ISO 16536-2012 Thermal insulating products for building applications - Determination of long-term water absorption by diffusion《建筑应用件用建筑物保温制品 通过扩散方式的长期吸水率测定》.pdf

《ISO 16536-2012 Thermal insulating products for building applications - Determination of long-term water absorption by diffusion《建筑应用件用建筑物保温制品 通过扩散方式的长期吸水率测定》.pdf》由会员分享，可在线阅读，更多相关《ISO 16536-2012 Thermal insulating products for building applications - Determination of long-term water absorption by diffusion《建筑应用件用建筑物保温制品 通过扩散方式的长期吸水率测定》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、 ISO 2012 Thermal insulating products for building applications Determination of long- term water absorption by diffusion Produits isolants thermiques destins aux applications du btiment Dtermination de labsorption deau long terme par diffusion INTERNATIONAL STANDARD ISO 16536 First edition 2012-05-

2、15 Reference number ISO 16536:2012(E) ISO 16536:2012(E) ii ISO 2012 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2012 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including ph

3、otocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in S

4、witzerland ISO 16536:2012(E) ISO 2012 All rights reserved iii Contents Page Foreword iv Introduction v 1 Scope 1 2 Normative references . 1 3 Principle . 1 4 Apparatus 1 5 Test specimens 2 5.1 Dimensions of test specimens 2 5.2 Number of test specimens 2 5.3 Preparation of test specimens . 3 5.4 Con

5、ditioning of test specimens 3 6 Procedure 3 6.1 Test procedure . 3 6.2 Test conditions . 3 7 Calculation and expression of results . 3 8 Accuracy of measurement 4 9 Test report . 4 ISO 16536:2012(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of nation

6、al standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. Internatio

7、nal organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rule

8、s given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at l

9、east 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 16536 was prepared by Technical Committee ISO/TC 1

10、63, Thermal performance and energy use in the built environment, Subcommittee SC 1, Test and measurement methods. ISO 16536 includes the original EN 12088 prepared by Technical Committee CEN/TC 88 “Thermal insulating materials and products”, with the following clauses modified to reflect the conditi

11、ons for tropical countries: Clause 5.4: Conditioning of test specimens; Clause 6.2: Test conditions; Clause 9: Test report. iv ISO 2012 All rights reserved ISO 16536:2012(E) Introduction ISO 16536 is one of a series of existing European Standards on test methods which were adopted by ISO. This group

12、 of International Standards comprises the following group of interrelated standards: ISO Title Respective EN standard 12344 Thermal insulating products for building applications Determination of bending behaviour EN 12089 12968 Thermal insulation products for building applications Determination of t

13、he pull-off resistance of external thermal insulation composite systems (ETICS) (foam block test) EN 13495 29465 Thermal insulating products for building applications Determination of length and width EN 822 29466 Thermal insulating products for building applications Determination of thickness EN 82

14、3 29467 Thermal insulating products for building applications Determination of squareness EN 824 29468 Thermal insulating products for building applications Determination of flatness EN 825 29469 Thermal insulating products for building applications Determination of compression behaviour EN 826 2947

15、0 Thermal insulating products for building applications Determination of the apparent density EN 1602 29471 Thermal insulating products for building applications Determination of dimensional stability under constant normal laboratory conditions (23 degrees C/50 % relative humidity) EN 1603 29472 The

16、rmal insulating products for building applications Determination of dimensional stability under specified temperature and humidity conditions EN 1604 29764 Thermal insulating products for building applications Determination of deformation under specified compressive load and temperature conditions E

17、N 1605 29765 Thermal insulating products for building applications Determination of tensile strength perpendicular to faces EN 1607 29766 Thermal insulating products for building applications Determination of tensile strength parallel to faces EN 1608 29767 Thermal insulating products for building a

18、pplications Determination of short- term water absorption by partial immersion EN 1609 29768 Thermal insulating products for building applications Determination of linear dimensions of test specimens EN 12085 29769 Thermal insulating products for building applications Determination of behaviour unde

19、r point load EN 12430 29770 Thermal insulating products for building applications Determination of thickness for floating-floor insulating products EN 12431 ISO 2012 All rights reserved v ISO 16536:2012(E) 29771 Thermal insulating materials for building applications Determination of organic content

20、EN 13820 29803 Thermal insulation products for building applications Determination of the resistance to impact of external thermal insulation composite systems (ETICS) EN 13497 29804 Thermal insulation products for building applications Determination of the tensile bond strength of the adhesive and

21、of the base coat to the thermal insulation material EN 13494 29805 Thermal insulation products for building applications Determination of the mechanical properties of glass fibre meshes EN 13496 16534 Thermal insulating products for building applications Determination of compressive creep EN 1606 16

22、535 Thermal insulating products for building applications Determination of long- term water absorption by immersion EN 12087 16536 Thermal insulating products for building applications Determination of long- term water absorption by diffusion EN 12088 16537 Thermal insulating products for building a

23、pplications Determination of shear behaviour EN 12090 16546 Thermal insulating products for building applications Determination of freeze- thaw resistance EN 12091 16544 Thermal insulating products for building applications Conditioning to moisture equilibrium under specified temperature and humidit

24、y conditions EN 12429 16545 Thermal insulating products for building applications Determination of behaviour under cyclic loading EN 13793 A further group of existing European Standards on test methods for products used to insulate building equipment and industrial installations comprises the follow

25、ing group of interrelated International Standards: ISO 12623 Thermal insulating products for building equipment and industrial installations Determination of short-term water absorption by partial immersion of preformed pipe insulation EN 13472 ISO 12624 Thermal insulating products for building equi

26、pment and industrial installations Determination of trace quantities of water soluble chloride, fluoride, silicate, sodium ions and pH EN 13468 ISO 12628 Thermal insulating products for building equipment and industrial installations Determination of dimensions, squareness and linearity of preformed

27、 pipe insulation EN 13467 ISO 12629 Thermal insulating products for building equipment and industrial installations Determination of water vapour transmission properties of preformed pipe insulation EN 13469 vi ISO 2012 All rights reserved INTERNATIONAL STANDARD ISO 16536:2012(E) Thermal insulating

28、products for building applications Determination of long-term water absorption by diffusion 1 Scope This International Standard specifies the equipment and procedures for determining the long-term water absorption of test specimens by diffusion. It is applicable to thermal insulating products. The t

29、est is intended to simulate the water absorption of products subjected to high relative humidities, approximating to 100 %, on both sides and subjected to a water vapour pressure gradient for a long period of time, e.g. inverted roof or unprotected ground insulation. The test is not applicable for a

30、ll types of thermal insulating products. The product standard should state for which of its products, if any, this test is applicable. NOTE For unprotected ground insulation, the temperature of 50 C may be replaced by a lower temperature, when more data are available. 2 Normative references The foll

31、owing referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 29768, Thermal insulating products for building appli

32、cations Determination of linear dimensions of test specimens 3 Principle The long-term water absorption by diffusion is determined by measuring the increase in the mass of a test specimen subjected to a water vapour pressure difference and temperature gradient for a period of 28 days. 4 Apparatus 4.

33、1 Balance, allows the determination of the mass of a test specimen to 0,1 g. 4.2 Corrosion-resistant container, a frame supporting the test specimens. 4.3 Heating device, a thermostat which provides water temperature control to (50 1) C. 4.4 Cooling plate, thermally insulated on the outside, operati

34、ng at a temperature of (1 0,5) C. 4.5 Tap water, adjusted to a temperature of (50 1) C. The principle of the apparatus assembly is illustrated in Figure 1. ISO 2012 All rights reserved 1 ISO 16536:2012(E) Dimensions in millimetres Key 1 cooling plate 2 thermal insulation of the cooling plate and the

35、 container 3 cooling medium inlet and outlet 4 test specimen 5 corrosion-resistant container with a frame supporting the test specimen 6 tap water 7 heating device with a thermostat 8 sealing Figure 1 Example of test device for water absorption by diffusion 5 Test specimens 5.1 Dimensions of test sp

36、ecimens The thickness of the test specimens shall be the original product thickness. The test specimens shall be squares with squarely cut edges having sides of (500 1) mm. If the product is not large enough to permit this size of test specimen, the test specimen size shall be reduced accordingly. T

37、est specimens shall contain no joints. 5.2 Number of test specimens The number of test specimens shall be at least two. 2 ISO 2012 All rights reserved ISO 16536:2012(E) 5.3 Preparation of test specimens The test specimens shall be cut so that they do not include original product edges. Test specimen

38、s shall be prepared by methods that do not substantially change the original structure of the product. Any facings, skins and/or coatings shall be retained. NOTE Special methods of preparation, when needed, are given in the relevant product standard or any other technical specification. 5.4 Conditio

39、ning of test specimens The test specimens shall be stored for at least 6 h at (23 5) C. In case of dispute they shall be stored at (23 2) C and (50 5) % relative humidity (RH) for the time stated in the relevant product standard with a minimum of 6 h. In tropical countries, different conditioning an

40、d testing conditions can be relevant. In this case, the conditions shall be (27 5) C and (65 5) % RH, and be stated clearly in the test report. 6 Procedure 6.1 Test procedure The dimensions of the test specimens shall be measured in accordance with ISO 29768. Weigh the test specimen to the nearest 0

41、,1 g to determine its initial mass, m 0 . Place the test specimen on the frame of the container. If the product is faced on one side, begin the test with it facing upwards. Seal the bottom edge of the test specimen to the container. The width of the sealing shall be 10 mm (see Figure 1). Place the i

42、nsulated cooling plate on top of the test specimen. Subject the test specimen to a temperature and a water vapour pressure difference for 28 days by maintaining the water at a temperature of (50 1) C and the cooling on the other side at a temperature of (1 0,5) C. Turn the test specimen over every 7

43、 days. After 28 days, remove the test specimen and wipe off any surface water. Weigh the test specimen again to determine its mass, m D . 6.2 Test conditions The test shall be carried out at (23 2) C and (50 5) % RH. NOTE Other conditions may be given in the relevant product standard or can be agree

44、d between parties. In tropical countries, different conditioning and testing conditions can be relevant. In this case, the conditions shall be (27 2) C and (65 5) % RH. 7 Calculation and expression of results The test result, W dpor W dV , shall be the mean value of the individual values. Results sh

45、all not be extrapolated to other thicknesses. Calculate the long-term water absorption by diffusion for each test specimen, W dpor W dV , in kilogrammes per square metre or volume percent using Equation (1) or (2): W mm A dp D p 0 1 (1) ISO 2012 All rights reserved 3 ISO 16536:2012(E) W mm Ad dV D p

46、W 0 100 (2) where m 0is the initial mass of the test specimen, in kg; m Dis the mass of the test specimen after submission to water absorption by diffusion for 28 days, in kg; A pis the bottom surface area of the test specimen, in m 2 ; d is the thickness of the test specimen, in m; Wis the density

47、of water, assumed to be 1000 kg/m 3 . W dpshall be rounded to the nearest 0,01 kg/m 2 . W dVshall be rounded to the nearest 0,1 volume percent. 8 Accuracy of measurement NOTE It has not been possible to include a statement on the accuracy of measurement in this edition of this International Standard

48、, but it is intended to include such a statement when this International Standard is next revised. 9 Test report The test report shall include the following information: a) reference to this International Standard, i.e. ISO 16536:2012; b) product identification 1) product name, factory, manufacturer

49、 or supplier; 2) production code number; 3) type of product; 4) packaging; 5) the form in which the product arrived at the laboratory; 6) other information as appropriate, e.g. nominal thickness, nominal density; c) test procedure 1) pre-test history and sampling, e.g. who sampled and where; 2) conditioning; 3) if any deviation from Clauses 6 and 7; 4) date of testing; 5) conditioning in tropical countries, if applicabl