ISO 16537-2012 Thermal insulating products for building applications - Determination of shear behaviour《建筑应用件用建筑物保温制品 剪切特性的测定》.pdf

《ISO 16537-2012 Thermal insulating products for building applications - Determination of shear behaviour《建筑应用件用建筑物保温制品 剪切特性的测定》.pdf》由会员分享，可在线阅读，更多相关《ISO 16537-2012 Thermal insulating products for building applications - Determination of shear behaviour《建筑应用件用建筑物保温制品 剪切特性的测定》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、 ISO 2012 Thermal insulating products for building applications Determination of shear behaviour Produits isolants thermiques destins aux applications du btiment Dtermination du comportement en cisaillement INTERNATIONAL STANDARD ISO 16537 First edition 2012-05-15 Reference number ISO 16537:2012(E)

2、ISO 16537:2012(E) ii ISO 2012 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2012 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without perm

3、ission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ISO 16537:2012(E) ISO 2012

4、All rights reserved iii Contents Page Foreword iv Introduction v 1 Scope 1 2 Normative references . 1 3 T erms and definitions . 1 4 Principle . 1 5 Apparatus 2 5.1 Test machine . 2 5.2 Specimen supports . 2 5.3 Adhesive 3 6 Test specimens 5 6.1 Dimensions of test specimens 5 6.2 Number of test spec

5、imens 6 6.3 Preparation of test specimens . 6 6.4 Conditioning of test specimens 6 7 Procedure 6 7.1 Test conditions . 6 7.2 Test procedure . 6 8 Calculation and expression of results . 7 8.1 General . 7 8.2 Shear strength 7 8.3 Shear modulus . 7 9 Accuracy of measurement 8 10 Test report . 8 ISO 16

6、537:2012(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject f

7、or which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on

8、 all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees a

9、re circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held

10、responsible for identifying any or all such patent rights. ISO 16537 was prepared by Technical Committee ISO/TC 163, Thermal performance and energy use in the built environment, Subcommittee SC 1, Test and measurement methods. ISO 16537 includes the original EN 12090 prepared by Technical Committee

11、CEN/TC 88 “Thermal insulating materials and products”, with the following clauses modified to reflect the conditions for tropical countries: Clause 6.4: Conditioning of test specimens; Clause 7.1: Test conditions; and Clause 10: Test report. iv ISO 2012 All rights reserved ISO 16537:2012(E) Introduc

12、tion ISO 16537 is one of a series of existing European Standards on test methods which were adopted by ISO. This group of International Standards comprises the following group of interrelated standards: ISO Title Respective EN standard 12344 Thermal insulating products for building applications Dete

13、rmination of bending behaviour EN 12089 12968 Thermal insulation products for building applications Determination of the pull-off resistance of external thermal insulation composite systems (ETICS) (foam block test) EN 13495 29465 Thermal insulating products for building applications Determination o

14、f length and width EN 822 29466 Thermal insulating products for building applications Determination of thickness EN 823 29467 Thermal insulating products for building applications Determination of squareness EN 824 29468 Thermal insulating products for building applications Determination of flatness

15、 EN 825 29469 Thermal insulating products for building applications Determination of compression behaviour EN 826 29470 Thermal insulating products for building applications Determination of the apparent density EN 1602 29471 Thermal insulating products for building applications Determination of dim

16、ensional stability under constant normal laboratory conditions (23 degrees C/50 % relative humidity) EN 1603 29472 Thermal insulating products for building applications Determination of dimensional stability under specified temperature and humidity conditions EN 1604 29764 Thermal insulating product

17、s for building applications Determination of deformation under specified compressive load and temperature conditions EN 1605 29765 Thermal insulating products for building applications Determination of tensile strength perpendicular to faces EN 1607 29766 Thermal insulating products for building app

18、lications Determination of tensile strength parallel to faces EN 1608 29767 Thermal insulating products for building applications Determination of short- term water absorption by partial immersion EN 1609 29768 Thermal insulating products for building applications Determination of linear dimensions

19、of test specimens EN 12085 29769 Thermal insulating products for building applications Determination of behaviour under point load EN 12430 29770 Thermal insulating products for building applications Determination of thickness for floating-floor insulating products EN 12431 ISO 2012 All rights reser

20、ved v ISO 16537:2012(E) 29771 Thermal insulating materials for building applications Determination of organic content EN 13820 29803 Thermal insulation products for building applications Determination of the resistance to impact of external thermal insulation composite systems (ETICS) EN 13497 29804

21、 Thermal insulation products for building applications Determination of the tensile bond strength of the adhesive and of the base coat to the thermal insulation material EN 13494 29805 Thermal insulation products for building applications Determination of the mechanical properties of glass fibre mes

22、hes EN 13496 16534 Thermal insulating products for building applications Determination of compressive creep EN 1606 16535 Thermal insulating products for building applications Determination of long- term water absorption by immersion EN 12087 16536 Thermal insulating products for building applicatio

23、ns Determination of long- term water absorption by diffusion EN 12088 16537 Thermal insulating products for building applications Determination of shear behaviour EN 12090 16546 Thermal insulating products for building applications Determination of freeze- thaw resistance EN 12091 16544 Thermal insu

24、lating products for building applications Conditioning to moisture equilibrium under specified temperature and humidity conditions EN 12429 16545 Thermal insulating products for building applications Determination of behaviour under cyclic loading EN 13793 A further group of existing European Standa

25、rds on test methods for products used to insulate building equipment and industrial installations comprises the following group of interrelated International Standards: ISO 12623 Thermal insulating products for building equipment and industrial installations Determination of short-term water absorpt

26、ion by partial immersion of preformed pipe insulation EN 13472 ISO 12624 Thermal insulating products for building equipment and industrial installations Determination of trace quantities of water soluble chloride, fluoride, silicate, sodium ions and pH EN 13468 ISO 12628 Thermal insulating products

27、for building equipment and industrial installations Determination of dimensions, squareness and linearity of preformed pipe insulation EN 13467 ISO 12629 Thermal insulating products for building equipment and industrial installations Determination of water vapour transmission properties of preformed

28、 pipe insulation EN 13469 vi ISO 2012 All rights reserved INTERNATIONAL STANDARD ISO 16537:2012(E) Thermal insulating products for building applications Determination of shear behaviour 1 Scope This International Standard specifies the equipment and procedures for determining shear behaviour. It is

29、applicable to thermal insulating products. NOTE The tests described in this International Standard do not determine pure shear behaviour, but measure the effects of applying two opposite parallel forces to the major faces of the test specimen. The test is, however, called “shear” in this text by con

30、vention. The application of a force tangentially to the major surface of the test specimen is considered to represent more closely the stresses imposed upon thermal insulation products in many building applications, particularly walls, than other methods of measuring shear performance, e.g. bending

31、tests. 2 Normative references The following referenced document is indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 29768, Thermal in

32、sulating products for building applications Determination of linear dimensions of test specimens 3 T erms and definitio ns For the purposes of this document, the following definitions apply. 3.1 shear strength ratio of the maximum force applied to the product, which will cause rupture along a plane

33、parallel to the direction of the applied force, to the area of the plane on which the force acts 3.2 shear modulus G shear stress divided by the corresponding relative deformation below the proportional limit, when the relationship is linear NOTE See Figure 3. 4 Principle A test specimen is subjecte

34、d to a shear stress transmitted to the test specimen through rigid supports to which it is bonded. The corresponding force-displacement curve is determined. NOTE Tests carried out using the single test specimen method have produced results for shear strength which indicate the result to be dependent

35、 upon test specimen thickness, with more scattered results at greater thicknesses. Tests using the double test specimen method have also shown test specimen thickness to influence results for shear strength. ISO 2012 All rights reserved 1 ISO 16537:2012(E) 5 Apparatus 5.1 Test machine 5.1.1 General

36、A test machine capable of applying a sufficient force within the maximum displacement experienced in the shear test. It shall be capable of operating at a constant rate of movement of the movable head of (3 0,5) mm/min in a direction parallel to the longitudinal axis of the test specimen assembly. T

37、he test machine shall exert a force F on the test specimen with a maximum error of 1 %, and produce a displacement, , of the movable support relative to the fixed supports, having a maximum error of 1 %. If the shear modulus is required, the force F and the displacement shall be simultaneously recor

38、ded to provide the curve of F, required in Clause 7. NOTE 1 It may be necessary to use a displacement transducer for accurate measurement of deformation, particularly where a thick adhesive layer has been used in preparing the test specimen. The null or zero displacement of the test specimen may be

39、calculated by subtraction from , the displacement due to the equipment and the same thickness of adhesive measured without the test specimen, e.g. by replacing the test specimen by metal block(s) in a blank test. 5.1.2 Single test specimen arrangement The test machine shall exert longitudinal shear

40、forces through parallel plates bonded to a single test specimen of dimensions as in 6.1.2. The parallel plates shall be rigid with one plate attached to the fixed part and the other to the movable parts of the test machine. 5.1.3 Double test specimen arrangement The test machine shall exert longitud

41、inal shear forces through parallel plates bonded to a double test specimen of dimensions as in 6.1.3. The parallel plates shall be rigid with the outer plates attached to the fixed part and the central plate to the movable parts of the test machine. 5.2 Specimen supports 5.2.1 Single test specimen a

42、ssembly Two flat rigid specimen supports of length 330 mm and width 50 mm shall be attached to the grips of the test machine via an adaptor and universal joint. The method of attaching the specimen supports to the grips is shown in Figure 1. The thickness of the adaptors that connect the specimen su

43、pports to the test machine grips shall be the same as the thickness of the test specimen. NOTE Flat rectangular sectioned mild steel plates with a thickness of 16 mm have proved suitable for the support material. 5.2.2 Double test specimen assembly The essential features are three flat rigid support

44、s of which two can be maintained with their planes parallel and vertical. Two suitable arrangements are shown in Figure 2. Experience gained using both the single and double test specimen methods with several products has indicated that it is of paramount importance that the specimen supports be ver

45、y rigid. With the double test specimen arrangement, the fixed supports should be maintained in parallel vertical planes. Both the arrangements shown in Figure 2 have proved suitable. 2 ISO 2012 All rights reserved ISO 16537:2012(E) 5.3 Adhesive The adhesive used to fix the test specimen shall be suc

46、h that the shear strength and modulus of the adhesive film is greater than that of the product under test. This ensures that rupture occurs in the test specimen rather than in the adhesive. Information on suitable adhesives and their use may be provided in the relevant product standard or any other

47、technical specification. Dimensions in millimetres Key 1 fixed machine grip 2 universal joint connection pins 3 tongue and groove 4 nut and bolt supports 5 adaptor 6 test specimen supports (length 330 mm, width 50 mm, thickness 16 mm) 7 test specimen (length 250 mm, width 50 mm) 8 load distribution

48、plates 9 movable machine grip Figure 1 Example of single specimen test assembly ISO 2012 All rights reserved 3 ISO 16537:2012(E) a) Key 1 loading plate (length 300 mm, width 100 mm, thickness 16 mm) 2 test specimen (length 200 mm, width 100 mm) 3 adhesive 4 metal test specimen supports (length 300 m

49、m, width 100 mm, thickness 16 mm) 4 ISO 2012 All rights reserved ISO 16537:2012(E) b) Key 1 loading plate 2 test specimen (length 200 mm, width 100 mm) 3 adhesive 4 metal test specimen supports 5 plywood test specimen supports Figure 2 Examples of double specimen test assemblies 6 Test specimens 6.1 Dimensions of test specimens 6.1.1 General The thickness of the test specimens shall be the original product thickness. Any moulded skins, facings and/or coating