IEC 62841-3-10-2015 Electric motor-operated hand-held tools transportable tools and lawn and garden machinery - Safety - Part 3-10 Particular requirements for t.pdf

《IEC 62841-3-10-2015 Electric motor-operated hand-held tools transportable tools and lawn and garden machinery - Safety - Part 3-10 Particular requirements for t.pdf》由会员分享，可在线阅读，更多相关《IEC 62841-3-10-2015 Electric motor-operated hand-held tools transportable tools and lawn and garden machinery - Safety - Part 3-10 Particular requirements for t.pdf（32页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 62841-3-10 Edition 1.0 2015-09 INTERNATIONAL STANDARD Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery Safety Part 3-10: Particular requirements for transportable cut-off machines IEC 62841-3-10:2015-09(en) colour inside THIS PUBLICATION IS COPYRIGHT PR

2、OTECTED Copyright 2015 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IEC

3、s member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. IEC Central Offic

4、e Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic

5、and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. IEC Catalogue - webstore.iec.ch/catalogue The stand-alone ap

6、plication for consulting the entire bibliographical information on IEC International Standards, Technical Specifications, Technical Reports and other documents. Available for PC, Mac OS, Android Tablets and iPad. IEC publications search - www.iec.ch/searchpub The advanced search enables to find IEC

7、publications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new publication

8、s released. Available online and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 30 000 terms and definitions in English and French, with equivalent terms in 15 additional languages. Also kno

9、wn as the International Electrotechnical Vocabulary (IEV) online. IEC Glossary - std.iec.ch/glossary More than 60 000 electrotechnical terminology entries in English and French extracted from the Terms and Definitions clause of IEC publications issued since 2002. Some entries have been collected fro

10、m earlier publications of IEC TC 37, 77, 86 and CISPR. IEC Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Service Centre: csciec.ch. IEC 62841-3-10 Edition 1.0 2015-09 INTERNATIONAL STANDA

11、RD Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery Safety Part 3-10: Particular requirements for transportable cut-off machines INTERNATIONAL ELECTROTECHNICAL COMMISSION ICS 25.140.20 ISBN 978-2-8322-2912-5 Registered trademark of the International Electrot

12、echnical Commission Warning! Make sure that you obtained this publication from an authorized distributor. colour inside 2 IEC 62841-3-10:2015 IEC 2015 CONTENTS FOREWORD . 4 1 Scope 6 2 Normative references 6 3 Terms and definitions 6 4 General requirements 7 5 General conditions for the tests . 7 6

13、Radiation, toxicity and similar hazards . 8 7 Classification . 8 8 Marking and instructions 8 9 Protection against access to live parts . 11 10 Starting . 11 11 Input and current . 11 12 Heating 11 13 Resistance to heat and fire 11 14 Moisture resistance . 11 15 Resistance to rusting . 11 16 Overloa

14、d protection of transformers and associated circuits 11 17 Endurance . 11 18 Abnormal operation . 12 19 Mechanical hazards . 12 20 Mechanical strength 17 21 Construction 18 22 Internal wiring 18 23 Components 19 24 Supply connection and external flexible cords . 19 25 Terminals for external conducto

15、rs 19 26 Provision for earthing 19 27 Screws and connections 19 28 Creepage distances, clearances and distances through insulation . 19 Annexes . 26 Annex I (informative) Measurement of noise and vibration emissions . 26 Annex K (normative) Battery tools and battery packs . 27 Bibliography 28 Figure

16、 101 Example of a cut-off machine . 20 Figure 102 Examples of gaps and rake angles . 21 Figure 103 Wheel guards . 22 Figure 104 Test probe 22 Figure 105 Spark deflection . 23 Figure 106 Principal designs and dimensions of flanges 24 Figure 107 Position of test hole for impact test . 25 IEC 62841-3-1

17、0:2015 IEC 2015 3 Figure 108 Wheel guard material strength test . 25 Table 4 Required performance levels . 12 Table 101 Flange dimensions 16 Table 102 Torques for testing flanges 17 Table I.101 Noise test conditions for cut-off machines . 26 4 IEC 62841-3-10:2015 IEC 2015 INTERNATIONAL ELECTROTECHNI

18、CAL COMMISSION _ ELECTRIC MOTOR-OPERATED HAND-HELD TOOLS, TRANSPORTABLE TOOLS AND LAWN AND GARDEN MACHINERY SAFETY Part 3-10: Particular requirements for transportable cut-off machines FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization com

19、prising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Sta

20、ndards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this pre

21、paratory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two orga

22、nizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form

23、 of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretat

24、ion by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or reg

25、ional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out

26、 by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees

27、 for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the

28、Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held r

29、esponsible for identifying any or all such patent rights. International Standard IEC 62841-3-10 has been prepared by IEC technical committee 116: Safety of motor-operated electric tools. The text of this standard is based on the following documents: FDIS Report on voting 116/240/FDIS 116/253/RVD Ful

30、l information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. IEC 62841-3-10:2015 IEC 2015 5 This Part 3-10 is to be used in conjunction with the fi

31、rst edition of IEC 62841-1 (2014). This Part 3-10 supplements or modifies the corresponding clauses in IEC 62841-1, so as to convert it into the IEC Standard: Particular requirements for transportable cut-off machines. Where a particular subclause of Part 1 is not mentioned in this Part 3-10, that s

32、ubclause applies as far as relevant. Where this standard states “addition”, “modification” or “replacement”, the relevant text in Part 1 is to be adapted accordingly. The following print types are used: requirements: in roman type; test specifications: in italic type; notes: in small roman type. Wor

33、ds in bold in the text are defined in Clause 3. When a definition concerns an adjective, the adjective and the associated noun are also in bold. Subclauses, notes and figures which are additional to those in Part 1 are numbered starting from 101. A list of all parts of the IEC 62841 series, under th

34、e general title: Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery Safety, can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC website under “http

35、:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. A bilingual version of this publication may be issued at a later date. NOTE The attention of National Committees is drawn to th

36、e fact that equipment manufacturers and testing organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the rec

37、ommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication. IMPORTANT The colour inside logo on the cover page of this publication indicates that it contains colours which are considered to be use

38、ful for the correct understanding of its contents. Users should therefore print this document using a colour printer. 6 IEC 62841-3-10:2015 IEC 2015 ELECTRIC MOTOR-OPERATED HAND-HELD TOOLS, TRANSPORTABLE TOOLS AND LAWN AND GARDEN MACHINERY SAFETY Part 3-10: Particular requirements for transportable

39、cut-off machines 1 Scope This clause of Part 1 is applicable, except as follows: Addition: This part of IEC 62841 applies to transportable cut-off machines intended to cut materials such as metals, concrete and masonry and to be fitted with one abrasive bonded reinforced wheel of Type 41, or diamond

40、 cut-off wheel with the peripheral gaps, if any, not exceeding 10 mm and with a rated no-load speed not exceeding a peripheral speed of the wheel of 100 m/s with the maximum wheel diameter and a wheel diameter range of 250 mm to 410 mm. This standard does not apply to: transportable mitre saws; tran

41、sportable tile saws; transportable metal saws. NOTE 101 Transportable mitre saws are covered by IEC 62841-3-9. Transportable tile saws will be covered by a future part of IEC 62841-3. Transportable metal saws will be covered by a future part of IEC 62841-3. 2 Normative references This clause of Part

42、 1 is applicable except as follows: Addition: ISO 603-15, Bonded abrasive products Dimensions Part 15: Grinding wheels for cutting- off on stationary or mobile cutting-off machines ISO 630 (all parts), Structural steels 3 Terms and definitions This clause of Part 1 is applicable, except as follows:

43、3.101 inner flange part that contacts and provides support to the back side of the wheel and is located on the spindle between wheel and tool IEC 62841-3-10:2015 IEC 2015 7 3.102 bonded reinforced wheel wheel for different applications and of a type in accordance with ISO 603-15 3.103 cut-off machin

44、e tool designed to cut by means of a rotating abrasive cut-off wheel (bonded reinforced or diamond), where the wheel is fixed on a spindle which is mounted on a cutting unit, the machine is equipped with a table which supports and positions the workpiece fixed in a vice and the cutting unit is fitte

45、d to an arm which projects over the table from a pivot located at the table or on part of the frame of the machine Note 1 to entry: See Figure 101. 3.104 cutting unit device with an affixed cut-off wheel, capable of generating a cutting action 3.105 D maximum specified diameter of the wheel 3.106 di

46、amond wheel wheel made of metal with a continuous or segmented abrasive rim 3.107 fence device to position the workpiece and absorb the horizontal forces from the wheel during the cutting process 3.108 outer flange part that supports the front side of the wheel and secures and clamps the wheel to th

47、e spindle and the inner flange 3.109 rest position uppermost position of the cutting unit intended by design 3.110 wheel guard guard which partly encloses the wheel and gives protection to the operator 4 General requirements This clause of Part 1 is applicable. 5 General conditions for the tests Thi

48、s clause of Part 1 is applicable, except as follows: 5.17 Addition: The mass of the tool shall include the wheel guard and the fence. 8 IEC 62841-3-10:2015 IEC 2015 Further parts such as carrying means that are required in accordance with the user instructions shall be included in the mass. 6 Radiat

49、ion, toxicity and similar hazards This clause of Part 1 is applicable. 7 Classification This clause of Part 1 is applicable. 8 Marking and instructions This clause of Part 1 is applicable, except as follows: 8.1 Addition: Tools shall also be marked with: the rated no-load speed of the output spindle. 8.2 Addition: Tools shall also be marked with the following safety warning: “ WARNING Always wear eye protection” or the sign M004 of ISO 7010 or th