AASHTO M 233-1986 Standard Specification for Boiled Linseed Oil Mixture for Treatment of Portland Cement Concrete《处理硅酸盐水泥混凝土的熟炼亚麻油的标准规范》.pdf

《AASHTO M 233-1986 Standard Specification for Boiled Linseed Oil Mixture for Treatment of Portland Cement Concrete《处理硅酸盐水泥混凝土的熟炼亚麻油的标准规范》.pdf》由会员分享，可在线阅读，更多相关《AASHTO M 233-1986 Standard Specification for Boiled Linseed Oil Mixture for Treatment of Portland Cement Concrete《处理硅酸盐水泥混凝土的熟炼亚麻油的标准规范》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Standard Specification for Boiled Linseed Oil Mixture for Treatment of Portland Cement Concrete AASHTO Designation: M 233-86 (2014) American Association of State Highway and Transportation Officials 444 North Capitol Street N.W., Suite 249 Washington, D.C. 20001TS-4c M 233-1 AASHTO Standard Specific

2、ation for Boiled Linseed Oil Mixture for Treatment of Portland Cement Concrete AASHTO Designation: M 233-86 (2014) 1. SCOPE 1.1. This specification covers boiled linseed oil-petroleum spirits mixture to be applied to hardened portland cement concrete as a protection against damage by deicing chemica

3、ls. 1.2. The values stated in SI units are to be regarded as the standard. 2. REFERENCED DOCUMENTS 2.1. ASTM Standards: D56, Standard Test Method for Flash Point by Tag Closed Cup Tester D235, Standard Specification for Mineral Spirits (Petroleum Spirits) (Hydrocarbon Dry Cleaning Solvent) D260, Sta

4、ndard Specification for Boiled Linseed Oil (Withdrawn 2007) D1544, Standard Test Method for Color of Transparent Liquids (Gardner Color Scale) D1639, Standard Test Method for Acid Value of Organic Coating Materials (Withdrawn 2005) D1640/D1640M, Standard Test Methods for Drying, Curing, or Film Form

5、ation of Organic Coatings D1644, Standard Test Methods for Nonvolatile Content of Varnishes D1959, Standard Test Method for Iodine Value of Drying Oils and Fatty Acids (Withdrawn 2006) D1962, Standard Test Method for Saponification Value of Drying Oils, Fatty Acids, and Polymerized Fatty Acids (With

6、drawn 2004) D1963, Standard Test Method for Specific Gravity of Drying Oils, Varnishes, Resins, and Related Materials at 25/25C (Withdrawn 2004) 3. PROPERTIES 3.1. The compound shall consist of a homogeneous mixture of 50 percent boiled linseed oil and 50 percent petroleum spirits by volume. 3.2. Th

7、e boiled linseed oil shall conform to the requirements of ASTM D260, for Boiled Linseed Oil Type I or Type II. 3.3. The petroleum spirits shall conform to the requirements of ASTM D235, for Petroleum Spirits (Mineral Spirits). 2015 by the American Association of State Highway and Transportation Offi

8、cials.All rights reserved. Duplication is a violation of applicable law.TS-4c M 233-2 AASHTO 3.4. When requested by the purchaser, the manufacturer shall certify that the boiled linseed oil and petroleum spirits used in the mixture fully conform to the requirements specified in Sections 3.2 and 3.3,

9、 respectively. 3.5. The mixture shall have the following properties: Minimum Maximum Specific gravity 25/25C 0.84 0.88 Acid value 5 Nonvolatile by mass, percent 55 57 Drying time, h 16 Color, Gardner 13 Iodine value 90 Saponification 100 Flash point (T.C.C.) C (F) 37.8 (100) 4. METHODS OF TESTING 4.

10、1. The properties enumerated in this specification shall be determined in accordance with the following methods of test: 4.1.1. Specific GravityASTM D1963. 4.1.2. Acid ValueASTM D1639. 4.1.3. Nonvolatile ContentASTM D1644, Method A. 4.1.4. Drying TimeASTM D1640. 4.1.5. ColorASTM D1544. 4.1.6. Iodine ValueASTM D1959. 4.1.7. Saponification ValueASTM D1962. 4.1.8. Flash PointASTM D56. 2015 by the American Association of State Highway and Transportation Officials.All rights reserved. Duplication is a violation of applicable law.