EN 477-2018 Plastics - Poly(vinyl chloride) (PVC) based profiles - Determination of the resistance to impact of profiles by falling mass.pdf

《EN 477-2018 Plastics - Poly(vinyl chloride) (PVC) based profiles - Determination of the resistance to impact of profiles by falling mass.pdf》由会员分享，可在线阅读，更多相关《EN 477-2018 Plastics - Poly(vinyl chloride) (PVC) based profiles - Determination of the resistance to impact of profiles by falling mass.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06Plastics - Poly(vinyl chloride) (PVC) based profiles - Determination of the resistance to impact of profiles by falling massBS EN 477:2018National forewordThis British Standard is the UK implementation of EN 477:2018. I

2、t supersedes BS EN 477:1999, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee PRI/21, Testing of plastics.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all

3、the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2018 Published by BSI Standards Limited 2018ISBN 978 0 580 94816 9ICS 83.140.99; 91.060.50Compliance with a British Standard cannot confer immunity from legal obligations. Thi

4、s British Standard was published under the authority of the Standards Policy and Strategy Committee on 28 February 2018.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 477:2018EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 477January 2018ICS 83.080.20; 83.140

5、.99 Supersedes EN 477:1995EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGCEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2018 CEN Ref. No. EN 477:2018: EAll rights of exploitation in any form and by any means reserved worldwide for

6、CEN national MembersPlastics - Poly(vinyl chloride) (PVC) based profiles - Determination of the resistance to impact of profiles by falling massPlastiques - Profils base de poly(chlorure de vinyle) (PVC) - Dtermination de la rsistance aux chocs par masse tombante des profilsKunststoffe - Profile auf

7、 Basis von Polyvinylchlorid (PVC) - Bestimmung der Stofestigkeit von Profilen mittels FallbolzensThis European Standard was approved by CEN on 6 December 2017.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard th

8、e status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.This European Standard exists in three official versions (English, Frenc

9、h, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, C

10、roatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, T

11、urkey and United Kingdom.English VersionEN 477:2018 (E)European foreword 31 Scope . 42 Normative references 43 Terms and definitions . 44 Principle 45 Apparatus . 46 Test specimens 47 Conditioning 68 Procedure. 69 Expression of results 610 Test report . 62Contents PageBS EN 477:2018EN 477:2018 (E)Eu

12、ropean forewordThis document (EN 477:2018) has been prepared by Technical Committee CEN/TC 249 “Plastics”, the secretariat of which is held by NBN.This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by J

13、uly2018, and conflicting national standards shall be withdrawn at the latest by July 2018.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN not be held responsible for identifying any or all such patent rights.This document supe

14、rsedes EN 477:1995.According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Mac

15、edonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.3BS EN 477:2018EN 477:2018 (E)1 ScopeThis European Standard s

16、pecifies a method for determining the resistance to impact by a falling mass at 10 C of unplasticized poly(vinyl chloride) (PVC-U) profiles.It is also applicable to PVC-based profiles at specified temperatures/test conditions.2 Normative referencesThere are no normative references in this document.3

17、 Terms and definitionsFor the purposes of this document, the following terms and definitions apply.ISO and IEC maintain terminological databases for use in standardization at the following addresses: IEC Electropedia: available at http:/www.electropedia.org/ ISO Online browsing platform: available a

18、t http:/www.iso.org/obp3.1inner webpartition wall connecting two walls of a profile4 PrincipleTest specimens cut from lengths of profiles are subjected to a blow from a mass falling from a known height on the surface at a point mid-way between two inner webs at a fixed temperature.After testing the

19、profiles are examined visually for failures in the surface tested.5 ApparatusAn impact testing machine incorporating the following basic components (see Figure 1) shall be used:a) main frame, rigidly fixed in the vertical position;b) guide rails, fixed to the main frame to accommodate the falling ma

20、ss and allowing it to fall freely in the vertical plane;c) test specimen support, consisting of two rounded off supports (see Figure 2) (200 1) mm apart. The support shall be made from steel and rigidly fixed in a solid foundation or on a table with a mass of more than 50 kg;d) release mechanism, su

21、ch that the falling height of the mass, measured from the top surface of the test specimen to be tested, can be adjusted up to the falling height defined in the referred product standard with a tolerance of ( ) mm (e.g. 1 000 mm, 1 500 mm);e) falling mass, of (1 000 5) g, which has a hemispherical s

22、triking surface of (25 0,5) mm radius.The striking surface shall be free from all imperfections.6 Test specimensTen test specimens, each of length of 300 mm shall be taken from a profile.4 BS EN 477:2018EN 477:2018 (E)Key1 falling massFigure 1 Example of impact resistance testing apparatusDimensions

23、 in millimetresFigure 2 Example of a supporting device5BS EN 477:2018EN 477:2018 (E)7 ConditioningThe test specimens shall be conditioned at a temperature of ( ) C for at least 1 h before testing.Each test specimen shall be tested within 10 s of removal from the conditioning chamber.8 Procedure8.1 T

24、he test shall be performed on the surface of the profile, as defined by the referred standard.8.2 Drop the falling mass from the given height as required in the product standard at a point mid-way between two inner webs.Where it is impracticable for the mass to hit the profile in accordance to the a

25、bove due to its geometry other impact positions for the falling mass should be agreed upon between the profile manufacturer and the testing laboratory.When due to its geometry, the profile tend to tilt sideways at the impact of the falling mass, any tilting should be prevented, by attaching addition

26、al stays to the two supports.During the test care should be taken to prevent multiple impacts of the falling mass on the test specimen.9 Expression of resultsThe number of test specimens tested and the number of test specimens broken shall be reported for each type of profile.10 Test reportThe test

27、report shall include the following information:a) reference to this document (i.e. EN 477);b) the testing laboratory;c) full identification of the profile;d) date of testing;e) the height of the falling mass;f) the number of test specimens tested;g) the number of test specimens broken;h) all operati

28、ng details not specified in this document, as well as incidents likely to have influenced the results.6 BS EN 477:2018This page deliberately left blankThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, infor

29、mation and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)About usWe bring together business, industry, government, consumers, innovators and others to shape their combined

30、experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.

31、Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publicati

32、ons, including British and adopted European and international standards, through our website at where hard copies can also be purchased.If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.Copyrigh

33、t in BSI publicationsAll the content in BSI publications, including British Standards, is the property of and copyrighted by BSI or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI f

34、or commercial publication and use.Save for the provisions below, you may not transfer, share or disseminate any portion of the standard to any other person. You may not adapt, distribute, commercially exploit, or publicly display the standard or any portion thereof in any manner whatsoever without B

35、SIs prior written consent.Storing and using standardsStandards purchased in soft copy format: A British Standard purchased in soft copy format is licensed to a sole named user for personal or internal company use only. The standard may be stored on more than 1 device provided that it is accessible b

36、y the sole named user only and that only 1 copy is accessed at any one time. A single paper copy may be printed for personal or internal company use only. Standards purchased in hard copy format: A British Standard purchased in hard copy format is for personal or internal company use only. It may no

37、t be further reproduced in any format to create an additional copy. This includes scanning of the document.If you need more than 1 copy of the document, or if you wish to share the document on an internal network, you can save money by choosing a subscription product (see Subscriptions).Reproducing

38、extractsFor permission to reproduce content from BSI publications contact the BSI Copyright & Licensing team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL

39、) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date.You can keep in touch with standards developments and receive substantial discounts on the purchase price of

40、standards, both in single copy and subscription format, by becoming a BSI Subscribing Member.PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced.To find out more about becoming a BSI S

41、ubscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentat

42、ion is current. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or ot

43、her BSI publication please inform the Knowledge Centre.Useful ContactsCustomer ServicesTel: +44 345 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 345 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: BSI Group Headquarters389 Chiswick High Road London W4 4AL UKNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW