IEEE 1815 1-2015 en Exchanging Information Between Networks Implementing IEC 61850 and IEEE Std 1815 [Distributed Network Protocol (DNP3)] (Incorporates Corrige.pdf

《IEEE 1815 1-2015 en Exchanging Information Between Networks Implementing IEC 61850 and IEEE Std 1815 [Distributed Network Protocol (DNP3)] (Incorporates Corrige.pdf》由会员分享，可在线阅读，更多相关《IEEE 1815 1-2015 en Exchanging Information Between Networks Implementing IEC 61850 and IEEE Std 1815 [Distributed Network Protocol (DNP3)] (Incorporates Corrige.pdf（358页珍藏版）》请在麦多课文档分享上搜索。

1、 IEEE Standard for Exchanging Information Between Networks Implementing IEC 61850 and IEEE Std 1815 Distributed Network Protocol (DNP3) Sponsored by the Substations Committee IEEE 3 Park Avenue New York, NY 10016-5997 USA IEEE Power and Energy Society IEEE Std 1815.1-2015 (Incorporates IEEE Std 1815

2、.1-2015/Cor 1-2016) IEEE Std 1815.1-2015 (Incorporates IEEE Std 1815.1-2015/Cor 1-2016) IEEE Standard for Exchanging Information Between Networks Implementing IEC 61850 and IEEE Std 1815 Distributed Network Protocol (DNP3) Sponsor Substations Committee of the IEEE Power and Energy Society Approved 5

3、 December 2015 IEEE-SA Standards Board Acknowledgments The IEEE Substations Working Group (IEEE WG C14) gratefully acknowledges important contributions and assistance in the development of this standard from the following: H. Lee Smith, who was the past Chair of WG C14 and who passed away in 2015. N

4、ational Institute of Standards and Technology (NIST). Smart Grid Interoperability Panel (SGIP). DNP User Group. Electric Power Research Institute (EPRI). IEEE WG C14 thanks the International Electrotechnical Commission (IEC) for permission to reproduce information from its International Publication

5、IEC 61850-7-2 ed.2.0 (2010), IEC 61850-7-3 ed.2.0 (2010), and IEC 61850-80-1 ed.1.0 (2008). All such extracts are copyright of IEC, Geneva, Switzerland. All rights reserved. Further information on the IEC is available from www.iec.ch. IEC has no responsibility for the placement and context in which

6、the extracts and contents are reproduced by the author, nor is IEC in any way responsible for the other content or accuracy therein. Abstract: This document specifies the standard approach for mapping between IEEE Std 1815 Distributed Network Protocol (DNP3) and IEC 61850 (Communications Networks an

7、d Systems for Power Utility Automation). Two primary use cases are addressed: a) mapping between an IEEE 1815-based master and an IEC 61850-based remote site and b) mapping between an IEC 61850-based master and an IEEE 1815-based remote site. Mapping aspects included in the standard are: conceptual

8、architecture; general mapping requirements; the mapping of Common Data Classes, Constructed Attribute Classes and Abstract Communication Service Interface (ACSI); cyber security requirements, the architecture of a gateway used for translation and requirements for embedding mapping configuration info

9、rmation into IEC 61850 System Configuration Description Language (SCL) and DNP3 Device Profile. This standard addresses a selection of features, data classes, and services of the two standards. Keywords: automation, communications, DNP3, evolution, feeder, gateway, IEC 61850, IEEE 1815, mapping, net

10、work, power system, substation, upgrade, utility The Institute of Electrical and Electronics Engineers, Inc. 3 Park Avenue, New York, NY 10016-5997, USA Copyright 2016 by The Institute of Electrical and Electronics Engineers, Inc. All rights reserved. Published 16 December 2016. Printed in the Unite

11、d States of America. IEEE is a registered trademark in the U.S. Patent fitness for a particular purpose; non-infringement; and quality, accuracy, effectiveness, currency, or completeness of material. In addition, IEEE disclaims any and all conditions relating to: results; and workmanlike effort. IEE

12、E standards documents are supplied “AS IS” and “WITH ALL FAULTS.” Use of an IEEE standard is wholly voluntary. The existence of an IEEE standard does not imply that there are no other ways to produce, test, measure, purchase, market, or provide other goods and services related to the scope of the IE

13、EE standard. Furthermore, the viewpoint expressed at the time a standard is approved and issued is subject to change brought about through developments in the state of the art and comments received from users of the standard. In publishing and making its standards available, IEEE is not suggesting o

14、r rendering professional or other services for, or on behalf of, any person or entity nor is IEEE undertaking to perform any duty owed by any other person or entity to another. Any person utilizing any IEEE Standards document, should rely upon his or her own independent judgment in the exercise of r

15、easonable care in any given circumstances or, as appropriate, seek the advice of a competent professional in determining the appropriateness of a given IEEE standard. IN NO EVENT SHALL IEEE BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT N

16、OT LIMITED TO: PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE PUBLICATION, USE OF, OR

17、 RELIANCE UPON ANY STANDARD, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE AND REGARDLESS OF WHETHER SUCH DAMAGE WAS FORESEEABLE. Translations The IEEE consensus development process involves the review of documents in English only. In the event that an IEEE standard is translated, only the Engli

18、sh version published by IEEE should be considered the approved IEEE standard. Official statements A statement, written or oral, that is not processed in accordance with the IEEE-SA Standards Board Operations Manual shall not be considered or inferred to be the official position of IEEE or any of its

19、 committees and shall not be considered to be, or be relied upon as, a formal position of IEEE. At lectures, symposia, seminars, or educational courses, an individual presenting information on IEEE standards shall make it clear that his or her views should be considered the personal views of that in

20、dividual rather than the formal position of IEEE. Comments on standards Comments for revision of IEEE Standards documents are welcome from any interested party, regardless of membership affiliation with IEEE. However, IEEE does not provide consulting information or advice pertaining to IEEE Standard

21、s documents. Suggestions for changes in documents should be in the form of a proposed change of text, together with appropriate supporting comments. Since IEEE standards represent a consensus of concerned interests, it is important that any responses to comments and questions also receive the concur

22、rence of a balance of interests. For this reason, IEEE and the members of its societies and Standards Coordinating Committees are not able to provide an instant response to comments or questions except in those cases where the matter has previously been addressed. For the same reason, IEEE does not

23、respond to interpretation requests. Any person who would like to participate in revisions to an IEEE standard is welcome to join the relevant IEEE working group. Comments on standards should be submitted to the following address: Secretary, IEEE-SA Standards Board 445 Hoes Lane Piscataway, NJ 08854

24、USA Laws and regulations Users of IEEE Standards documents should consult all applicable laws and regulations. Compliance with the provisions of any IEEE Standards document does not imply compliance to any applicable regulatory requirements. Implementers of the standard are responsible for observing

25、 or referring to the applicable regulatory requirements. IEEE does not, by the publication of its standards, intend to urge action that is not in compliance with applicable laws, and these documents may not be construed as doing so. Copyrights IEEE draft and approved standards are copyrighted by IEE

26、E under U.S. and international copyright laws. They are made available by IEEE and are adopted for a wide variety of both public and private uses. These include both use, by reference, in laws and regulations, and use in private self-regulation, standardization, and the promotion of engineering prac

27、tices and methods. By making these documents available for use and adoption by public authorities and private users, IEEE does not waive any rights in copyright to the documents. Photocopies Subject to payment of the appropriate fee, IEEE will grant users a limited, non-exclusive license to photocop

28、y portions of any individual standard for company or organizational internal use or individual, non-commercial use only. To arrange for payment of licensing fees, please contact Copyright Clearance Center, Customer Service, 222 Rosewood Drive, Danvers, MA 01923 USA; +1 978 750 8400. Permission to ph

29、otocopy portions of any individual standard for educational classroom use can also be obtained through the Copyright Clearance Center. Updating of IEEE Standards documents Users of IEEE Standards documents should be aware that these documents may be superseded at any time by the issuance of new edit

30、ions or may be amended from time to time through the issuance of amendments, corrigenda, or errata. An official IEEE document at any point in time consists of the current edition of the document together with any amendments, corrigenda, or errata then in effect. Every IEEE standard is subjected to r

31、eview at least every ten years. When a document is more than ten years old and has not undergone a revision process, it is reasonable to conclude that its contents, although still of some value, do not wholly reflect the present state of the art. Users are cautioned to check to determine that they h

32、ave the latest edition of any IEEE standard. In order to determine whether a given document is the current edition and whether it has been amended through the issuance of amendments, corrigenda, or errata, visit the IEEE Xplore at http:/ieeexplore.ieee.org/ or contact IEEE at the address listed prev

33、iously. For more information about the IEEE-SA or IEEEs standards development process, visit the IEEE-SA Website at http:/standards.ieee.org. Errata Errata, if any, for all IEEE standards can be accessed on the IEEE-SA Website at the following URL: http:/standards.ieee.org/findstds/errata/index.html

34、. Users are encouraged to check this URL for errata periodically. Patents Attention is called to the possibility that implementation of this standard may require use of subject matter covered by patent rights. By publication of this standard, no position is taken by the IEEE with respect to the exis

35、tence or validity of any patent rights in connection therewith. If a patent holder or patent applicant has filed a statement of assurance via an Accepted Letter of Assurance, then the statement is listed on the IEEE-SA Website at http:/standards.ieee.org/about/sasb/patcom/patents.html. Letters of As

36、surance may indicate whether the Submitter is willing or unwilling to grant licenses under patent rights without compensation or under reasonable rates, with reasonable terms and conditions that are demonstrably free of any unfair discrimination to applicants desiring to obtain such licenses. Essent

37、ial Patent Claims may exist for which a Letter of Assurance has not been received. The IEEE is not responsible for identifying Essential Patent Claims for which a license may be required, for conducting inquiries into the legal validity or scope of Patents Claims, or determining whether any licensin

38、g terms or conditions provided in connection with submission of a Letter of Assurance, if any, or in any licensing agreements are reasonable or non-discriminatory. Users of this standard are expressly advised that determination of the validity of any patent rights, and the risk of infringement of su

39、ch rights, is entirely their own responsibility. Further information may be obtained from the IEEE Standards Association. Participants At the time this IEEE standard was completed, the Substations Working Group had the following membership: Ronald Farquharson, Chair Grant Gilchrist, Working Group Ed

40、itor Ed Cenzon, Secretary William Ackerman Christoph Brunner Panitarn (Joseph) Chongfuangprinya Mason Clark Jim Coats Lorene Cunningham Mike Dood Kevin Easley Derek R. Flickinger David Goughnour Yi Hu Randy D. Kimura Ronald Landheer-Cieslak Gregory Luri Parker McCauley Rick Murphy Bruce Muschlitz Pa

41、ul Myrda Rodolfo Pellizzoni Bogdan Popescu Craig M. Preuss Grant Ringham Sam Sciacca H. Lee Smith Michael S. Smith Marcus Steel John T. Tengdin Eric Thibodeau Jay Vellore Vinoo S. Warrier Andrew West Deceased The following members of the individual balloting committee voted on this standard. Ballote

42、rs may have voted for approval, disapproval, or abstention. William Ackerman Mark Adamiak S. Aggarwal Ali Al Awazi Mihaela Albu Jay Anderson Galina Antonova Ficheux Arnaud James Baker John Banting Martin Baur Philip Beaumont Paul Bishop William Bloethe Christoph Brunner Paul Cardinal Keith Chow Fran

43、ces Cleveland Jim Coats Stephen Conrad Charles Cook Lorene Cunningham Alireza Daneshpooy Ratan Das Em Delahostria Michael Dood P. Eastman David Farmer Ronald Farquharson Keith Flowers Dan Friedman Grant Gilchrist Mietek Glinkowski Jalal Gohari Edwin Goodwin David Goughnour Roman Graf Stephen Grier R

44、andall Groves Erich Gunther Jeffrey Helzer Mariana Hentea Gary Heuston Werner Hoelzl Gary Hoffman Dennis Holstein Yi Hu C. Huntley Richard Jackson Innocent Kamwa Piotr Karocki John Kay Jeffrey Kester Yuri Khersonsky Morteza Khodaie Stanley Klein J. Koepfinger Mieczyslaw Kokar Bruce Kraemer Jim Kulch

45、isky Marc Lacroix Chung-Yiu Lam Jeremy Landt Federico Lopez Greg Luri Elvis Maculuba Kenneth Martin Pierre Martin Edward McCall John McDonald Hank McGlynn Michael Meisinger Jeffery Mizener Jose Morales Adi Mulawarman R. Murphy Bruce Muschlitz Paul Myrda Pratap Mysore Arthur Neubauer Michael Newman G

46、ary Nissen Yoshihiro Ohba Lorraine Padden Donald Parker Bansi Patel Bogdan Popescu Craig Preuss Farnoosh Rahmatian John Randolph Grant Ringham Michael Roberts Charles Rogers Copyright 2016 IEEE. All rights reserved. vii Oleg Roizman Benjamin Rolfe William Rose Bob Saint Steven Sano Sergio Santos Bar

47、tien Sayogo Thomas Schossig Samuel Sciacca Devki Sharma Yasuro Shobatake Gil Shultz Cheong Siew Mark Simon Herbert Sinnock Jerry Smith Michael Smith John Spare Thomas Starai Marcus Steel Scott Sternfeld Gary Stoedter Ryan Stone Raymond Strittmatter Walter Struppler Charles Sufana William Taylor John

48、 Tengdin Eric Thibodeau Joe Uchiyama Eric Udren Luis Vargas John Vergis Jane Verner Ilia Voloh Daniel Ward Solveig Ward Joseph Weiss Andrew West Oren Yuen When the IEEE-SA Standards Board approved this standard on 5 December 2015, it had the following membership: John D. Kulick, Chair Jon Walter Ros

49、dahl, Vice Chair Richard H. Hulett, Past Chair Konstantinos Karachalios, Secretary Masayuki Ariyoshi Ted Burse Stephen Dukes Jean-Philippe Faure J. Travis Griffith Gary Hoffman Michael Janezic Joseph L. Keopfinger* David Law Hung Ling Andrew Myles T. W. Olsen Glenn Parsons Ronald C. Petersen Annette D. Reilly Stephen J. Shellhammer Adrian P. Stephens Yatin Trivedi Philip Winston Don Wright Yu Yuan Daidi Zhong *Member Emeritus Copyright 2016 IEEE. All rights reserved. viii Introduction This introduction is not part of IEEE Std 1815.1-2015, IEEE Standard for E