AIR FORCE MIL-I-38357 A (3)-1979 INDICATOR BEARING-DISTANCE-HEADING ID-1103A ARN《ID-1103A ARN型方位、距离、船首向指示器》.pdf

《AIR FORCE MIL-I-38357 A (3)-1979 INDICATOR BEARING-DISTANCE-HEADING ID-1103A ARN《ID-1103A ARN型方位、距离、船首向指示器》.pdf》由会员分享，可在线阅读，更多相关《AIR FORCE MIL-I-38357 A (3)-1979 INDICATOR BEARING-DISTANCE-HEADING ID-1103A ARN《ID-1103A ARN型方位、距离、船首向指示器》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、MILITARY SPECIFICATION INDICATOR, BEARING-DISTANCE-HEADING ID-l103/ARN This amendment forms a part of Military Specification MIL-I-38357A (USAF) dated 21 December 1971. PAGE 1 Tit 1 e : Dele te I ID- 11 O 3/ARN“ and subs ti tute ID- 11 O 3A/ARN“, Paragraph 1.1, line 2: Delete “ID-l103/ARN“ and subst

2、itute “ID- 1103A/ARN“. PAGE 3 3; 3.3: Delete and substitute “Materials. “Recycled and recovered raw materials should be used to maximum extent possible in lieu of virgin raw materials as long as these materials do not jeopardize the intended use and fully comply with all contract requirements. Mater

3、ials used shall be free from defects which would adversely affect the performance or maintainability of individual components or the overall assembly. Materials not specified herein shall be of the same quality used for the intended purpose in commercial practice. None of the above shall be interpre

4、ted to mean that the use of used or rebuilt products will be allowed“. I PAGE 4 * 3.4.3, first sentence: Delete and substitute: “Unless otherwise approved by the procuring activity (see 6.2.1), the outline dimensions of the case shall conform to MS27572 for the 3-inch size, dimension L shall not exc

5、eed 7.5 inches, and dimension G shall be 0.470 to 0.545 inch“. PAGE 7 3.4.5, first and second sentences: Delete and substitute: “Unless otherwise approved by the procuring activity (see 6.2.2) , the dial shall be in accordance with figure 1 and all visible portions of the dial shall be lusterless bl

6、ack, color No. 37038 of FED-STD- 595“. PAGE 8 Figure 1: -Delete and substitute the attached figure 1. Figure 1 forms page 2 of this amendment. THIS DOCUMENT CONTAINS 3- PAGES. FSC 5826 8 o Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-I-38357A

7、 (3) 58 = 7777906 OL574LL T - / MIL-I-38357A (USAE) AMENDMENT 3 a FICURE 1. Dial und Poineers PAGE 2 Of 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-PAGE 16 Figure 2: Delete 11D-1103/ARN“ and substitute “ID-l103A/ARN“. PAGE 21 4.6.23, last line

8、: after “tests“, add “except burn-in“. 4.6.25, last line : Delete “3.4.2.2“ and substitute “3.4.1.2“. PAGE 22 5.3, line 3 : 6 1, line 1: Delete rrID-i103/ARN“ and substitute “ID-l103A/ARN“. Delete “ID-1103/ARNt1 and substitute “ID-i103A/ARN“. Add: “6.2.1 Case. When approved by the procuring activity

9、 (see 3.4.3), case dimensions previously approved under MIL-1-38357 may be used.“ Add: “6.2.2 Dial. When approved by the procuring activity (see 3.4.5), dial and pointer dimensions previously approved under MIL-1-38357 may be used“. Identification of changes: asterisk to indicate where changes (addi

10、tions, modifications, corrections, “The margins of this amendment are marked with an deletions) from the previous amendment were made. ience only and the Government assumes no liability whatsoever for any inaccur- acies in these notations. Bidders and contractors are cautioned to evaluate the requir

11、ements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous amendment.“ This was done as a conven- Change Custodian, Preparing Activity and Review Activity as follows: Custodian : Preparing At ivit y : Air Force - 99 Air Force - 99 Project No. 5826-F158 PAGE 3 of 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-