ANSI ASTM F2093-2011 Standard Test Method for Performance of Rack Ovens《搁架式烤炉的性能试验方法》.pdf

《ANSI ASTM F2093-2011 Standard Test Method for Performance of Rack Ovens《搁架式烤炉的性能试验方法》.pdf》由会员分享，可在线阅读，更多相关《ANSI ASTM F2093-2011 Standard Test Method for Performance of Rack Ovens《搁架式烤炉的性能试验方法》.pdf（19页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F2093 11 An American National StandardStandard Test Method forPerformance of Rack Ovens1This standard is issued under the fixed designation F2093; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revisi

2、on. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method evaluates the energy consumption andbaking performance of rack ovens. The food service operatorcan use this eval

3、uation to select a rack oven and understand itsenergy performance.1.2 This test method is applicable to thermostaticallycontrolled, gas and electric rack ovens.1.3 The rack oven can be evaluated with respect to thefollowing (where applicable):1.3.1 Energy input rate (10.2),1.3.2 Thermostat calibrati

4、on (10.3),1.3.3 Preheat energy and time (10.4),1.3.4 Idle energy rate (10.5),1.3.5 Pilot energy rate, if applicable (10.6),1.3.6 White sheet cake browning (10.7), and1.3.7 Steam performance (10.8), and1.3.8 Baking energy efficiency and production capacity(10.9).1.4 The values stated in inch-pound un

5、its are to be regardedas standard.1.5 This test method may involve hazardous materials,operations, and equipment. This standard does not purport toaddress all of the safety concerns, if any, associated with itsuse. It is the responsibility of the user of this standard toestablish appropriate safety

6、and health practices and deter-mine the applicability of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D3588 Practice for Calculating Heat Value, CompressibilityFactor, and Relative Density of Gaseous FuelsF1496 Test Method for Performance of Convection Ovens2.2 ANSI

7、 Document:3ANSI Z83.11 American National Standard for Gas FoodService Equipment2.3 ASHRAE Documents:4ASHRAE Fundamentals 1997ASHRAE Guideline 2-1986 (RA90) Engineering Analysisof Experimental Data3. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 bake time, ntime required to bake

8、 the frozen piesspecified in 7.3.3.1.2 baking cavity, nthat portion of the appliance inwhich food products are heated or cooked.3.1.3 baking energy, nenergy consumed by the rack ovenas it is used to bake frozen pies under full-load conditions.3.1.4 baking energy effciency, nquantity of energy im-par

9、ted to the pies, expressed as a percentage of energyconsumed by the rack oven during the baking event.3.1.5 baking energy rate, naverage rate of energy con-sumption (Btu/h or kW) during the baking energy efficiencytests.3.1.6 duty cycle, ndefined as percent (%) of burner timeon divided by a complete

10、 on/off cycle during idle energy modeat 400F.3.1.7 idle energy rate, nthe rate of energy consumed(Btu/h or kW) by the rack oven while “holding” or “idling” thebaking cavity at the thermostat set point.3.1.8 measured energy input rate, npeak rate at which arack oven consumes energy (Btu/h or kW), typ

11、ically reflectedduring preheat.3.1.9 mini-rack oven, nan appliance that bakes by forcingair within a closed cavity, either fitted with a mechanism forrotating an internal rack which accomodates 8 pans at 4 in.spacing or a fixed 8 pans at 4 in. spacing within the cavity.1This test method is under the

12、 jurisdiction of ASTM Committee F26 on FoodService Equipment and is the direct responsibility of Subcommittee F26.06 onProductivity and Energy Protocol.Current edition approved June 1, 2011. Published July 2011. Originally approvedin 2001. Last previous edition approved in 2006 as F2093 06. DOI: 10.

13、1520/F2093-11.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from American National Standards Ins

14、titute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036, http:/www.ansi.org.4Available from American Society of Heating, Refrigerating, and Air-Conditioning Engineers, Inc. (ASHRAE), 1791 Tullie Circle, NE, Atlanta, GA30329, http:/www.ashrae.org.Copyright ASTM International, 100 Barr Harbor Driv

15、e, PO Box C700, West Conshohocken, PA 19428-2959. United States13.1.10 nameplate energy input rate, nthe maximum orpeak rate at which an appliance consumes energy as rated bythe manufacturer and specified on the nameplate.3.1.11 pilot energy rate, naverage rate of energy con-sumption (Btu/h) by a ra

16、ck ovens continuous pilot (if appli-cable).3.1.12 preheat energy, namount of energy consumed bythe rack oven while preheating the baking cavity from ambientroom temperature (75 6 5F) to the thermostat set point.3.1.13 preheat rate, naverage rate (F/min) at which therack ovens baking cavity is heated

17、 from ambient temperature(75 6 5F) to the thermostat set point: defined as the settemperature minus ambient temperature divided by the preheattime.3.1.14 preheat time, ntime required for the rack oven topreheat from ambient room temperature (75 6 5F) to thethermostat set point.3.1.15 production capa

18、city, nmaximum rate (lb/h) atwhich the rack oven can bake frozen pies as specified in 7.3.3.1.16 rack, na device which is used to hold pans withina rack oven.3.1.17 rack oven, nan appliance that bakes by forcing hotair over the food within a closed cavity, either fitted with amechanism for rotating

19、one or more racks, or one or morenon-rotating racks within the cavity.3.1.18 steam injection cycle, na period whereby steam isintroduced into the baking cavity during baking.3.1.19 uncertainty, nmeasure of systematic and precisionerrors in specified instrumentation or measure of repeatabilityof a re

20、ported test result.4. Summary of Test Method4.1 The rack oven is connected to the appropriate meteredenergy source, and energy input rate is determined to confirmthat the appliance is operating within 5 % of the nameplateenergy input rate.4.2 The accuracy of the ovens thermostat is checked at400F an

21、d adjusted as necessary.4.3 The amount of energy and time required to preheat therack oven to 400F is determined.4.4 The idle energy rate is determined with the rack oven setto maintain 400F in the baking cavity.4.5 Pilot energy rate is determined, when applicable, for gasrack ovens.4.6 The rack ove

22、n is used to bake a full-load of white sheetcakes (8 cakes in a mini-rack, 15 cakes in a single-rack oven,and 30 cakes in a double-rack oven, for example) to assess thebrowning uniformity of the oven.4.7 The rack ovens steam performance is characterized byassessing the amount of steam produced on re

23、peated bakecycles.4.8 The rack oven is used to bake a full-load of frozen pies.Baking energy efficiency, baking energy rate, and productionrate are determined from these tests.5. Significance and Use5.1 The energy input rate and thermostat calibration testsare used to confirm that the rack oven is o

24、perating properlyprior to further testing.5.2 Preheat energy and time can be useful to food serviceoperators to manage energy demands and to know how quicklythe rack oven can be ready for operation.5.3 Idle energy rate and pilot energy rate can be used by thefood service operator to estimate energy

25、consumption duringnon-baking periods.5.4 The ovens browning and baking uniformity can be usedby an operator to select an oven that bakes a variety of productsevenly.5.5 Steam performance can be useful for a food serviceoperator interested in the ovens ability to consistently createsteam during a bak

26、ing cycle.5.6 Baking energy efficiency is a precise indicator of rackoven energy performance under various loading conditions.This information enables the food service operator to considerenergy performance when selecting a rack oven.5.7 Production capacity is used by food service operators tochoose

27、 a rack oven that matches their food output require-ments.6. Apparatus6.1 Analytical Balance Scale, for measuring weights up to25 lb, with a resolution of 0.01 lb and an uncertainty of 0.01 lb.6.2 Barometer, for measuring absolute atmosphericpressure, to be used for adjustment of measured gas volume

28、 tostandard conditions. Shall have a resolution of 0.2 in. Hg andan uncertainty of 0.2 in. Hg.6.3 Data Acquisition System, for measuring energy andtemperatures, capable of multiple channel displays updating atleast every 2 s.6.4 Freezer, sized large enough to hold a full-load of frozenpies (24 pies

29、for a mini-rack oven, 45 pies for a single rackoven, and 90 pies for a double rack oven) and capable ofmaintaining the frozen product at 0 6 5F.6.5 Flow Meter, for measuring total water consumption ofthe oven, having a resolution of 0.01 gal and an uncertainty of0.01 gal for flows of 0.2 gpm and hig

30、her.6.6 Gas Meter, for measuring the gas consumption of a rackoven, shall be a positive displacement type with a resolution ofat least 0.01 ft3and a maximum uncertainty no greater than1 % of the measured value for any demand greater than 2.2ft3/h. If the meter is used for measuring the gas consumed

31、bythe pilot lights, it shall have a resolution of at least 0.01 ft3anda maximum uncertainty no greater than 2 % of the measuredvalue.6.7 Heavy-Duty Chefs Thermometers, capable of with-standing 400F temperatures for monitoring food temperaturewhile baking. A 2-in. or larger dial is recommended forenh

32、anced visibility.F2093 1126.8 Platform Balance Scale, or appropriate load cells, formeasuring weights up to 500 lb with a resolution of 0.2 lb andan uncertainty of 0.2 lb.6.9 Pressure Gauge, for monitoring gas pressure. Shall havea range of zero to 15 in. H2O, a resolution of 0.5 in. H2O, anda maxim

33、um uncertainty of 1 % of the measured value.6.10 Stop Watch, with a 1-s resolution.6.11 Temperature Sensor, for measuring gas temperature inthe range of 50 to 100F with an uncertainty of 61F.6.12 Thermocouple(s), industry standard type K thermo-couple wire with a range of 0 to 600F and an uncertaint

34、y of61F.6.13 Thermocouple Probe, “fast response” type T or type Kthermocouple probe,116 in. or smaller diameter, witha3sorfaster response time, capable of immersion with a range of 30to 300F and an uncertainty of 61F. The thermocoupleprobes active zone shall be at the tip of the probe.6.14 Watt-Hour

35、 Meter, for measuring the electrical energyconsumption of a rack oven, shall have a resolution of at least10Wh and a maximum uncertainty no greater than 1.5 % of themeasured value for any demand greater than 100 W. For anydemand less than 100 W, the meter shall have a resolution of atleast 10 Wh and

36、 a maximum uncertainty no greater than 10 %.7. Reagents and Materials7.1 Aluminum Sheet Pans, measuring 18 by 26 by 1 in. forthe baking energy efficiency and sheet cake browning tests.7.2 Cake Mix, generic white cake mix, 5 lb per box. Aminimum of 30 lb is required for mini-rack ovens, 50 lb forsing

37、le-rack ovens, and 100 lb for double-rack ovens.7.3 Frozen Pies, 10-in. frozen, commercial-grade, ready-to-bake apple pies, weighing 3.00 6 0.15 lb, with a moisturecontent of 54 6 2 %, by weight for baking energy efficiencyand production capacity tests. The pie crust shall be made with100 % vegetabl

38、e shortening and the filling shall be a pre-cooked apple based filling (see Fig. 1).NOTE 1Sysco Classic fruit pies have been shown to be an acceptableproduct for testing by Pacific Gas and Electric Company.7.4 Hotel Pan, to be used to collect water runoff duringtesting.7.5 Paper Baking Liners, to li

39、ne sheet pans for browninguniformity tests.7.6 Plastic Wrap, commercial grade, 18-in. wide.7.7 Rack, supplied by the oven manufacturer shall have anominal 4-in. spacing between pan positions, with a minimumof 4-in. between the top pan and the top of the top of the rackand a minimum of 4-in. between

40、the bottom pan and the floor.7.8 Water, supplied to the rack oven shall be 65 6 5F. Ifoutside this range, hot and cold water supplies may be mixedto achieve the required inlet temperature.8. Sampling, Test Units8.1 Rack OvenSelect a representative production modelfor performance testing.9. Preparati

41、on of Apparatus9.1 Install the oven according to the manufacturers instruc-tions in an appropriate space. All sides of the oven shall be aminimum of 6-in. from any side wall, side partition, or otheroperating appliance. The oven, moisture vent, and hoodassembly, as furnished, shall be vented to the

42、exterior of thetesting space, using the manufacturers specified ventilationrate(s). The associated heating or cooling system for the spaceshall be capable of maintaining an ambient temperature of 756 5F within the testing environment (outside the vertical areaof the rack oven) when the combined oven

43、 exhaust ventilationsystem is operating.9.2 Install a thermocouple at the vertical center of theovens pressure panel in the air outlet, with the sensing tip 1.06 0.25-in. away from the vertical plane of the panel to recordthe oven cavity temperature. Make certain that the thermo-couple sensing tip i

44、s not touching the pressure panel or any ofits components.9.3 Adjust the air baffles inside the oven cavity to themanufacturers recommended gap settings. Follow the manu-facturers recommendation for fine adjustments.9.4 Connect the rack oven to a calibrated energy test meter.For gas installations, i

45、nstall a pressure regulator downstreamfrom the meter to maintain a constant pressure of gas for alltests. Install instrumentation to record both the pressure andtemperature of the gas supplied to the rack oven and thebarometric pressure during each test so that the measured gasflow can be corrected

46、to standard conditions. For electricinstallations, a voltage regulator may be required during tests ifthe voltage supply is not within 62 .5 % of the manufacturersnameplate voltage.9.5 For a gas rack oven, adjust (during maximum energyinput) the gas supply pressure downstream from the appli-ances pr

47、essure regulator to within 62.5 % of the operatingFIG. 1 Cross Section of a Frozen Apple PieF2093 113manifold pressure specified by the manufacturer. Make adjust-ments to the appliance following the manufacturers recom-mendations for optimizing combustion. Proper combustionshall be verified by measu

48、ring air-free CO in accordance withANSI Z83.11.9.6 For an electric rack oven, confirm (while the elementsare energized) that the supply voltage is within 62.5 % of theoperating voltage specified by the manufacturer. Record thetest voltage for each test.NOTE 2It is the intent of the testing procedure

49、 herein to evaluate theperformance of a rack oven at its rated gas pressure or electric voltage. Ifan electric unit is rated dual voltage (this is, designed to operate at either240 or 480 V with no change in components), the voltage selected by themanufacturer and/or tester shall be reported. If a rack oven is designed tooperate at two voltages without a change in the resistance of the heatingelements, the performance of the unit (for example, preheat time) maydiffer at the two voltages.9.7 Install a flow meter to the rac