ANSI UL 1332-2005 UL Standard for Safety Organic Coatings for Steel Enclosures for Outdoor Use Electrical Equipment (Fourth Edition Reprint with Revisions Through and Including Jun.pdf

《ANSI UL 1332-2005 UL Standard for Safety Organic Coatings for Steel Enclosures for Outdoor Use Electrical Equipment (Fourth Edition Reprint with Revisions Through and Including Jun.pdf》由会员分享，可在线阅读，更多相关《ANSI UL 1332-2005 UL Standard for Safety Organic Coatings for Steel Enclosures for Outdoor Use Electrical Equipment (Fourth Edition Reprint with Revisions Through and Including Jun.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULUL 1332Organic Coatings for SteelEnclosures for Outdoor UseElectrical EquipmentUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULUL COPYRIGH

2、TED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULUL Standard for Safety for Organic Coatings for Steel Enclosures for Outdoor Use Electrical Equipment,UL 1332Fourth Edition, Dated February 9, 2005Summary of TopicsRevision pages are being issued to reflect

3、 the recent reaffirmation of UL 1332 as an AmericanNational Standard.Text that has been changed in any manner or impacted by ULs electronic publishing system is markedwith a vertical line in the margin. Changes in requirements are marked with a vertical line in the marginand are followed by an effec

4、tive date note indicating the date of publication or the date on which thechanged requirement becomes effective.All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, ortransmitted in any form by any means, electronic, mechanical photocopying, recording, or

5、 otherwisewithout prior permission of UL.UL provides this Standard as is without warranty of any kind, either expressed or implied, including butnot limited to, the implied warranties of merchantability or fitness for any purpose.In no event will UL be liable for any special, incidental, consequenti

6、al, indirect or similar damages,including loss of profits, lost savings, loss of data, or any other damages arising out of the use of or theinability to use this Standard, even if UL or an authorized UL representative has been advised of thepossibility of such damage. In no event shall ULs liability

7、 for any damage ever exceed the price paid forthis Standard, regardless of the form of the claim.Users of the electronic versions of ULs Standards for Safety agree to defend, indemnify, and hold ULharmless from and against any loss, expense, liability, damage, claim, or judgment (including reasonabl

8、eattorneys fees) resulting from any error or deviation introduced while purchaser is storing an electronicStandard on the purchasers computer system.The requirements in this Standard are now in effect, except for those paragraphs, sections, tables, figures,and/or other elements of the Standard havin

9、g future effective dates as indicated in the note following theaffected item. The prior text for requirements that have been revised and that have a future effective dateare located after the Standard, and are preceded by a SUPERSEDED REQUIREMENTS notice.JUNE 3, 2010 UL 1332 tr1UL COPYRIGHTED MATERI

10、AL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULJUNE 3, 2010 UL 1332tr2No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULFEBRUARY 9, 2005(Title Page Reprinted: June 3, 2010)1UL 1332Standard

11、 for Organic Coatings for Steel Enclosures for Outdoor UseElectrical EquipmentFirst Edition March, 1986Second Edition June, 1990Third Edition February, 1995Fourth EditionFebruary 9, 2005This ANSI/UL Standard for Safety consists of the Fourth Edition, includingrevisions through June 3, 2010.The most

12、recent designation of ANSI/UL 1332 as a Reaffirmed American NationalStandard (ANS) occurred on June 3, 2010. ANSI approval for a standard doesnot include the Cover Page, Transmittal Pages, Title Page, or effective dateinformation. Any other portions of this ANSI/UL standard that were not processedin

13、 accordance with ANSI/UL requirements are noted at the beginning of theimpacted sections.Comments or proposals for revisions on any part of the Standard may besubmitted to UL at any time. Proposals should be submitted via a ProposalRequest in ULs On-Line Collaborative Standards Development System (C

14、SDS)at http:/.ULs Standards for Safety are copyrighted by UL. Neither a printed nor electroniccopy of a Standard should be altered in any way. All of ULs Standards and allcopyrights, ownerships, and rights regarding those Standards shall remain thesole and exclusive property of UL.COPYRIGHT 2010 UND

15、ERWRITERS LABORATORIES INC.ANSI/UL 1332-2005 (R2010)UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULJUNE 3, 2010UL 13322No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM

16、ULCONTENTSINTRODUCTION1 Scope .42 Glossary .43 Units of Measurement .54 Undated References 5PERFORMANCE5 Specimens for Test .56 Specimen Preparation .57 Salt-Spray (Fog) Test 68 Moist Carbon Dioxide-Sulfur Dioxide-Air Test .69 Light and Water Test for Clear Coatings .7MARKING10 General .8APPENDIX A

17、ORGANIC COATING IDENTIFICATIONA1 Scope .A1A2 General .A1A3 Test for Weight Per Gallon of Liquid Coating A1A3.1 General .A1A3.2 Test procedure A2A4 Test for Percent Solids A2A4.1 General .A2A4.2 Test procedure .A2AA5 Test for Percent Pigment A3A5.1 General .A3A5.2 Test procedure A3A6 Test for Percent

18、 Ash A3A7 Infrared-Analysis Test .A4JUNE 3, 2010 UL 1332 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULINTRODUCTION1 Scope1.1 These requirements cover tests of opaque and clear organic coatings intended for application toexterior and interi

19、or surfaces of steel enclosures of outdoor-use electrical equipment for protection of themetal against atmospheric corrosion.1.2 These requirements cover organic coatings consisting of one or more coats and their system ofapplication to steel or zinc-coated steel with specified pretreatment, applica

20、tion, bake or cure schedule,and minimum dry-film thickness.1.3 The final acceptance of a coating is dependent upon its use in a complete product that complies withthe requirements in the standard applicable to such a product.1.4 The requirements may be applied to other organic or nonmetallic coating

21、s if found to be appropriate.1.5 The flammability or toxicity risks associated with the coating materials in any form, or the acceptabilityof the materials for uses other than indicated, are not within the scope of these requirements.1.6 A product that contains features, characteristics, components,

22、 materials, or systems new or differentfrom those covered by the requirements in this standard, and that involves a risk of fire, electric shock, orinjury to persons shall be evaluated using the appropriate additional component and end-productrequirements as determined necessary to maintain the acce

23、ptable level of safety as originally anticipatedby the intent of this standard. A product whose features, characteristics, components, materials, orsystems conflict with specific requirements or provisions of this standard cannot be judged to comply withthis standard. Where considered appropriate, r

24、evision of requirements shall be proposed and adopted inconformance with the methods employed for development, revision, and implementation of this standard.2 Glossary2.1 For the purpose of this standard, the following definitions apply.2.2 APPLICATION METHOD The procedure and equipment employed in

25、applying the coating, whichmay also include parameters of equipment operation.2.3 BAKE OR CURE SCHEDULE The time-temperature conditions used following the application ofan organic coating.2.4 ORGANIC COATING A coating containing drying oils, resins, and setting or hardening agentssuch as reacting ch

26、emicals and catalysts or resins.2.5 PRETREATMENT The cleaning or chemical process, such as iron or zinc phosphating, used onthe metal surface prior to application of the organic coating.2.6 SUBSTRATE The specific metal surface to which the organic coating is to be applied.FEBRUARY 9, 2005UL 13324UL

27、COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM UL3 Units of Measurement3.1 If a value for measurement is followed by a value in other units in parentheses, the second value maybe only approximate. The first stated value is the requirement.4 Undate

28、d References4.1 Any undated reference to a code or standard appearing in the requirements of this standard shall beinterpreted as referring to the latest edition of that code or standard.PERFORMANCE5 Specimens for Test5.1 Specimens representative of the coating system are to be employed in these tes

29、ts. The sheet steelused in the preparation of specimens of the coating is to be representative of the steel for which thecoating is intended, with respect to composition and surface conditions. The specimens are to beprepared by the same procedures of surface cleaning, pretreatment, application of t

30、he coating system,drying or curing, and minimum dry-film thickness that will be used in the end-use product.5.2 If a coating system is intended to be used in a range of colors, specimens representing the range areto be tested. Specimens with the highest pigment to vehicle or resin ratio, lowest pigm

31、ent to vehicle orresin ratio, and metallic pigment are to be tested. If specific color pigments are known to have unusual orcritical properties, they are also to be tested.5.3 Test specimens are to be 4 inches (102 mm) wide and 12 inches (305 mm) long, with the thicknessof the base metal being repre

32、sentative of that in the end-use application.6 Specimen Preparation6.1 The edges or bare surfaces of all specimens are to be covered with moisture-resistant tape orcompound. Two of the specimens are to be scribed in accordance with the Method for Evaluation ofPainted or Coated Specimens Subjected to

33、 Corrosive Environments, ASTM D1654-92. A single 8 inch(203.2 mm) diagonal V-cut scribe running lengthwise across the specimen is to be used. The scribe is tobe free of burrs and is not to contact the edges. The scribing tool used is to be either:a) A carbide tipped tool Style E, with 1/64-inch (0.4

34、-mm) nose radius, orb) A carbide tipped tool ground to a single point having an included angle of 60 15 degrees.FEBRUARY 9, 2005 UL 1332 5UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM UL7 Salt-Spray (Fog) Test7.1 Two scribed and two unscribed

35、specimens shall be exposed for 600 hours to salt spray in accordancewith 7.2. Following exposure, specimens shall:a) Not show more than light corrosion beneath the coating with no visual pitting of substrateand only incipient buildup or weeping of corrosion, not including the scribe,b) Comply with T

36、able 7.1, andc) Not exhibit an average creepage distance from the scribe greater than Rating No. 5 1/8 to3/16 inch (3.1 4.7 mm) as designated in the Standard Evaluation of Painted or CoatedSpecimens Subjected to Corrosive Environments, ASTM D1654, Procedure A, Method 2; withmaximum isolated spot not

37、 exceeding 3/8 inch (9.5 mm).Table 7.1Blister size and frequencyMaximum sizeaMaximum frequency2or4 Few6 or 8 MediumNote Compliance is to be determined in accordance with the Standard Method of Evaluating Degree of Blistering of Paints,ASTM D714-87.aThe largest blister size is Number 2 and the smalle

38、st blister size is Number 8.7.2 The specimens are to be exposed to salt spray in accordance with the Standard Method of Salt-Spray(Fog) Testing, ANSI/ASTM B117-94.8 Moist Carbon Dioxide-Sulfur Dioxide-Air Test8.1 Two scribed and two unscribed specimens shall be exposed for 1200 hours to a mixture of

39、 moistcarbon dioxide and sulfur dioxide and air as described in 8.2 8.4. Following exposure, specimens shall:a) Except for the scribe, not show more than light corrosion beneath the coating with no visualpitting of substrate and only incipient buildup or weeping of corrosion products,b) Comply with

40、Table 8.1, andc) Not exhibit an average creepage distance from the scribe greater than Rating No. 6 1/16 to1/8 inch (1.6 3.2 mm) as designated in the Standard Evaluation of Painted or CoatedSpecimens Subjected to Corrosive Environments, ASTM D1654-92, Procedure A, Method 2;with maximum isolated spot

41、 not exceeding 3/8 inch (9.5 mm).FEBRUARY 9, 2005UL 13326UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULTable 8.1Blister size and frequencyMaximum sizeaMaximum frequency2 None4 or 6 Medium8 Medium denseNote Compliance is to be determined in a

42、ccordance with the Standard Method of Evaluating Degree of Blistering of Paints,ASTM D714-87.aThe largest blister size is Number 2 and the smallest blister size is Number 8.8.2 The apparatus used for the moist carbon dioxide-sulfur dioxide-air exposure is to consist of achamber having a volume of at

43、 least 3 cubic feet (0.08 m3) with a water jacket and thermostaticallycontrolled heater to maintain a temperature of 95 plus 2 or minus 3F (35 plus 1.1 or minus 1.7C).8.3 Sulfur dioxide and carbon dioxide are to be supplied to the test chamber from commercial cylinderscontaining the gases under pres

44、sure. An amount of sulfur dioxide equivalent to 1 percent of volume of thetest chamber, and an equal volume of carbon dioxide are to be introduced into the chamber each workingday. Prior to introducing the new charge of gas each day, the remaining gas-air mixture from the previousday is to be purged

45、 from the chamber. A small amount of water (approximately 10 ml/0.0003 m3ofchamber volume) is to be maintained at the bottom of the chamber for humidity. This water is not to bechanged during the exposure.8.4 The specimens are to be supported in plastic racks at an angle of 15 to 30 degrees from the

46、 vertical.9 Light and Water Test for Clear Coatings9.1 Two scribed and two unscribed specimens shall be exposed for 360 hours to light and water inaccordance with 9.2. Following exposure, specimens shall:a) Except for the scribe, show no base metal corrosion,b) Show no blisters,c) Not exhibit an ave

47、rage creepage distance from the scribe greater than rating No. 6 1/16 to1/8 inch (1.6 3.2 mm) as designated in the Standard Evaluation of Painted or CoatedSpecimens Subjected to Corrosive Environments, ASTM D1654-92, Procedure A, Method 2;with maximum isolated spot not exceeding 3/8 inch (9.5 mm), a

48、ndd) Not show more than light corrosion of the base metal beneath coating uplifted from thescribe with no visual pitting of substrate and only incipient buildup of corrosion products.9.2 The specimens are to be exposed to light and water in accordance with Method I of the StandardPractice for Operat

49、ing Light- and Water-Exposure Apparatus (Carbon-Arc Type) With and Without Waterfor Exposure of Nonmetallic Materials, ASTM G23-93, using apparatus designated Type DH in ASTMG23-93. During each operating cycle of 120 minutes, each specimen is to be exposed to:a) Light for 102 minutes, andb) Water spray with light for 18 minutes.FEBRUARY 9, 2005 UL 1332 7UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULMARKING10 General10.1 A product container shall be marke