ARMY A-A-52463 B-1996 LAMP BULBS INCANDESCENT MINIATURE SINGLE AND DOUBLE CONTACT BAYONET CANDELABRA BASE《刀片烛台型基座单和双接触的微型白炽灯灯泡》.pdf

《ARMY A-A-52463 B-1996 LAMP BULBS INCANDESCENT MINIATURE SINGLE AND DOUBLE CONTACT BAYONET CANDELABRA BASE《刀片烛台型基座单和双接触的微型白炽灯灯泡》.pdf》由会员分享，可在线阅读，更多相关《ARMY A-A-52463 B-1996 LAMP BULBS INCANDESCENT MINIATURE SINGLE AND DOUBLE CONTACT BAYONET CANDELABRA BASE《刀片烛台型基座单和双接触的微型白炽灯灯泡》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、INCH-POUNDA-A-52463BJune 28, 1996SUPERSEDINGA-A-52463ADecember 15, 1995COMMERCIAL ITEM DESCRIPTIONLAMP BULBS, INCANDESCENT, MINIATURE, SINGLE ANDDOUBLE CONTACT, BAYONET CANDELABRA BASEThe General Services Administration has authorized the use of this commercial item description (CID) for all federal

2、 agencies.1. SCOPE. This CID covers requirements for four types of miniature incandescent lamps used inmilitary ground vehicles.2. CLASSIFICATION. Miniature lamp bulbs shall be of the following types (see 7.3):Type I - Instrument light.Type II - Auto light.Type III - Stop, tail light.Type IV - Readi

3、ng light.3. SALIENT CHARACTERISTICS3.1 Materials. Materials shall be corrosion resistant or suitably treated to resist corrosion causedby fuel, salt spray, or atmospheric conditions as may be encountered in storage or normal service.The use of recovered material made in compliance with regulatory re

4、quirements is acceptableproviding that all requirements of this CID are met (see 4.1).3.1.1 Dissimilar metals. Dissimilar metals shall not be used in extremely close contact or havingdirect contact with each other unless protected against galvanic corrosion.3.2 Design and construction. The lamps sha

5、ll be designed as illustrated in figures 1 through 4.Unless otherwise specified herein, the lamp base shall be constructed in accordance with currentANSI C81.61.Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any otherdata which may improve this document should b

6、e sent by letter to: U.S. Army Tank-automotiveand Armaments Command, ATTN: AMSTA-TR-E/BLUE, Warren, MI 48397-5000.ASMC N/A FSC 6240DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.Provided by IHSNot for ResaleNo reproduction or networking permitted without license fro

7、m IHS-,-,-A-A-52463B2* see note 5.Average FormerType I Candle Design Filament life MS PartPIN Number Power Volts Amps Constr. (hours) NumbersAA52463-A01 3 + 20% 7.00 0.63 + 20% C-2R 1000 MS15570-63AA52463-A02 3 + 8% (2) 7.00 0.60 + 5% C-2R 1000 MS15570-63RAA52463-A03 6 + 20% 6.50 1.02 + 20% C-2R 500

8、 MS15570-81AA52463-A04 4 + 15% 13.50 0.59 + 8% C-2R (3) 2000 MS15570-67AA52463-A05 6 + 15% 13.00 0.58 + 8% C-2R 750 MS15570-89AA52463-A06 6 + 20% 28.00 0.30 + 10% C-2F 500 MS15570-303AA52463-A07 6 + 20% (2) 28.00 0.30 + 10% C-2F 500 MS15570-303RAA52463-A08 3 + 20% 28.00 0.23 + 10% 2C-2F 1000 MS15570

9、-1251AA52463-A09 6 + 20% 28.00 0.37 + 10% 2C-2F 1000 MS15570-623NOTES: 1. Bulbs for PIN numbers AA52463-A02 and AA52463-A07 are to be red.2. “Candle power” applies to the lamp before red coating is applied.3. Light center length is 0.81 inches.4. Dimensions are in inches (see 3.2) and are shown for

10、engineering reference purposes only. Do not scale.5. International interest: QSTAG 122, NATO STANAG 4008.FIGURE 1. BA15s Candelabra single-contact bayonet base, G6 bulb (type I).Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52463B3* see note 5.

11、Filament Average FormerType II Candle Design Construction life MS PartPIN Number Power Volts Amps (optional) (hours) NumbersAA52463-B01 21 7% 6.40 2.63 4% C-6 200 MS35478-1129AA52463-B02 15 9% 6.75 1.91 5% C-2R C-6 300 MS35478-87AA52463-B03 15 9% 12.80 1.04 5% C-2R C-6 500 MS35478-93AA52463-B04 21 1

12、0% 12.80 1.44 6% C-6 500 MS35478-1141AA52463-B05 15 15% 28.00 0.51 8% C-2V 300 MS35478-305AA52463-B06 21 15% 28.00 0.67 8% C-2V 300 MS35478-307AA52463-B07 21 15% (3) 28.00 0.67 8% C-2V 300 MS35478-307SBAA52463-B08 21 15% (3) 28.00 0.67 8% C-2V 300 MS35478-307RAA52463-B09 32 10% 28.00 0.90 8% C-2V 30

13、0 MS35478-315AA52463-B10 32 15% 28.00 1.02 8% 2C-2R 2C-6 500 MS35478-1683AA52463-B11 15 10% 28.00 0.61 8% 2C-2R 2C-2V 1000 MS35478-1691AA52463-B12 32 10% 6.00 4.10 8% C-6 300 MS35478-1680AA52463-B13 32 10% 12.80 1.80 5% C-6 200 MS35478-1073AA52463-B14 21 15% 28.00 0.80 8% C-2V 1000 MS35478-1665IFAA5

14、2463-B15 18 25% 28.00 .643 10% CC-8 2000 MS35478-2232AA52463-B16 21 25% 28.00 .766 10% CC-8 2000 MS35478-2233AA52463-B17 32 4 0.75 C-6 50 MS35478-BFTAA52463-B18 21 approx. 6.4 2.69 C-2V 200 MS35478-1605NOTES: 1. Bulb for PIN AA52463-B07 has a reflectorized coating which covers the top of the bulb to

15、 the filament center (see 3.3).2. Bulb for PIN AA52463-B08 is red.3. “Candle power” applies to the lamp before red or reflective coating is applied.4. Dimensions are in inches (see 3.2) and are shown for engineering reference purposes only. Do not scale.5. International interest: QSTAG 122, NATO STA

16、NAG 4008.FIGURE 2. BA15s Candelabra single-contact, bayonet base, S8 bulb (type II).Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52463B4Design Avrage FormerType III Trade Candle Power Amps Filament Life MS PartPIN Number No. Maj Fil. Min Fil.

17、Volts Maj Fil Min Fil Constr (hours) NumberAA52463-C01 1154 21 +8%3 +12%6.4/7.0 2.69 + 5% .75 + 8% 2C-6 200/2000 MS35481-1AA52463-C02 1016 21(2)6(2)12.8/14.0 1.26 (2) .57 (2) 2C-6 200/1000 MS35481-2NOTES: 1. Dimensions are in inches (see 3.2) and are shown for engineering reference purposes only. Do

18、 not scale.2. “Candle power” and “ampere” ratings are in accordance with manufacturers information.FIGURE 3. BAY15d Double-contact, bayonet base, S8 bulb (type III).Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52463B5* see note 3.Average Forme

19、rType IV Trade Design Filament life MS PartPIN Number Number Watts Volts Amps Construction (hours) NumbersAA52463-D01 1383 20 13 1.54 C-8 300 MS35480-1AA52463-D02 1385 20 28 0.714 CC-8 300 MS35480-2AA52463-D03 1384 20 6 3.33 C-8 300 MS35480-3NOTES: 1. Frosted area shall be acid etched or applied by

20、sand blasting exterior surface (see 3.3.1 for reflectorized area).2. Dimensions are in inches (see 3.2) and are shown for engineering reference purposes only. Do not scale.3. International interest: QSTAG 122, NATO STANAG 4008.FIGURE 4. BA15s Candelabra single-contact, bayonet base, R12 bulb (type I

21、V).3.3 Coating. The bulbs shall be clear unless otherwise indicated as being red color coated,reflectorized coated, or reflectorized coated-frosted (see figures). Coatings shall firmly adhereand be uniform without discoloring, cracking, fading or peeling.Provided by IHSNot for ResaleNo reproduction

22、or networking permitted without license from IHS-,-,-A-A-52463B63.3.1 Reflectorized coating. The reflectorized coating shall cover the area of the bulb indicatedin the applicable figures. The reflectorized coating shall be sensitized to receive a 0.005 inchcoating of pure silver followed by a protec

23、tive copper deposit, and then overlapping aluminum.As an optional procedure, the reflectorized coating may be aluminized by vacuum deposition.3.4 Environment. Lamps shall show no sign of deterioration when exposed to vibration, shock,temperature, or humidity while in use in vehicles.3.5 Rated averag

24、e laboratory life. The rated average laboratory life of the lamps shall be asspecified in figures 1 through 4. Where average life is specified, lamps shall give average life toburn-out of not less than what is specified.3.6 Identification and marking. Identification and marking shall be permanent an

25、d legible andshall include, as a minimum, the lamp industry trade number which correlates with the partnumber.4. REGULATORY REQUIREMENTS4.1 Recovered material. The offeror/contractor is encouraged to use recovered materials to themaximum extent practicable, in accordance with paragraph 23.403 of the

26、 Federal AcquisitionRegulation (FAR).5. QUALITY ASSURANCE PROVISIONS5.1 Responsibility for inspection. The contractor is responsible for the performance of allinspections (examinations and tests).5.2 Contractor certification. The contractor shall certify and maintain substantiating evidencethat the

27、product offered meets the salient characteristics of this CID and that the productconforms to the producers own drawings, specifications, workmanship standards, and qualityassurance practices. Items with known defects shall not be submitted for Governmentacceptance. The Government reserves the right

28、 to require proof of such conformance prior to thefirst delivery and thereafter as may be otherwise provided for under the provisions of the contract.6. PACKAGING. Preservation, packing, and marking shall be as specified in the contract ororder (see 7.3).Provided by IHSNot for ResaleNo reproduction

29、or networking permitted without license from IHS-,-,-A-A-52463B77. NOTES.(This section contains information of a general or explanatory nature that may be helpful, but isnot mandatory.)7.1 Part or identification number (PIN). The PINs to be used for lamps acquired to this CID arecreated as follows:A

30、A 52463 - X XXPart number (see figures 1 thru 4).Type: A - Instrument light (I).B - Auto light (II).C - Stop, tail light (III).D - Reading light (IV).CID number.Designates a CID.7.2 Addresses for obtaining copies of referenced documents.7.2.1 Government publications. The Code of Federal Regulations

31、(CFR) may be obtained fromthe Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402.7.2.2 Non-Government publications. Copies of industry specification ANSI C81.61 “ElectricalLamp Bases” are available from the American National Standards Institute (ANSI),1430 Broadway, N

32、ew York, NY 10018.7.3 Ordering data. Acquisition documents must specify the following:a. Title, number, and date of this CID.b. Issue of the DoDISS to be cited in the solicitation, and if required, the specified issue of individual documents referenced.c. Type, PIN, and quantity of lamps required.d.

33、 Selection of applicable level and packaging requirements.7.4 Cross-reference data. Lamps conforming to this CID are interchangeable/substitutable withlamps conforming to A-A-52463, MS15570F, MS35478K, MS35480, and MS35481.Provided by IHSNot for ResaleNo reproduction or networking permitted without

34、license from IHS-,-,-A-A-52463B87.5 Configuration. The configuration of the bulb is designated by the use of a letter (shape) and anumber (size) which expresses the approximate diameter in eighths of an inch.7.6 International interest. Certain provisions of this CID (figures 1, 2, and 4) are the sub

35、ject ofthe international standardization agreements (see figures for document reference). Whenamendment, revision, or cancellation of this CID is proposed that will modify the internationalagreement concerned, the preparing activity will take appropriate action through internationalstandardization c

36、hannels, including departmental standardization offices to change the agreementor make other appropriate accommodations. International interest is noted by use of an asterisk(*).MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY:GSA - FSSCustodians:Army - AT Preparing Activity:Navy - SH Army - ATAir Force - 99(Project 6240-1441)Review Activities:Army - AV, ER, MINavy - AS, YD1Air Force - 82DLA - GSProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-