ARMY MIL-C-71150-1993 CARTRIDGE 60MM PRACTICE SHORT RANGE M766 LOADING ASSEMBLING AND PACKING《 tM766型60MM炮弹近程实践的装载 组装及包装》.pdf

《ARMY MIL-C-71150-1993 CARTRIDGE 60MM PRACTICE SHORT RANGE M766 LOADING ASSEMBLING AND PACKING《 tM766型60MM炮弹近程实践的装载 组装及包装》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-C-71150-1993 CARTRIDGE 60MM PRACTICE SHORT RANGE M766 LOADING ASSEMBLING AND PACKING《 tM766型60MM炮弹近程实践的装载 组装及包装》.pdf（25页珍藏版）》请在麦多课文档分享上搜索。

1、*;.E. L. MIL-C-7IIL50 999990b LbL07 408 I INCH-POUND I MIL-C-71150 (AR) O1 November 1993 MILITARY SPECIFICATION CARTRIDGE, 60MM, PRACTICE, SHORT RANGE M766 LOADING ASSEMBLING AND PACKING This specification is approved for use by the U.S. Army Armament., Muni.tions and Chemical Command, and is availa

2、ble for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1 .1 This specif i cation covers the Loading Assembling and Packing for one type of practice mortar cartridge designated as Cartridge, 60mm Pract.ice, Short Range, M766 (see 6.1). 2. APPLICABLE DOCUMENTS 2.1 Governmen

3、t- documents. - - - 2.1.3 - Specifications - - - and standards. The following speci f ications and standards form a part of this specification to the extent specified herein. Unless otherwise specified, the issues of t-hese document-s shall be those listed in the issue of the Department. of Defense

4、Index of Specifications and Standards (DODISS) and supplement thereto, cited i.n the solicitation (see 6.2). SPECIFICATIONS M II, I TARY MIL-A-48078 - Ammunition, Standard Quality Assurance Provisions, General Speci.f icat.i.on for c 3 Beneficial comments (recommendations, additions, deletions) and

5、any pertinent data which may be of use in improving this document, should be addressed to: Commander, U.S. Army ARDEC, AT“: SMCAR-BAC-S, picatinny Arsenal, NJ 07806-5000 by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. L I

6、AMSC N/A FSC 1315 T 4, Approved for public release; distribution is unlimited. O Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NIL-C-7LLSO 0b L9bL08 344 MIL-C-713 50 (AR) STANDARDS M IL I TARY MIL-STD-I O9 - Qual i ty Assurance Terms and Def i nit-

7、ions (Unless otherwise indicat-ed, copies of federal and military specifications, standards and handbooks are available from t.he DODSSP - Customer Service, Standardization Documents Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19113-5094.) 2. I .2 Other Government. documents, drawi

8、ngs, and publications. - The following other Government documents, drawingsand publications form a part- of the speci.fication to the extent speci.fied herein. Unless otherwise specified, the i.ssues shall be those in effect on the date of the soljcitat-ion. DRAWINGS (See 6.5) U.S. ARMY ARMAMENT, RE

9、SEARCH, DEVELOPMENT AND ENGINEERING CENTER (ARDEC) PRODUCT DRAWINGS I2953564 - Cartridge, 60mm: Practice, Short Range, M766 w/ Fuze, Practice, M779 PACKAGING DRAWINGS 12953578 - Packing and Marking of Container Ammunition, Fiber PAI59, for Cartridge, 60MM, Practice, Short Range, M766 for Cart-ridge,

10、 60MM, Practice, Short Range, M766 3 2953579 - Packing and Marking of Box, Wirebound, INSPECTION EQUIPMENT DRAWINGS 7256283 - Al i.gnment Check 7256348 - Profile and Alignment Gage QUALITY ASSURANCE PROVISIONS QAP Cl2961001 - Dud Plug (Copies of drawings and publicat ions and other Government docume

11、nts required by contractors in connection with specific acquisition funct-ions should be obtained from the contracting activit.y or as directed by the contracting officer.) 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-2.2 Ordl text of this - O M

12、IL-C-7LLSO 0b Lb109 280 MIL-C-71150 (AR) r of precedence. In the? event of conflict bet1 n the document and the references cited herein, the text of this document shall take precedence, Nothing in this document, however, supercedes applicable laws and regulations unless a specific exemption has been

13、 obtained. (See contract provisions for additional precedence criteria). 3. REQUIREMENTS 3.1 Material. Materials and parts shall be in accordance with applicable specifications, drawings, and this specification. 3.2 Cartridge. The cartridge shall comply with all requirements specified on (dwg) 12953

14、564 and associated drawings and with all requirements specified in applicable standards and specifications. 3.3 Detailed cartridge requirements. The cartridge shall comply with the following requirements: 3.3.1 Profile and alignment. The cartridge shall be properly assembled to successfully pass thr

15、ough a profile and alignment gage. (dwg. 7256348). 3.3.2 Obturating ring, The obtrating ring shall be present 0 and properly seated flush or below. 3.3.3 Breech Plug firing pin position. The firing pin shall be below flush relative to the rear face of the breech plug after assembly against the prope

16、lling charge. 3.3.4 Fuze Striker arming indicator marking. The red arming indicator marking on the forward section of the fuze striker shall not- be visible when the striker is in the safe position and shall be readily visible when the striker is in the armed position. 3.3.5 Increment plug. The incr

17、ement plug shall be able to be easily inserted and be firmly seated in the increment plug hole of the projecti le body, and be removable with an outward pull of 14 + 8 pounds on the increment plug pull tab when pulled perbendicular to the projectile body. 3.3.6 Torque. Each cartridge shall meet all

18、torque requirements as specified on the cartridge or subassembly drawing, 3.3.7 Dud plugs 3.3.7.1 Confi.guration, Three dud plugs shall be present and properly inserted into the projectile body. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C

19、-71350 D 9939906 3969330 TT2 = . u* MIL-Ci-71150 (AR) 3.3.7.2 Compliance. The dud plugs shall comply with the requirements of QAP Cl2961003 . The contractor shall certify to that compliance in one of the following ways: a. Inconiing inspections and test-inq in accordance with the QAP were performed

20、in his facilities, b. Incoming inspectpions and t.est.ing in accordance with the QAP were performed at. another facility approved by %he Govern nien t. c. The dud plugs were purchased with the QAP as part. of the procurement documentation, d. The QAP may be applied to the contractor that. packs out-

21、 the M776 Cartridge. In this case, the dud plugs shall be found acceptable by the Government. before releasj ng t.he inspection lot- quantity to the contractor for use in pr0duct.i on. 3.4 - Proving ground test. The cartridges shall comply with the following requirements when tested in accordance wi

22、 t.h 4.4.3.1 and 4.5.1. 3.4.1 Misfires. The cartridges shall not fail t.o fire from the weapon when they are init.ially dropped into it-. 3.4.2 Short rounds No cartridges shall have a horizontal range less than 80 percent of the average horizontal range (calculated without the short rounds), 3.4.3 M

23、etal parts separation. There shall be no metal part-s separation in the gun bore or in flight. 3.4.4 Range and deflection precision. The cartridge shall have a horizontal range probable error (PEr) less than 30 meters for all zones. The probable error deflection (PEd) shall be less than 10 meters fo

24、r all zones. 3.4.5 Duds. The fuze shall function upon ground impact. of t.he cartridge. 3.4.6 Premature burst-. There shall be no burst- in the gun bore or in the first I5 meters of flight. 3.4.7 Weapon. The cartridge shall not be the cause of weapon damage . 4 Provided by IHSNot for ResaleNo reprod

25、uction or networking permitted without license from IHS-,-,-MIL-C-7LLSO m 99999Ob L9bLLL 739 m MIL-C-71150 (AR) 3.4.8 Fuze signature. The fuze when ballistically fired shall provide both a visible and audible signature at a minimum range of 550 meters from the observer. Only a visible or only an aud

26、ible sjgnature only upon impact. is not- sufficient to meet- this requirement. Visual and audio enhancement equipment shall not be used for t-his assessment. Visible is defined as flash or smoke or both flash and smoke. 3.4.9 Dud plug function. - 3.4.9.1 Functioned round. All dud plugs shall blow ou

27、t of the project-ile body upon fuze function. 3.4.9.2 Inert round. No dud plug shall exit. the projectile body during ballistic flight- or upon impact. 3.5 First. article I- . This specification makes provisjons for first- article inspection. Requirements for the submission of first article samples

28、by the contractor are specified in the contract and by 4.3 herein.(See 6.2) 3.6 Workmanship. All parts and assemblies shall be free from burrs, chips, sharp edges, cracks, unblended radii, surface defects, dirt, grease, rust., porosity, warpage, burn marks, checks, bli Sters, excess flash, corrosion

29、 products and any other foreign matt-er. Any cleaning method used shall not- be injurious to any part nor shall the parts be contaminated by the cleaning agents. Surface coating shall be continuous except. for a few slight. scratches not. exposing base material. The loadjng and assembly operations s

30、hall be performed in a thorough, workmanlike manner consistent- with the best practices of the industry. All required markings shall be neat and sharply defined. 4. QUALITY ASSURANCE: PROVISIONS 4.1 Responsibil* -_- for inspection. Unless otherwise specified - in the contract- or purchase order, the

31、 cont-ractor is responsible for the performance of al 1 inspection requirements (examinat-ions and tests) as specified herein. Except as otherwise specified in the contract- or purchase order, the contract-or may use his own or any other facilities suitable for the performance of the inspection requ

32、irements specified herein, unless disapproved by the Government. The Government reserves the right. to perform any of t-he inspections set forth in this specification where such i rispect ions are deemed necessary to ensure supplies and services conform to prescribed requirements. 5 Provided by IHSN

33、ot for ResaleNo reproduction or networking permitted without license from IHS-,-,-rIIL-C-7bLSO 9Ob LbqL12 875 D MIL-(2-71.1 50 (AR) 4.1.1 Responsibility for compliance. All items must meet. all requirements of sections 3 and 5, The inspections set forth in this specificat ion shall become a part- of

34、 the contract-ors overall inspection system or quality program. The absence of any inspection requirements in the specification shall not. relieve the contractor of the responsibility of ensuring that all products or supplies submitted to the Government for acceptance comply with all requirements of

35、 the contract. Sampling inspection, as part of manufacturing operations, is an acceptable practice to ascertain conformance to requirements, however this does not authorize submission of known defective material , either indicated or actual , nor does it commit the Government to accept defective mat

36、erial. 4.1.2 General Provisions. The requirements of MIL-A-48078 form a part of the quality assurance provisions of this specification. Reference shall be made to MIL-STD-I09 to define quality assurance terms used herein. 4.2 Classification of inspection. The following types of inspections shall be

37、conducted on this item. a. First article inspection (See 4.3) b, Quality conformance inspection (see 4.4) 4.3 Fixst- article inspection, 4.3.1 Submission. The contractor shall submit. a first article sample as designated by the Contracting Officer for evaluation in accordance with provisions of 4.3.

38、2. The first- article sample shall consist of the assembljes, components and test specimens listed below in the quantities indicated, 4.3.2 Inspections to be performed. See MIL-A-48078 and Table I specified hereia, 4.3.3 Rejection. See MIL-A-48078 and the first article ballistic test shall be reject

39、ed if: a. b. c. d. e. f. h. Two or more misfires occur. Three or more duds occur without any misfires or if two or more duds occur with one misfire. . One or more short rounds occur, One or more premature bursts occur. One or more metal parts separation occur. Range and precision requirements are no

40、t met. (70 degrees F conditioned samples only). One or more dud plugs exit the projectile body in the inert fuze ballistic test. Two or more dud plugs fail to exit the projectile body in the live fuze ballistic tests (accumulatively, except in the case of a particular round that was an actual dud).

41、6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-711.50 9999906 1969113 701 = O -4 ci u a, a Lo c -ri a, d u .ri c: k cri *e U w IJ n n n n m m m m m L m mwww .e*. N*mmmm mmmmmm e. O O O O i 4 rl ri owoooo i0nnns-i u ciN I a, alpil 7 Provided

42、by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-71.150 (AR) 4.4 Quality Conformance Inspection 4.4.1 Inspection lot formation, Inspection lots shall comply with the lot. formation provisions of MIL-A-48078. In addition, inspection lots of practice cartr

43、idges shall contain: a. Projectile body metal parts assemblies of one inspection lot, from one manufacturer. b. M33 Fin assemblies of one inspection lot, from one manufacturer. c. Propelling charges made from not. more than one inspection lot of propellant., from one manufacturer. d. Obturating ring

44、s of one inspection lot, from one manufacturer. e, Fuzes of one inspection lot, from one manufacturer. f. Dud plugs from one inspection lot. that comply wi.th 3.3.7.2. 4.4.2 Examination and tests. a. Classification of characteristics. Quality conformance - examinations and tests are specified in the

45、 followi.ng Classification of Charact:eristics paragraphs. The contractors quality program or detailed inspection system shall provide assurance of compli-ance of all characteristi cis with the applicable drawing and specification requirements utilizing as a minimum the conformance criteria specifie

46、d. When cited herein, at-tributes sampling inspection shall be conducted in accordance wit,h Table i1 below, using the inspection levels stated in the C1assifj.cat.i.on of Characteristics paragraphs. 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-

47、MIL-C-7LL50 m 0b L9bLL5 584 LOT SIZE 2 to 8 9 to 15 16 to 25 26 to 50 51 to 90 91 to 150 151 to 280 281 to 500 501 to 1200 1201 to 3200 3201 to 10000 10001 to 35000 35001 to 350000 350001 to 500000 500000 and over I - * * * * * * * * * 1 250 1250 1250 1250 1250 1250 MIL-C-711.50 (AR) INSPECTION LEVE

48、LS - III IV - II - * * * * * * * 125 125 125 1 25 125 125 315 31 5 500 500 * 13 * 1.3 32 13 32 13 32 13 32 32 32 32 80 50 80 50 1 25 50 125 80 I25 80 200 125 200 1 25 m VI V 5 3 5 3 5 3 5 3 13 5 13 5 20 8 20 8 20 13 32 13 32 13 50 13 50 13 50 13 50 33 - - -. -.- Numbers under inspect.j.on levels ind

49、icate sample size; asterisks indicate one hundred percent inspection. If sample size exceeds lot size, perform one hundred percent inspection. Accept on zero and reject on one or more for all inspection levels. j. ._ - .- -. - - b. Alt.ernat.ive quality conformance provisions. Unless otherwise specified herein or provided for in the contract, alternative quality