ARMY A-A-56014-1989 HANDLE FOLDING MALE 65 DEG DETENT《65转男用可折叠制动器手柄》.pdf

《ARMY A-A-56014-1989 HANDLE FOLDING MALE 65 DEG DETENT《65转男用可折叠制动器手柄》.pdf》由会员分享，可在线阅读，更多相关《ARMY A-A-56014-1989 HANDLE FOLDING MALE 65 DEG DETENT《65转男用可折叠制动器手柄》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、A-A-560LLl 53 7777774 O002362 8 COMMERCIAL ITEM DESCRIPTION FOLDING, MALE 65 DETENT The Genera use of this HAHULE, 1 Services commerci a Abstract. This Commercial folding, male 90“ detent. Sal i ent characteri sti cs. Admi n A-A-56014 16 August S989 istratioil has authorized the 1 item description.

2、N- D IA Item Description covers one type of handle, 7 PIN r( SEE LOCKING ROLLPIN a BELOW) L HEX /INTERNAL TOOTH f FGURE 1 NUT . LOCKWASHER (2 .PLACES) . TABLE I. Dash Numbers D T NP MR HL E . DEGS. THREADS -1 .375 -375-24- .500 .625 .375 65 1.25 2.300 .625 5.000- + .005. 2A THD -2 - 3.000 (2 PLACES:

3、 ,l. 310 . -3 .312 2.375 I 4.500 + .O05 -4 - 6.440 1.750 I Beneficial comments, recommendations, additions, deletions, clarifications, etc., and data which may improve this documerlt should be sent to: Commander, U.S. Army Missile Command, ATTN: AMSMI-RD-SE-TD-ST, Redstone Arsenal, AL 35898-5270. DI

4、STRIBUTION STATEMENT A. Approved for public release.; distribution is unlimited. -., THIS DOCUMENT CONTAINS 3 PAGES. , 1c Licensed by Information Handling ServicesA-A-56014 Notes: 1, Handles shall be equipped with spring loaded detents with position grip as shown in figure 2, 2 . Materi al. Aluminum

5、 al loy per QQ-A-225/3, Type 2011 (Handle and Threaded Studs). 3. Protective finish. Black anodized per MIL-A-8625, Type II. 4, hardware, Handles shall be sopplied with unattached mounting hardware consisting of 2 nuts and 2 internal tooth lockwashers as follows: Lock vrashers shall be phosphor bron

6、ze, nickel plated per QQ-N-290, Class 1, Type I, Nuts shall be brass, chrome plated the same as the handle or finish with chemical black per MIL-F-495. 5. - Pin. Hal-dened Ground Proddction Dowel, .125 x .500 steel, per ANSI B18.8.2-1978, chromium plate per QQ-C-320 Class 1, Type II (Satin Finish) (

7、see figure 2 above). Contractor certification. The contractor shall certify and maintain substantiating evidence that the product offered meets the salient characteristics of this Cornrnercial Item Description, and that the product conforms to the producers own dratqings, specifications, standards,

8、and qual i ty assurance practices-. Tite Government reserves the right to require proof of such conformance prior to first delivery and thereafter as may be otherwise provided for under ,tile provisions of the contract Netric products. Products manufactured to metric dimensions will be considered on

9、 an equal basis with those manufactured using inch-pound units, provided they fall within specified tolerances using conversion tables contained in the latest revision of Federal Standard No. 375, and all other requirements of this Comaercial Item Ocscriptiotl are met. If a product is manufactured t

10、o metric dimensions and those dimensions exceed the tolerances specified in the inch/pound units, a request should be made to the contracting officer to determine if the product is acceptable. The contracting officer has tne option of accepting or rejecting the producx . Regulatory requirernants. Th

11、e offeror/contractor is encouraged to use recovered materials in accordance with Public Law 94-580 to the maximum extent practicable. Preservation, packaging, packing, labeling, and marking, Preservation, packaging, packing, labeling, and marking shall be as specified in the contract or order. 2 Lic

12、ensed by Information Handling ServicesA-A-56034 53 W 7777774 0002364 L A-A-56014 CID based part identification number. The fol numbesiny procedare is for Govwnmerit purpos2s and lowing part identifica.tion does not constitute a r2quirernmt for the co,rltractor. 3 Prupsii :)y Activity: 4r:;ny - MI FSC 5340 Licensed by Information Handling Services