IEEE SI 10-2010 en American National Standard for Metric Practice《公制实施规程的美国国家标准》.pdf

《IEEE SI 10-2010 en American National Standard for Metric Practice《公制实施规程的美国国家标准》.pdf》由会员分享，可在线阅读，更多相关《IEEE SI 10-2010 en American National Standard for Metric Practice《公制实施规程的美国国家标准》.pdf（78页珍藏版）》请在麦多课文档分享上搜索。

1、g3g3g3g3g3g3g3g3g3g3g3g3g3g3g3American National Standard forMetric Practice g3Co-SponsorsASTM Committee E43 on SI Practice andIEEE Standards Coordinating Committee 14 (Quantities, Units, and Letter Symbols) IEEE 3 Park Avenue New York, NY 10016-5997 USA11 April 2011 IEEE/ASTM SI 10-2010g3g3g3g3g3g3g

2、3g3g3g3g3g3g3g3g3g3g3g3g3g3g3g3g3g3g3g3g3g3g3g3g3g3g3g3g3g3g3g3g3(Revisiong3ofg3g3g3g3g3g3g3g3g3g3g3g3g3g3g3IEEE/ASTMg3SIg310g4862002)Recognized as an IEEE/ASTM SI 10TM-2010 American National Standard (ANSI) (Revision of IEEE/ASTM SI 10-2002) American National Standard for Metric Practice Co-Sponsor

3、s ASTM Committee E43 on SI Practice and IEEE Standards Coordinating Committee 14 (Quantities, Units, and Letter Symbols) Approved 8 December 2010 IEEE-SA Standards Board Approved 1 March 2011 ASTM International Approved 1 March 2011 American National Standards Institute Abstract: Guidance for the us

4、e of the modern metric system is given. Known as the International System of Units (abbreviated SI), the system is the basis for worldwide standardization of measurement units. Information is included on SI, a list of units recognized for use with SI, and a list of conversion factors, together with

5、general guidance on proper style and usage. Keywords: conversion factors, International System, International System of Units, metric practice, metric system, rounding, SI, SI 10, Systme International dUnits The Institute of Electrical and Electronics Engineers, Inc. 3 Park Avenue, New York, NY 1001

6、6-5997, USA ASTM International 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, USA Copyright 2011 by the Institute of Electrical and Electronics Engineers, Inc. and ASTM International All rights reserved. Published 11 April 2011. Printed in the United States of America. SECON

7、D PRINTING: 14 October 2013: Correction made to Table A.1, page 30 ounce (troy or apothecary) (oz) row. IEEE is a registered trademark in the U.S. Patent +1 978 750 8400. Permission to photocopy portions of any individual standard for educational classroom use can also be obtained through the Copyri

8、ght Clearance Center. ASTM International is a global forum for the development of consensus standards. For over a century, industries around the world have turned to ASTM International for the development of voluntary consensus standards. Known for their high technical quality and market relevance,

9、these standards are an important part of the information infrastructure that guides design, manufacturing, and trade in the global economy.Organized in 1898, ASTM International is one of the largest voluntary standards developing organizations in the world. ASTM provides the forum for the developmen

10、t and publication of voluntary consensus standards for materials, products, systems, and services. ASTMs members, representing producers, users, consumers, government, and academia from over 100 countries, develop technical documents that are the basis for manufacturing, management, procurement, cod

11、es, and regulations. ASTM members belong to one or more committees, each of which covers a subject area such as steel, petroleum, medical devices, property management, consumer products, and many more. It is these committees that develop the more than 11 000 ASTM standards that can be found on ASTMs

12、 website: www.astm.org and in the 77-volume Annual Book of ASTM Standards (available in print and on CD Rom). Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. Your comments will receive careful cons

13、ideration at a meeting of the responsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards at the address shown below.For more information on this standard and other ASTM pub

14、lications, contact: ASTM International 100 Barr Harbor Drive P.O. Box C700 West Conshohocken, PA 19428-2959 USA Phone: + 1 610 832-9500 Fax: + 1 610 832-9555 e-mail: serviceastm.org web: www.astm.org American National Standard An American National Standard implies a consensus of those substantially

15、concerned with its scope and provisions. An American National Standard is intended as a guide to aid the manufacturer, the consumer, and the general public. The existence of an American National Standard does not in any respect preclude anyone, whether he has approved the standard or not, from manuf

16、acturing, marketing, purchasing, or using products, processes, or procedures not conforming to the standard. American National Standards are subject to periodic review and users are cautioned to obtain the latest editions. CAUTION NOTICE: This American National Standard may be revised or withdrawn a

17、t any time. The procedures of the American National Standards Institute require that action be taken to reaffirm, revise, or withdraw this standard no later than five years from the date of publication. Purchasers of American National Standards may receive current information on all standards by cal

18、ling or writing the American National Standards Institute. Authorization to photocopy portions of any individual standard for internal or personal use is granted by the Institute of Electrical and Electronics Engineers, Inc., provided that the appropriate fee is paid to Copyright Clearance Center. T

19、o arrange for payment of licensing fee, please contact Copyright Clearance Center, Customer Service, 222 Rosewood Drive, Danvers, MA 01923 USA; (978) 750-8400. Permission to photocopy portions of any individual standard for educational classroom use can also be obtained through the Copyright Clearan

20、ce Center. vi Copyright 2011 IEEE/ASTM. All rights reserved. IntroductionThis introduction is not part of IEEE/ASTM SI10-2011, American National Standard for Metric Practice. This document, which supersedes IEEE/ASTM SI10-2002, is the primary American National Standard for use of the International S

21、ystem of Units (SI). The first version of this standard that was published jointly by the IEEE and ASTM appeared in 1976. The sponsoring societies welcome comments and suggestions from interested individuals and organizations. In 1988, the Metric Conversion Act was amended to designate “the metric s

22、ystem of measurement as the preferred system of weights and measures for United States trade and commerce.” With the increasing importance of the global marketplace, it has become imperative for U.S. industry to extend its use of SI and for U.S. citizens to gain a working knowledge of this modern me

23、tric system. This standard is intended to give authoritative information on SI and appropriate guidance concerning its application. SI is defined in the document Le Systme International dUnits, published in French, with an English translation, by the International Bureau of Weights and Measures (BIP

24、M). The BIPM was set up by the Convention du Mtre, signed in 1875 (see Annex D). Le Systme International dUnits, known informally as the “BIPM SI Brochure,” is revised from time to time in accordance with the decisions of the General Conference on Weights and Measures (CGPM) and other international

25、organizations. A U.S. version is published by NIST B22.aThis standard is consistent with the SI brochure in all matters that concern the SI itself, except that it presents the degree Celsius as simply another name for the kelvin that is used to express Celsius temperature, while the BIPM SI Brochure

26、 lists the degree Celsius as an SI derived unit. Of more practical importance is the difference in approach to non-SI units. IEEE/ASTM SI10 and its predecessors have traditionally been more restrictive in their recommendations concerning the use of non-SI units. The SI Brochure, for example, lists t

27、he ngstrm as a unit that is “currently accepted for use with the International System” and lists the centimeter-gram-second (CGS) units and many others as units whose use “is not encouraged.” IEEE/ASTM SI10, which is intended for the United States and developed under the consensus standardization pr

28、ocess, makes the significantly stronger recommendation that these units are “not to be used.” Notice to users Laws and regulations Users of these documents should consult all applicable laws and regulations. Compliance with the provisions of this standard does not imply compliance to any applicable

29、regulatory requirements. Implementers of the standard are responsible for observing or referring to the applicable regulatory requirements. IEEE does not, by the publication of its standards, intend to urge action that is not in compliance with applicable laws, and these documents may not be constru

30、ed as doing so. Copyrights This document is copyrighted by the IEEE and ASTM. It is made available for a wide variety of both public and private uses. These include both use, by reference, in laws and regulations, and use in private aThe numbers in brackets correspond to those of the bibliography in

31、 Annex E.vii Copyright 2011 IEEE/ASTM. All rights reserved. regulation, standardization, and the promotion of engineering practices and methods. By making this document available for use and adoption by public authorities and private users, the IEEE does not waive any rights in copyright to this doc

32、ument. Updating of IEEE documents Users of IEEE standards should be aware that these documents may be superseded at any time by the issuance of new editions or may be amended from time to time through the issuance of amendments, corrigenda, or errata. An official IEEE document at any point in time c

33、onsists of the current edition of the document together with any amendments, corrigenda, or errata then in effect. In order to determine whether a given document is the current edition and whether it has been amended through the issuance of amendments, corrigenda, or errata, visit the IEEE Standards

34、 Association web site at http:/ieeexplore.ieee.org/xpl/standards.jsp, or contact the IEEE at the address listed previously. For more information about the IEEE Standards Association or the IEEE standards development process, visit the IEEE-SA web site at http:/standards.ieee.org. Errata Errata, if a

35、ny, for this and all other standards can be accessed at the following URL: http:/standards.ieee.org/reading/ieee/updates/errata/index.html. Users are encouraged to check this URL for errata periodically. Interpretations Current interpretations can be accessed at the following URL: http:/standards.ie

36、ee.org/reading/ieee/interp/ index.html. Patents Attention is called to the possibility that implementation of this standard may require use of subject matter covered by patent rights. By publication of this standard, no position is taken with respect to the existence or validity of any patent rights

37、 in connection therewith. The IEEE is not responsible for identifying Essential Patent Claims for which a license may be required, for conducting inquiries into the legal validity or scope of Patents Claims or determining whether any licensing terms or conditions provided in connection with submissi

38、on of a Letter of Assurance, if any, or in any licensing agreements are reasonable or non-discriminatory. Users of this standard are expressly advised that determination of the validity of any patent rights, and the risk of infringement of such rights, is entirely their own responsibility. Further i

39、nformation may be obtained from the IEEE Standards Association. viii Copyright 2011 IEEE/ASTM. All rights reserved. Participants This standard was developed by the IEEE/ASTM Committee for Maintaining IEEE/ASTM SI 10, a joint committee established by the sponsoring organizations. The proposed standar

40、d generated by this joint committee was then formally adopted by the IEEE and ASTM before transmission to the American National Standards Institute for approval as an American National Standard. At the time of the approval of this revision, the joint committee had the following membership. Nonvoting

41、 members at the time of publication are marked with an asterisk (*): Bruce Barrow, Chair James R. Frysinger, Vice Chair Robert H. Bushnell, Secretary Nancy Bale Dennis Brownridge* Rodney Conn* Anthony French Uri Gat Stan Jakuba Bill Potts Howard Ressel* John T. Scott Ralph Showers* Barry N. Taylor*

42、Ambler Thompson Paul Trusten* Gerry Uttrachi* Matthew Zotter* ix Copyright 2011 IEEE/ASTM. All rights reserved. Contents 1. Overview 1 1.1 Scope . 1 1.2 Introduction 1 2. SI units and symbols . 2 2.1 Classes of units 2 2.2 SI prefixes 6 3. Use of the SI . 7 3.1 General . 7 3.2 Application of SI pref

43、ixes 7 3.3 Other units . 9 3.4 Some comments concerning quantities and units 13 3.5 Style and usage 16 Annex A (informative) Tables of conversion factors . 20 Annex B (informative) Rules for conversion and rounding . 44 Annex C (informative) Comments concerning the application of the International S

44、ystem of Units (SI) 50 Annex D (informative) Development of the International System of Units (SI) 55 Annex E (informative) Bibliography 58 Index . 60 1 Copyright 2011 IEEE/ASTM. All rights reserved. American National Standard for Metric Practice IMPORTANT NOTICE: This standard is not intended to en

45、sure safety, security, health, or environmental protection. Implementers of the standard are responsible for determining appropriate safety, security, environmental, and health practices or regulatory requirements. This IEEE document is made available for use subject to important notices and legal d

46、isclaimers. These notices and disclaimers appear in all publications containing this document and may be found under the heading “Important Notice” or “Important Notices and Disclaimers Concerning IEEE Documents.” They can also be obtained on request from IEEE or viewed at http:/standards.ieee.org/I

47、PR/disclaimers.html. 1. Overview 1.1 Scope This document is the primary American National Standard on application of the metric system. It emphasizes use of the International System of Units (SI), which is the modern, internationally accepted metric system. It includes information on SI, a limited l

48、ist of units recognized for use with SI, and a list of conversion factors, together with general guidance on style and usage. It also lists older “metric” units that shall no longer be used. The word “primary” implies that other metric standards in the United States should be consistent with this do

49、cument. 1.2 Introduction Any measurable physical quantity can be represented in the SI with the aid of just seven “base units”the units for the quantities length, mass, time, electric current, temperature, amount of substance, and luminous intensityor by combinations (called “derived units”) of these seven. For example, the unit of speed can be expressed by the unit of length divided by the unit of time. This standard shows first the two classes of units (base and derived) that make up the SI, together with the standard symbols that may be used to rep