ABS 9 CORR-2017 RULES FOR BUILDING AND CLASSING BULK CARRIERS FOR SERVICE ON THE GREAT LAKES 2017.pdf

《ABS 9 CORR-2017 RULES FOR BUILDING AND CLASSING BULK CARRIERS FOR SERVICE ON THE GREAT LAKES 2017.pdf》由会员分享，可在线阅读，更多相关《ABS 9 CORR-2017 RULES FOR BUILDING AND CLASSING BULK CARRIERS FOR SERVICE ON THE GREAT LAKES 2017.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、 RULES FOR BUILDING AND CLASSING BULK CARRIERS FOR SERVICE ON THE GREAT LAKES 2017 CORRIGENDA/EDITORIALS 10 April 2017 Page No. Paragraph Comments Part 3 Hull Construction and Equipment Chapter 1 General Section 2 General Requirements 19 3-1-2/Table 1 (metric units) In column 7 for length 253 m, “1.

2、1,0” to read “11.0”. 20 3-1-2/Table 1 (metric units) In Note 1, “0.01 in. for each in.” to read “1.0 mm for each 100 mm”. Part 3 Hull Construction and Equipment Chapter 2 Hull Structures and Arrangements Section 1 Longitudinal Strength 27 3-2-1/3.1.1 In equation for SM, “fv” to read “fp”. 27 3-2-1/3

3、.1.1 In definitions of terms “fv” to read “fp”. 28 3-2-1/3.1.1 In second line of last paragraph, “fv” to read “fp”. 29 3-2-1/3.3.1 In second line of second paragraph, “Msw” to read “Ms”. 29 3-2-1/3.3.1 In fourth equation for Ms, “3.86L” to read “3.867L”. 29 3-2-1/3.3.1 In definition of Ms, “moment:

4、amidships” to read “moment amidships”. 30 3-2-1/3.3.3 In sixth equation for Cw, “6993” to read “8993”. 30 3-2-1/3.3 Renumber “3.1.4” as “3.3.4”. 30 3-2-1/3.3.4 In equations for Msp, “(L/1000)2” and “(L/305)2” to read “(L/1000)3” and “(L/305)3”, respectively. 31 3-2-1/3.3.4 In definition of Csp, “5.0

5、6 ” to read “5.06/ ”. 31 3-2-1/3.3.4 In third equation for Cf, “1375” to read “1374”. 31 3-2-1/3.5.1 In definition of I, “about the hull girder section at the section tinder consideration” to read “of the hull girder section at the section under consideration”. 33 3-2-1/9.3 In definition of Q, “7090

6、0/Y + 2U/3)” to read “70900/(Y + 2U/3)”. 33 3-2-1/9.3 In definition of Q, “49.92/Y + 2U/3)” to read “49.92/(Y + 2U/3)”. 33 3-2-1/9.3 In definition of Y, “0,2%” to read “0.2%”. 36 3-2-1/Table 2 (Q = 1.0) In header, “0.8” to read “0.80”. 36 3-2-1/Table 2 (Q = 1.0) In row for L = 500 ft, value for 0.95

7、 to read “253”. 37 3-2-1/Table 2 (Q = 0.78) In header, “0.8” to read “0.80”. 37 3-2-1/Table 2 (Q = 0.78) In row for L = 780 ft, value for 0.85 to read “484”. ABSRULES FOR BUILDING AND CLASSING BULK CARRIERS FOR SERVICE ON THE GREAT LAKES .2017 1 Corrigenda/Editorials 10 April 2017 Page No. Paragraph

8、 Comments Part 3 Hull Construction and Equipment Chapter 2 Hull Structures and Arrangements Section 1 Longitudinal Strength 38 3-2-1/Table 2 (Q = 0.72) In header, “0.8” to read “0.80”. 38 3-2-1/Table 2 (Q = 0.72) In row for L = 900 ft, value for 0.85 to read “623”. 39 3-2-1/Table 2 (Q = 1.0) In head

9、er, “0.8” to read “0.80”. 39 3-2-1/Table 2 (Q = 1.0) In row for L = 220 m, value for 1.05 to read “3332”. 40 3-2-1/Table 2 (Q = 0.78) In header, “0.8” to read “0.80”. 40 3-2-1/Table 2 (Q = 0.78) In row for L = 185 m, value for 0.90 to read “1850”. 40 3-2-1/Table 2 (Q = 0.78) In row for L = 215 m, va

10、lue for 0.80 to read “2523”. 40 3-2-1/Table 2 (Q = 0.78) In row for L = 315 m, value for 1.05 to read “6023”. 41 3-2-1/Table 2 (Q = 0.72) In header, “0.8” to read “0.80”. 41 3-2-1/Table 2 (Q = 0.72) In row for L = 170 m, value for 1.00 to read “1449”. 41 3-2-1/Table 2 (Q = 0.72) In row for L = 170 m

11、, value for 1.05 to read “1447”. 41 3-2-1/Table 2 (Q = 0.72) In row for L = 230 m, value for 1.10 to read “2663”. Part 3 Hull Construction and Equipment Chapter 2 Hull Structures and Arrangements Section 3 Decks 45 3-2-3/7 In equations for SM, “in2” and “cm2” to read “in3” and “cm3”, respectively. 4

12、6 3-2-3/9.1 In equations for SM, “in2” and “cm2” to read “in3” and “cm3”, respectively. 46 3-2-3/9.7 In equations for SM, to “chs2” read “cs2”. 46 3-2-3/9.7 In equations for SM, “in2” and “cm2” to read “in3” and “cm3”, respectively. 46 3-2-3/9.7 In definitions, “l” to read “”. Part 3 Hull Constructi

13、on and Equipment Chapter 2 Hull Structures and Arrangements Section 4 Bottom Structure 50 3-2-4/13.3 In second line, “less than (760 mm)” to read “less than 30 in. (760 mm)”. 50 3-2-4/13.5 In equations for SM, “in2” and “cm2” to read “in3” and “cm3”, respectively. Part 3 Hull Construction and Equipm

14、ent Chapter 2 Hull Structures and Arrangements Section 5 Decks 52 3-2-5/7 In equations for SM, “in2” and “cm2” to read “in3” and “cm3”, respectively. 53 3-2-5/9 In equations for SM, “in2” and “cm2” to read “in3” and “cm3”, respectively. 53 3-2-5/11.1 In equations for SM, “in2” and “cm2” to read “in3

15、” and “cm3”, respectively. 2 ABSRULES FOR BUILDING AND CLASSING BULK CARRIERS FOR SERVICE ON THE GREAT LAKES .2017 Corrigenda/Editorials 10 April 2017 Page No. Paragraph Comments Part 3 Hull Construction and Equipment Chapter 2 Hull Structures and Arrangements Section 6 Design Pressure 57 3-2-6/7.3

16、In equations for SM, “in2” and “cm2” to read “in3” and “cm3”, respectively. 57 3-2-6/7.5.1 In equations for SM, “in2” and “cm2” to read “in3” and “cm3”, respectively. 59 3-2-6/Figure 1 (inch units) In Note, “0.6 in.” to read “0.06 in.”. 59 3-2-6/Figure 1 (inch units) In Note, “stiffener spacing, in

17、in.” to read “stiffener spacing, in ft”. Part 3 Hull Construction and Equipment Chapter 2 Hull Structures and Arrangements Section 7 Tank Boundary Bulkheads 61 3-2-7/3.3 In equations for SM, “in2” and “cm2” to read “in3” and “cm3”, respectively. 61 3-2-7/3.5.1 In equations for SM, “in2” and “cm2” to

18、 read “in3” and “cm3”, respectively. 63 3-2-7/Figure 1 (inch units) In Note, “stiffener spacing, in in.” to read “stiffener spacing, in ft”. 64 3-2-7/Figure 1 (metric units) In Note, “stiffener spacing, in in.” to read “stiffener spacing, in m”. Part 3 Hull Construction and Equipment Chapter 2 Hull

19、Structures and Arrangements Section 8 Superstructures and Deckhouses 65 3-2-8/1.3 Equations for SM, to read “0.0041cs2in3” and “7.9cs2cm3”, respectively. 65 3-2-8/1.3 In definition of , “ft or m” to read “ft (m)”. 66 3-2-8/1.7.2 In equations for SM, to “chs2” read “cs2”. 66 3-2-8/1.7.2 In equations

20、for SM, “in2” and “cm2” to read “in3” and “cm3”, respectively. 67 3-2-8/3.1.2 In equations for SM, to “chs2” read “cs2”. 67 3-2-8/3.1.2 In equations for SM, “in2” and “cm2” to read “in3” and “cm3”, respectively. Part 3 Hull Construction and Equipment Chapter 2 Hull Structures and Arrangements Sectio

21、n 9 Protection of Deck Openings 70 3-2-9/9.1 In third line, “position 2” to read “Position 2”. Part 3 Hull Construction and Equipment Chapter 2 Hull Structures and Arrangements Appendix 1 Calculation of Shear Stresses 73 3-2-A1/5 In equation for SWSF, “HK1” to read “NK1”. 73 3-2-A1/5 In definition o

22、f fs, reference “2.2.3” to read “3-2-1/3.5”. 73 3-2-A1/5 In definition of fd, reference “2.2.3b” to read “3-2-1/3.5.2”. ABSRULES FOR BUILDING AND CLASSING BULK CARRIERS FOR SERVICE ON THE GREAT LAKES .2017 3 Corrigenda/Editorials 10 April 2017 Page No. Paragraph Comments Part 3 Hull Construction and

23、 Equipment Chapter 3 Equipment Section 1 Anchoring, Mooring and Towing Equipment 78 3-3-1/Table 1 (inch/pound units) For Equipment Tonnage 7000, 7500, and 8000, value for normal strength steel to read “21/8”. 78 3-3-1/Table 1 (inch/pound units) For Equipment Tonnage 8500 and 9000, value for normal s

24、trength steel to read “23/16”. 78 3-3-1/Table 1 (inch/pound units) For Equipment Tonnage 9500, 10000, and 10750, value for normal strength steel to read “25/16”. 78 3-3-1/Table 1 (inch/pound units) For Equipment Tonnage 11500 and 12250, value for normal strength steel to read “23/8”. 4 ABSRULES FOR BUILDING AND CLASSING BULK CARRIERS FOR SERVICE ON THE GREAT LAKES .2017