ARMY A-A-52461-1993 STRAINER SEDIMENT AUTOMOTIVE FUEL (10 GPH)《10GPH汽车燃料沉积物过滤器》.pdf

《ARMY A-A-52461-1993 STRAINER SEDIMENT AUTOMOTIVE FUEL (10 GPH)《10GPH汽车燃料沉积物过滤器》.pdf》由会员分享，可在线阅读，更多相关《ARMY A-A-52461-1993 STRAINER SEDIMENT AUTOMOTIVE FUEL (10 GPH)《10GPH汽车燃料沉积物过滤器》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、A-A- 52 461 Auaust 12. 1993 SUPERSEDING MS51086H 10 December 1991 COMMERCIAL ITEM DESCRIPTION STRAINER, SEDIMENT: AUTOMOTIVE FUEL (10 GPH) The General Services Administration has authorized the use of this commercial item description (CID) as a replacement for MS51086H, which is canceled. This CID a

2、lso replaces the portions of canceled MIL-F-45356B which apply to MS51086H. ABSTRACT. This CID covers requirements for fuel filter strainers for use in the fuel system of internal combustion gasoline engines and accessories. a. Classification. Strainers shall be furnished in the following types (see

3、 note b). Type I - Strainer with shutoff valve. Type II - Strainer without shutoff valve. SALIENT CHARACTERISTICS. a. Materials. Unless otherwise specified herein. the materials used shall be in accordance with the manufacturers material specifications for strainers. The use of recovered materials m

4、ade in conformance with regulatory requirements is acceptable providing that all requirements of this CID are met (see note e). 1. Cover (head). The cover shall be made 3f a material which shall allow the strainer to perform to the requirements =f this CID. If made of steel, cover material shall be

5、zinc coated and the finished cover shall be treated with a corrosion inhibitor as per ASTM D2092, method B. 2. Bowl. The bowl material shall be brass, annealed, per ASTM B36 Unified Numbering System C24000, C26000, or C26800; zinc coated steel strip, carbon, cold rolled, per ASTM A109; or glass, ann

6、ealed, transparent. Steel bowls shall be treated with a corrosion inhibitor as per ASTM D2092, methoc! B. Beneficial comments, recommendations, additions, deletions clarifications, etc. and any other data which may improve this document should be sent by letter to: U.S. Army Tank-Automotive Command,

7、 ATTN: AMSTA-GDS, Warren, MI 48397-5000. AMSC N/A FSC 2910 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. a Licensed by Information Handling ServicesA-A- 5 2 46 1 3. Strainer element. The strainer element material shall be wire fabric, industrial per ASTM E437, tab

8、le II, 100 mesh, wire diameter (dia) .O045 inch (in.) or 120 mesh, wire dia .O037 in. Material: Steel, stainless, type 304 or 316; brass, high zinc content, copper-zinc alloy; or commercial bronze-copper, commercially pure. 4. Gasket. The filter bowl gasket material shall be in accordance with CID A

9、-A-52468-4. b. Desian and construction. 1. Envelope. The strainer shall be constructed to the form and dimensions as specified herein (see figure 1). The filter bowl shall be compatible with the bowl gasket. Design and construction that is not specified herein shall be in accordance with the best co

10、mmercial practices. 2. Bowl gasket. The filter bowl gasket shall be in accordance with CID A-A-52460-4. 3. Servicing. Servicing, including cleaning and reassembly, shall be easily accomplished without disturbing the strainers connection to the engine and shall be designed to prevent improper assembl

11、y. c. Performance. 1. Pressure-temperature resistance. The strainer shall show no signs of leakage or permanent deformation after being pressure tested at -65+ 3 degrees Fahrenheit (OF), 80 + 3OF, and 160 + 3F. The pressure used in thic test shall be 15 pounds per square inch (psi). -65OF and 80F te

12、sts. Air shall be used or the 160F test. For all tests the pressure shall be applied for 5 minutes and reduced to zero. - Test fluids shall be used for the 2. Flow rate. The nominal flow rate through the strainer shall be 10 gallons per hour (gph). The maximum differential pressure across the strain

13、er shall not exceed 4 psi. 3. Vibration resistance. The strainer shall show no evidence of cracking, deformation, loosening or leakage in the body at gaskets or at the fittings after exposure to a sinusoidal vibration for 3 hours along each axis. A frequency range of 5 to 500 cycles per second shall

14、 be used. The sweep time for the frequency range of 5 Hertz (Hz) to 500 Hz and return to 5 Hz shall be 15 minutes. * 4. Identification and markings. Identification and marking of strainers shall be permanent and legible and shall include as a minimum the manufacturers identification code (CAGE), and

15、 the part identification number (PIN) (see notes b and c) . QUALITY ASSURANCE PROVISIONS a. Responsibility for inspection. The contractor is responsible for the performance of all inspections (examinations and tests). b. Contractor certification. The contractor shall certify and maintain substantiat

16、ing evidence that the product offered meets the salient characteristics of this commercial item description and the the product conforms to the producers own drawings, specifications, workmanship standards, and quality assurance practices. Items with known defects shall not be submitted for 2 Licens

17、ed by Information Handling ServicesA-A-524bL = 9999974 0155335 T9b CROSS REFERENCE (CID Part Former MS /Former Army Type1 number part number part number l I (A52461-1 MS51086-1 7089773 1 II /A52461-2 HS51086-2 NONE A-A-52 461 PPPROX HARKING 1/8-27 ORYSUL NPTF (VALVE OPEN) Type1 FINGER SHIPP1 NC SHUT

18、 OFF /VALVE - -BOWL GASKfT (SEE FIGURE 21 + 2.25 .031- 1/8-27 DRYSEAI. NPTF 2 PLACES 7 5 NOTES: 1. Dimensions are Ln inches 2. MRK = Maximum. 3. APPROX = Approxmate. FIGURE 1. Strainer, sediment: automotive fuel (10 GPH). 3 Licensed by Information Handling ServicesA-A-524bL 9999974 015533b 922 A-A-5

19、2 46 1 Government acceptance. The Government reserves the right to require proof of such conformance prior to the first delivery and thereafter as may be otherwise provided for under the provisions of the contract. PRESERVATION, PACKAGING, PACKING, LABELING, AND MARKING. Preservation, packaging, pac

20、king, labeling, and marking for the desired level shall be as specified in the contract (see note b). NOTES. (This section contains information of a general or explanatory nature that may be helpful, but is not mandatory.) a. Addresses for obtaining copies of non-Government publications. ASTM A109 “

21、Standard Specifications for Steel Strip, Carbon, Cold Rolled“; ASTM B36 “Standard Specifications for Brass Plate, Sheet, Strip and Rolled Bar“; ASTM E437 “Standard Specifications for Industrial Wire Cloth and Screens“, ASTM D2092 “Standard Practice for Preparation of Zinc-Coated Steel Surfaces for P

22、aint“, are available from the American Society for Testing and Materials (ASTM), 1916 Race Street, Philadelphia, PA 19103. b. Ordering data. Acquisition documents must specify the following: 1. 2. 3. 4. 5. Title, number, and date of this CID. Issue of the DODISS to be cited in the solicitation, and

23、if required, the specific issue of individual documents referenced. Type of strainer. Part identification number (PIN). Selection of applicable level and packaging requirements. c. Part or identification number (PIN). The PINS to be used for the strainers acquired to this CID are created as follows:

24、 A 52461 - X Type of strainer 1 - Type I (with shutoff valve) 2 - Type II (without shutoff valve) IT CID number. I CID designator. d. Cross-reference data. Strainers conforming to this CID are interchangeable/substitutable with strainers conforming to MS51086H and MIL-F-45356BI dated 10 December 199

25、1 and 25 July 1984 respectively. e. Regulatory requirements. The offeror/contractor is encouraged to use recovered materials in accordance with Public Law 94-580 to the maximum extent practicable. 4 Licensed by Information Handling ServicesMILITARY INTERESTS: a Custodians A-A-52461 m 9999974 0155337 869 D A-A-5246 1 Army - AT Air Force - 99 Review Activities Army - ME DLA - CS User Activity Air Force - 82 Navy - MC CIVIL AGENCY COORDINATING ACTIVITY: GSA - FSS PREPARING ACTIVITY: Army - AT (Project 2910-0226) Licensed by Information Handling Services