BS ISO 687-2010 en_5154 Solid mineral fuels Coke Determination of moisture in the general analysis test sample《固体矿物燃料.焦炭.一般分析试样中水分的测定》.pdf

《BS ISO 687-2010 en_5154 Solid mineral fuels Coke Determination of moisture in the general analysis test sample《固体矿物燃料.焦炭.一般分析试样中水分的测定》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 687-2010 en_5154 Solid mineral fuels Coke Determination of moisture in the general analysis test sample《固体矿物燃料.焦炭.一般分析试样中水分的测定》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwide NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BSI Standards Publication BS ISO 687:2010 Solid mineral fuels Coke Determination of moisture in the general analysis test sampleBS ISO 687:2010 BRITISH STANDARD National foreword This British Standard

2、is the UK implementation of ISO 687:2010. It supersedes BS ISO 687:2004 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee PTI/16, Solid mineral fuels. A list of organizations represented on this committee can be obtained on request to its secretary. Thi

3、s publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. BSI 2010 ISBN 978 0 580 70437 6 ICS 75.160.10 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published

4、 under the authority of the Standards Policy and Strategy Committee on 30 November 2010. Amendments issued since publication Date Text affectedBS ISO 687:2010Reference number ISO 687:2010(E) ISO 2010INTERNATIONAL STANDARD ISO 687 Third edition 2010-06-15 Solid mineral fuels Coke Determination of moi

5、sture in the general analysis test sample Combustibles mineraux solides Coke Dtermination de lhumidit de lchantillon pour analyse BS ISO 687:2010 ISO 687:2010(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewe

6、d but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in t

7、his area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable fo

8、r use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2010 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized

9、 in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41

10、 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2010 All rights reservedBS ISO 687:2010 ISO 687:2010(E) ISO 2010 All rights reserved iiiContents Page Foreword iv Introduction.v 1 Scope1 2 Normative references1 3 Definitions 1 4 Principle1 5 Apparatus.1 6 Prepara

11、tion of the test sample.2 7 Procedure.2 8 Expression of results2 9 Precision.3 10 Test report3 BS ISO 687:2010 ISO 687:2010(E) iv ISO 2010 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies).

12、The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-g

13、overnmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2

14、. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a

15、vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 687 was prepared by Technical Committee ISO/TC 27, Solid mineral fuels, Subcommittee SC 5,

16、Methods of analysis. This third edition cancels and replaces the second edition (ISO 687:2004), of which it constitutes a minor revision. BS ISO 687:2010 ISO 687:2010(E) ISO 2010 All rights reserved vIntroduction The determination of the moisture in the general analysis test sample is required to co

17、rrect the results of certain analytical determinations, e.g. volatile matter and hydrogen, for the effect of water in the determination and to allow all determinations to be corrected to a dry basis. Since coke is hygroscopic, its moisture varies with a change in humidity of the atmosphere, and it i

18、s required, therefore, that the moisture in the general analysis test sample be determined whenever portions are weighed out for other analytical determinations. If test portions for several analytical determinations are weighed out at the same time, a single simultaneous moisture determination suff

19、ices to correct these analyses. BS ISO 687:2010BS ISO 687:2010 INTERNATIONAL STANDARD ISO 687:2010(E) ISO 2010 All rights reserved 1Solid mineral fuels Coke Determination of moisture in the general analysis test sample 1 Scope This International Standard specifies a method for determining the moistu

20、re in the general analysis test sample of coke. It can be used for the determination of moisture in blast-furnace coke, foundry-coke and other high-temperature carbonization products. 2 Normative references The following referenced documents are indispensable for the application of this document. Fo

21、r dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 1213-2, Solid mineral fuels Vocabulary Part 2: Terms relating to sampling, testing and analysis 3 Definitions For the purposes of this Int

22、ernational Standard, the definitions given in ISO 1213-2 apply. 4 Principle A known mass of the coke is heated in air at 120 C to 200 C and maintained at this temperature until a constant mass is obtained. The moisture content is calculated from the loss in mass of the coke. Coke is not liable to ox

23、idation under the conditions stated. 5 Apparatus 5.1 Analytical balance, capable of weighing to the nearest 0,1 mg. 5.2 Oven, capable of being controlled at a temperature of 120 C to 200 C and with a means to allow a flow of air or nitrogen. 5.3 Weighing dish, shallow, of glass or of corrosion-resis

24、tant metal, with a well fitting cover, of such a size that the coke layer does not exceed 0,20 g/cm 2 . 5.4 Cooling vessel, e.g. desiccator, without desiccant, containing a porcelain or a metal plate, preferably of aluminium or copper. The vessel may be provided with the means to pass air or nitroge

25、n through it during the cooling period. BS ISO 687:2010 ISO 687:2010(E) 2 ISO 2010 All rights reserved6 Preparation of the test sample The coke used for the determination of moisture content is the general analysis test sample (see ISO 1213-2). Ensure that the moisture content of the sample is in eq

26、uilibrium with the laboratory atmosphere, exposing it, if necessary, in a thin layer for the minimum time required to achieve equilibrium. Before commencing the determination, thoroughly mix the equilibrated test sample for at least 1 min, preferably by mechanical means. 7 Procedure Weigh a clean, d

27、ry, empty weighing dish with its cover to the nearest 0,1 mg. Add 1 g 0,1 g of the coke sample in an even layer and reweigh. Heat the uncovered dish in the oven at 120 C to 200 C. When the drying period is complete, remove the dish with the dried sample from the oven and replace the cover immediatel

28、y. If the size of the oven allows, replace the cover while the dish is still in the oven. Allow the dish to cool on a thick metal plate for 10 min. At the end of the 10 min cooling period, transfer the dish to a cooling vessel (5.4) and allow to cool to room temperature. As soon as room temperature

29、is reached, reweigh to the nearest 0,1 mg. NOTE 1 If a cooling vessel with air or nitrogen flow is used the dish can be transferred directly without cooling on a metal plate. If there is any doubt that drying is complete, reheat at 120 C to 200 C for further 30 min periods until the change in mass b

30、etween successive weighings does not exceed 1 mg. For a particular oven, the times required to ensure constancy in mass shall be verified by experiments. NOTE 2 Heating for 4 h is normally sufficient. The time taken for the determination can be considerably shortened if drying is carried out at a te

31、mperature of 320 C in a nitrogen atmosphere, when heating for 1 h usually suffices. For this procedure, a minimum free space oven may be used. If appropriate, the drying can be done at lower temperature, e.g. 105 C to 110 C, as for hard coal. It is necessary to verify by experiments the times requir

32、ed to ensure constancy in mass. 8 Expression of results The moisture in the coke as analysed, H 2 O,ad , expressed as a percentage mass fraction is given by Equation (1): 2 23 HO , a d 21 100 mm mm = (1) where m 1is the mass, expressed in grams, of the empty dish plus cover; m 2is the mass, expresse

33、d in grams, of the dish plus cover plus coke before heating; m 3is the mass, expressed in grams, of the dish plus cover plus coke after heating. Report the result, as the mean of duplicate determinations, to the nearest 0,1 % mass fraction. BS ISO 687:2010 ISO 687:2010(E) ISO 2010 All rights reserve

34、d 39 Precision 9.1 Repeatability limit The results of duplicate determinations (carried out over a short period of time, but not simultaneously) in the same laboratory, by the same operator, with the same apparatus on two representative portions taken from the same analysis sample, should not differ

35、 by more than the values shown in Table 1. 9.2 Reproducibility limit Since the humidity conditions in different laboratories vary, it is not practical to quote a limiting value for reproducibility. Table 1 Precision of moisture determination Maximum acceptable differences between results Repeatabili

36、ty limit Reproducibility limit 0,2 % absolute See 9.2 10 Test report The test report shall include the following information: a) reference to this International Standard, i.e. ISO 687; b) identification of the sample tested; c) results of the determination; d) date of the determination. BS ISO 687:2

37、010 ISO 687:2010(E) ICS 75.160.10 Price based on 3 pages ISO 2010 All rights reserved This page deliberately left blankBSI is the independent national body responsible for preparing British Standards and other standards-related publications, information and services. It presents the UK view on stand

38、ards in Europe and at the international level. It is incorporated by Royal Charter. British Standards Institution (BSI) raising standards worldwide BSI Group Headquarters 389 Chiswick High Road London W4 4AL UK Tel +44 (0)20 8996 9001 Fax +44 (0)20 8996 7001 British Standards are updated by amendme

39、nt or revision. Users of British Stan- dards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and serv- ices. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard

40、would inform the Secretary of the technical com- mittee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001 BSI offers Members an individual updating service called PLUS which ensures that subscribers automatically receive the

41、latest editions of standards. Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001 Email: Buying standards You may buy PDF and hard copy versions of standards directly using a credit card from the BSI Shop on the website In addition all orders for BSI, international and foreign standards publications

42、 can be addressed to BSI Customer Services. Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001 Email: In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information o

43、n standards BSI provides a wide range of information on national, European and international standards through its Knowledge Centre. Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005 Email: Various BSI electronic information services are also available which give details on all its products and ser

44、vices. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: BSI Subscribing Members are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Ad- ministration. Tel: +44 (0)20 8

45、996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via British Standards Online can be found at Further information about BSI is available on the BSI website at www.bsi- Copyright Copyright subsists in all BSI publications. BSI also holds the copyrig

46、ht, in the UK, of the publications of the international standardization bodies. Ex- cept as permitted under the Copyright, Designs and Patents Act 1988 no ex- tract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or other

47、wise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copy- right & Licensing Manager. Tel: +44 (0)20 8996 7070 Email: