 38 con- tainers and five guns shall be manufactured using the same methods, materials, equipment, and processes as will be used during regular production. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without li

39、cense from IHS-,-,-MIL-D-SLV53A LO 7777706 03341130 O MI L-D-514 5 3A( EA) 4.3.2 Inspection procedure, 4.3.2.1 For nondestructive tests. The assembled dispersers shall be tested in accordance with 4.4.kc. The containers shall be tested in accordance with 4.4.4.2. The guns shall be tested in accordan

40、ce with 4.4.4.4. 4.3.2.2 For destructive tests. Twenty-two containers shall be tested in accordance with 4.4.4.3. teen containers shall be tested in accordance wth 4.4.4,3. If one container fails the test, the remaining six- 4.3.3 Acceptance/rejection critepia. The preproducton sample shall comply w

41、ith 4.3.2.1 and 4.3.22 to be acceptable except for the containers. more containers fall the test the entire sample of containers shall be destroyed* The contractor shall obtain written approval from the contracting activity prior to proceedng with regular production. If two or 4.4 Quality conformanc

42、e inspection. 4.4.1 Lotting. A lot of dispersers shall be identified and controlled in accordance with MIL-STD-1168, produced by one manufacturer from the same mate- rials and under essentially the same manufacturing conditions, However, for rupture test, a lot. shall consist of 200 consecutively ma

43、nufactured containers of one interfix numberc 4.4,2 Sampling. 4.4.2.1 For examination and nondestructive tests. Sampling shall be con- ducted in accordance with MIL-STD-105. 4.4.2.2 For destructive test. One container shall be taken at random from each lot. 4.4.3 Inspection procedures. 4.4.3.1 For e

44、xamination and nondestructive test. The disperser and the level A packaging shall be examined in accordance with the classification of defects and with MIL-STD-105. Each assembled disperser shall be tested in accordance with 4.4.4,i. All defective items shall je removed from the lot. Each gun shall

45、be tested in accordance with 4.4.4.4. 4.4.3.2 For destructve test, Each sample container shall be tested n accordance with 4.4.4.3. pressure shall be cause to rede& the entire lot from which the sample was drawn A failure of any one sample to meet the specified 4.4.3.3 Critical defects. Each cylinde

46、r and each container in the lot shall Any. cylinder or container failing to meet the specified test require- be inspected for its critical characteristics listed in the classification of defects. ments shal cause the lot to be rejected. 6 Provided by IHSNot for ResaleNo reproduction or networking pe

47、rmitted without license from IHS-,-,-MIL-D-53453A LO 7977706 0334333 2 MIL-D-51453A( EA) 4.4.3.4 Classification of defects. (a) Cylinder, compressed gas (Drawing 116-3-64 , 116-3-240) . Categories Defects Crit icai: 1 Torque incorrect 2 DOT markings missing or incorrect Major : AQL 1.0 percent defec

48、tive 101 Finish missing or incorrect (b) Container assembly (Drawing 116-3-74) . Cat egories Defects Acceptance standards Critical: None defined Ma j or : AQL 1.0 percent defective 4.4.4.5 101 Leakage (c) Frame assembly (Drawing 116-3-131) . Cat egories Defects Critical: None defined Major: 101 102

49、103 i04 105 106 107 io8 109 110 111 AC& 1.0 percent defective . Component missing, incorrect or incorrectly assembled Dimens ion ( 2 . 88 ) incorrect Dimens ion ( 6 . 88 ) incorrect Dimension ( 2 . 25 ) incorrect Dimension ( 3 .O0 ) incorrect Dimension (13.12) incorrect Angle (30“ 2 5“ ) incorrect Clamping, incorrect (use an empty agent tank and an unpressurized air cylinder to check for proper operation and snug fit) Nameplate missing or inco