BS PD ISO TS 13399-60-2014 Cutting tool data representation and exchange Reference dictionary for connection systems《切削工具数据表示和交换 连接系统用参考字典》.pdf

《BS PD ISO TS 13399-60-2014 Cutting tool data representation and exchange Reference dictionary for connection systems《切削工具数据表示和交换 连接系统用参考字典》.pdf》由会员分享，可在线阅读，更多相关《BS PD ISO TS 13399-60-2014 Cutting tool data representation and exchange Reference dictionary for connection systems《切削工具数据表示和交换 连接系统用参考字典》.pdf（152页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards Publication PD ISO/TS 13399-60:2014 Cutting tool data representation and exchange Part 60: Reference dictionary for connection systemsPD ISO/TS 13399-60:2014 PUBLISHED DOCUMENT National foreword This Published Document is the UK implementation of ISO/TS 13399-60:2014. It supersedes DD

2、ISO/TS 13399-60:2007 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee MTE/18, Tools tips and inserts for cutting applications. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not

3、purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2014. Published by BSI Standards Limited 2014 ISBN 978 0 580 82715 0 ICS 25.100.01; 35.240.50 Compliance with a British Standard cannot confer immunity

4、from legal obligations. This Published Document was published under the authority of the Standards Policy and Strategy Committee on 28 February 2014. Amendments issued since publication Date Text affectedPD ISO/TS 13399-60:2014 ISO 2014 Cutting tool data representation and exchange Part 60: Referenc

5、e dictionary for connection systems Reprsentation et change des donnes relatives aux outils coupants Partie 60: Dictionnaire de rfrence pour les systmes de connexion TECHNICAL SPECIFICATION ISO/TS 13399-60 Second edition 2014-02-15 Reference number ISO/TS 13399-60:2014(E)PD ISO/TS 13399-60:2014ISO/T

6、S 13399-60:2014(E)ii ISO 2014 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2014 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on th

7、e internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.o

8、rg Web www.iso.org Published in SwitzerlandPD ISO/TS 13399-60:2014ISO/TS 13399-60:2014(E) ISO 2014 All rights reserved iii Contents Page Foreword iv Introduction vi 1 Scope . 1 2 Normative references 2 3 T erms and definitions . 2 4 Abbreviated terms 5 5 Representation of the ontology concepts as di

9、ctionary entries 5 5.1 General . 5 5.2 connection interface feature . 5 6 Properties for connection interface feature 8 6.1 General . 8 6.2 Definition of the structure of connection interface code 9 6.3 Representation of connection interface code 12 6.4 Representation of insert interface code .15 An

10、nex A (normative) Information object registration .27 Annex B (informative) Classification table28 Annex C (informative) Class definitions .37 Annex D (informative) C onnection int erfac e featur e pr operty definitions 87 Annex E (informative) Illustrations of connection systems .92 Bibliography .1

11、38PD ISO/TS 13399-60:2014ISO/TS 13399-60:2014(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each

12、member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International

13、 Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different t

14、ypes of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not

15、be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is info

16、rmation given for the convenience of users and does not constitute an endorsement. For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see

17、the following URL: Foreword - Supplementary information The committee responsible for this document is ISO/TC 29, Small Tools. This second edition cancels and replaces the first edition (ISO/TS 13399-60:2007), which has been technically revised. The following are the main changes: subclauses for con

18、nection interface features have been added in 5.2; Clause 6 has been revised. ISO 13399 consists of the following parts, under the general title Cutting tool data representation and exchange: Part 1: Overview, fundamental principles and general information model Part 2: Reference dictionary for cutt

19、ing items Technical Specification Part 3: Reference dictionary for tool items Technical Specification Part 4: Reference dictionary for adaptive items Technical Specification Part 5: Reference dictionary for assembly items Technical Specification Part 50: Reference dictionary for reference systems an

20、d common concepts Technical Specification Part 60: Reference dictionary for connection systems Technical Specification Part 100: Definitions, principles and methods for reference dictionaries Technical Specification Part 150: Usage guidelines Technical Specification Part 301:Concept for the design o

21、f 3D models based on properties according to ISO/TS 133993: Modelling of thread cutting taps, thread forming taps and thread cutting dies Technical Specification Part 302:Concept for the design of 3D models based on properties according to ISO/TS 13399-3: Modelling of solid drills and countersinking

22、 tools Technical Specificationiv ISO 2014 All rights reservedPD ISO/TS 13399-60:2014ISO/TS 13399-60:2014(E) The following parts are under preparation: Part 51: Designation system for customer solution cutting tools Part 80: Concept for the design of 3D models based on properties according to ISO 133

23、99: Overview and principles Technical Specification Part 201: Concept for the design of 3D models based on properties according to ISO/TS 133992: Modelling of regular inserts Technical Specification Part 202: Concept for the design of 3D models based on properties according to ISO/TS 133992: Modelli

24、ng of irregular inserts Technical Specification Part 203: Concept for the design of 3D models based on properties according to ISO/TS 133992: Modelling of exchangeable inserts for drilling Technical Specification Part 204: Concept for the design of 3D models based on properties according to ISO/TS 1

25、33992: Modelling of inserts for reaming Technical Specification Part 303: Concept for the design of 3D models based on properties according to ISO/TS 133993: Modelling of end mills with non indexable cutting edges Technical Specification Part 304: Concept for the design of 3D models based on propert

26、ies according to ISO/TS 133993: Modelling of milling cutters with arbor hole and non indexable cutting edges Technical Specification Part 307: Concept for the design of 3D models based on properties according to ISO/TS 133993: Modelling of end mills for indexable inserts Technical Specification Part

27、 308: Concept for the design of 3D models based on properties according to ISO/TS 133993: Modelling of milling cutter with arbor hole for indexable inserts Technical Specification Part 309: Concept for the design of 3D models based on properties according to ISO/TS 133993: Tool holders for indexable

28、 inserts Technical Specification Part 311: Concept for the design of 3D models based on properties according to ISO/TS 133993: Modelling of solid reamers Technical Specification Part 312: Concept for the design of 3D models based on properties according to ISO/TS 133993: Modelling of reamers for ind

29、exable inserts Technical Specification Part 401: Concept for the design of 3D models based on properties according to ISO/TS 133994: Modelling of converting, extending and reducing adaptive items Technical Specification Part 405: Concept for the design of 3D models based on properties according to I

30、SO/TS 133994: Modelling of collets Technical Specification ISO 2014 All rights reserved vPD ISO/TS 13399-60:2014ISO/TS 13399-60:2014(E) Introduction This part of ISO 13399 defines the terms, properties, and definitions for connection systems of cutting tools with defined cutting edges. The purpose o

31、f this part of ISO 13399 is to provide a reference dictionary to support the use of the general information model in ISO 13399-1. A cutting tool with defined cutting edges is used on a machine to remove material from a workpiece by a shearing action at the cutting edges of the tool. Cutting tool dat

32、a that can be described by ISO 13399 (all parts) include, but are not limited to, everything between the workpiece and the machine tool. Information about inserts (e.g. regular and irregular shaped replaceable cutting items), solid tools (e.g. solid drill and endmill), assembled tools (e.g. boring b

33、ars, indexable drills, and indexable milling cutters), adaptors (e.g. milling arbor and drilling chuck), components (e.g. shims, screws, and clamps), and their relationships can be represented by ISO 13399 (all parts). Possible assemblies of the components of a cutting tool are illustrated in Figure

34、 1. The objective of ISO 13399 (all parts) is to provide the means to represent the information that describes cutting tools in a computer-sensible form that is independent from any computer system. The representation will facilitate the processing and exchange of cutting tool data within and betwee

35、n different software systems and computer platforms and support the application of this data in manufacturing planning, cutting operations, and the supply of tools. The nature of this description makes it suitable not only for neutral file exchange, but also as a basis for implementing and sharing p

36、roduct databases and for archiving. The methods used for these representations are those developed by ISO/TC 184/SC 4 for the representation of product data by using standardized information models and reference dictionaries. An information model is a formal specification of types, ideas, facts, and

37、 processes which together describe a portion of interests of the real world and which provides an explicit set of interpretation rules. Information is knowledge of ideas, facts, and/or processes. Data are symbols or functions that represent information for processing purposes. Data are interpreted t

38、o extract information by using rules for how that should be done and a dictionary to define the terms that identify the data items. Everyone in a communication process is expected to use the same information model, the same set of explicit rules, and the same dictionary in order to avoid misundersta

39、nding. If an information model and its dictionary are written in a computer-sensible language, then there is the additional benefit that they can be computer processable. An engineering information model is therefore a specification for data that establishes the meaning of that data in a particular

40、engineering context. A model has to be developed by formal methods to ensure that it meets the needs of the situation that it represents. An engineering information model defines the information objects that represent the concepts in an engineering application, the attributes of the objects, their r

41、elationships, and the constraints that add further meaning. An information model is an abstract concept that can be used repeatedly for any example of the real-world situation that it represents. An instance of the model is created when it is populated with the data items and their values that are a

42、pplicable to a particular example of that situation. This part of ISO 13399 uses the following International Standards developed by ISO/TC 184/SC 4: the EXPRESS language defined in ISO 10303-11 for defining the information model in ISO 13399-1; the file format for data exchange derived from the mode

43、l and defined in ISO 10303-21; the data dictionary defined in the ISO 13584 series. The ISO 13399 series is intended for use by, among others, tool producers and vendors, manufacturers, and developers of manufacturing software. ISO 13399 provides a common structure for exchanging data about cutting

44、tools with defined cutting edges. ISO 13399 is intended to provide for, or improve, several manufacturing activities, including the integration and sharing of data for cutting tools and assemblies between different stages for the manufacturing cycle and between different software applications,vi ISO

45、 2014 All rights reservedPD ISO/TS 13399-60:2014ISO/TS 13399-60:2014(E) the direct import of data from cutting tool suppliers into a customers database, and the management of cutting tool information from multiple sources and for multiple applications. Different companies use different business mode

46、ls that determine their need for the communication of information about their products. For example, one cutting tool manufacturer can regrind its customers tools while another could allow its customers to do the regrinding and provide the information to enable them to do so. Therefore, the two cutt

47、ing tool manufacturers can have a different set of cutting tool properties to communicate using the information model and dictionaries provided in ISO 13399. ISO 13399 only defines the information that could be communicated, but does not specify what information shall be communicated. Figure 1 Examp

48、le of different types of assemblies of items Since the content of those dictionaries evolves according to industrial innovations and constant improvement of technology in cutting tools, a Maintenance Agency has been established for the purposes of correcting errors in the entries of existing classes

49、 and properties, adding new properties to existing classes, adding new classes and their properties, managing the status of those properties and classes, and migrating the dictionary to subsequent editions of ISO 13399 (all parts). The secretariat of this Maintenance Agency has been assigned to:Union de Normalisation de la Mcanique ISO 2014 All rights reserved viiPD ISO/TS 13399-60:2014ISO/TS 13399-60:201