IEC TR 62547-2013 Guideline for the measurement of high power damage sensitivity of single-mode fibre to bends - Guidance for interpretation of results《单模纤维弯曲高功率损伤敏感性的测量指南.结果解释导则》.pdf

《IEC TR 62547-2013 Guideline for the measurement of high power damage sensitivity of single-mode fibre to bends - Guidance for interpretation of results《单模纤维弯曲高功率损伤敏感性的测量指南.结果解释导则》.pdf》由会员分享，可在线阅读，更多相关《IEC TR 62547-2013 Guideline for the measurement of high power damage sensitivity of single-mode fibre to bends - Guidance for interpretation of results《单模纤维弯曲高功率损伤敏感性的测量指南.结果解释导则》.pdf（44页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC/TR 62547 Edition 2.0 2013-05 TECHNICAL REPORT Guidelines for the measurement of high-power damage sensitivity of single- mode fibre to bends Guidance for the interpretation of results IEC/TR 62547:2013(E) colour inside THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2013 IEC, Geneva, Switzerl

2、and All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country o

3、f the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fa

4、x: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publicat

5、ions The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Useful links: IEC publications search - www.iec.ch/searchpub The advanced search enables you to find IEC

6、 publications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new publicatio

7、ns released. Available on-line and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 30 000 terms and definitions in English and French, with equivalent terms in additional languages. Also know

8、n as the International Electrotechnical Vocabulary (IEV) on-line. Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Service Centre: csciec.ch. IEC/TR 62547 Edition 2.0 2013-05 TECHNICAL REPOR

9、T Guidelines for the measurement of high-power damage sensitivity of single- mode fibre to bends Guidance for the interpretation of results INTERNATIONAL ELECTROTECHNICAL COMMISSION W ICS 33.180.10 PRICE CODE ISBN 978-2-83220-801-4 Registered trademark of the International Electrotechnical Commissio

10、n Warning! Make sure that you obtained this publication from an authorized distributor. colour inside 2 TR 62547 IEC:2013(E) CONTENTS FOREWORD . 4 1 Scope . 6 2 Normative references . 6 3 Background 7 4 Test procedures . 9 4.1 Safety 9 Safety issues . 9 4.1.1Eye safe working . 9 4.1.2Risk of fire/fl

11、ame . 9 4.1.3Risk of atmospheric pollution from coating by-products 9 4.1.4Risk of fibre fuse initiation . 9 4.1.5Risk of damage to downstream components 10 4.1.6Risk avoidance 10 4.1.7 4.2 General . 10 4.3 Apparatus 10 Light source . 10 4.3.1Isolator 10 4.3.2Bend jig . 11 4.3.3Receiver 11 4.3.4Atte

12、nuator . 11 4.3.5Computer 11 4.3.6Camera . 11 4.3.7Thermal imaging camera . 11 4.3.8Oven . 11 4.3.9Sample 12 4.3.10 4.4 Test method 1 Failure time characterization as a function of the launch power and bend conditions (bend angle and diameter) 12 Description and procedure . 12 4.4.1General comments

13、and conclusions on test method 1 13 4.4.2Reported items for test method 1 . 14 4.4.3 4.5 Test method 2 Equilibrium temperature measurement 14 General . 14 4.5.1Coating heating measurements and power lost at bend . 16 4.5.2Analysis test method 2: equilibrium temperature . 17 4.5.3Test conditions for

14、test method 2 . 18 4.5.4Conclusions on test method 2 19 4.5.5Reported items for test method 2 . 19 4.5.6 5 Conclusions 20 Annex A (informative) Robustness of fibres against damage from exposure to high power at bends . 21 Bibliography 39 Figure 1 Example of experimental layout 11 Figure 2 Damage res

15、ults for fibre G 13 Figure 3 Example of time evolution of catastrophic high-power loss and related maximum temperature reached by the coating near to the top of the bent fibre (apex) 15 TR 62547 IEC:2013(E) 3 Figure 4 Sample FLIR camera output of the fibre bent under high power . 16 Figure 5 Depende

16、nce of the coating equilibrium temperature as a function of launched power and bend diameter for an IEC B1.2/ITU-T G.654 single-mode fibre (see reference 10) 16 Figure 6a Calculated from experimental test data at 1 360 nm 18 Figure 6b Extrapolated for 1 550 nm 18 Figure 6c Extrapolated for 1 625 nm

17、18 Figure 6 Maximum safe powers for 25 year life time as a function of bend radius enabling a safe coating temperature of 80 C for four single-mode fibre (sub-) categories . 18 Figure A.1 Clamping arrangements for high-power damage testing in 180 bends 23 Figure A.2 Clamping arrangement for high-pow

18、er damage testing in 90 bends . 23 Figure A.3 Typical R1 failure characteristics with a loss of greater than 10 dB . 24 Figure A.4 Typical R2 failure characteristics 24 Figure A.5 A schematic illustration of the three regimes . 24 Figure A.6 Monitor signal changes Typical for an R1 failure 25 Figure

19、 A.7 Monitor signal changes Typical for an R2 failure 25 Figure A.8 Damage results for fibre sample D 26 Figure A.9 High-power damage results at 90 and 180 for fibre D . 26 Figure A.10 Time to failure versus bend diameter at different launched powers . 27 Figure A.11 Bend loss performance at 180 (an

20、d 90 for comparison) for fibre D 28 Figure A.12 Power limitation for primary coated fibre . 28 Figure A.13 Comparison of power limitation for primary and secondary coated fibre D . 29 Figure A.14 Maximum optical power ensuring a 25 year lifetime and 180 bend loss versus bend diameter (from reference

21、 10). 30 Figure A.15 Maximum optical power ensuring a 25 year lifetime versus 180 bend loss . 30 Figure A.16 180 2-point OSA bend loss for fibre D 32 Figure A.17 180 2-point bend loss at 1 480 nm for fibre D . 32 Figure A.18 2-point bend loss for fibre D at various angles . 33 Figure A.19 180 2-poin

22、t bend loss at 1 480 nm for a range of fibres . 34 Figure A.20 Time to failure versus inverse of equilibrium temperature using an IEC B1.2/ITU-T G.654 single-mode fibre for bend diameters varying from 4 mm to 10 mm and launched power in the range 0,8 W to 3,2 W . 35 Figure A.21 Effect of baking prim

23、ary coated fibre C (reference 15) in an oven at constant temperature 35 Figure A.22 Time to failure for different coatings as a function of bend radius 37 Table A.1 Dependence of high-power damage on power entering coating 37 4 TR 62547 IEC:2013(E) INTERNATIONAL ELECTROTECHNICAL COMMISSION _ GUIDELI

24、NES FOR THE MEASUREMENT OF HIGH-POWER DAMAGE SENSITIVITY OF SINGLE-MODE FIBRE TO BENDS GUIDANCE FOR THE INTERPRETATION OF RESULTS FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC N

25、ational Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Pu

26、blicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- gov

27、ernmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC

28、 on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accep

29、ted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote internation

30、al uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the lat

31、ter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users shou

32、ld ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other dama

33、ge of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of

34、the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent right

35、s. The main task of IEC technical committees is to prepare International Standards. However, a technical committee may propose the publication of a technical report when it has collected data of a different kind from that which is normally published as an International Standard, for example “state o

36、f the art“. IEC 62547, which is a technical report, has been prepared by subcommittee 86A: Fibres and cables, of IEC technical committee 86: Fibre optics. This second edition cancels and replaces the first edition published in 2009, and constitutes a technical revision. The main changes with respect

37、 to the previous edition are listed below: updates related to B6 (bend-insensitive) category single-mode fibres); update to analysis for test method 2: Maximum temperature specification. TR 62547 IEC:2013(E) 5 The text of this technical report is based on the following documents: Enquiry draft Repor

38、t on voting 86A/1494/DTR 86A/1508/RVC Full information on the voting for the approval of this technical report can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. The committee has decided that the co

39、ntents of this publication will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. A bilingual

40、version of this publication may be issued at a later date. IMPORTANT The colour inside logo on the cover page of this publication indicates that it contains colours which are considered to be useful for the correct understanding of its contents. Users should therefore print this document using a col

41、our printer. 6 TR 62547 IEC:2013(E) GUIDELINES FOR THE MEASUREMENT OF HIGH-POWER DAMAGE SENSITIVITY OF SINGLE-MODE FIBRE TO BENDS GUIDANCE FOR THE INTERPRETATION OF RESULTS 1 Scope This technical report describes two methods for the measurement of the sensitivity of single- mode optical fibres to hi

42、gh-power damage at bends: test method 1 Failure time characterisation as a function of the launch power and bend conditions (bend angle and bend diameter); test method 2 Equilibrium temperature measurement. Results from the two methods can only be compared qualitatively. The results in this report a

43、re predominantly on un-cabled and un-buffered fibres. Cabled and buffered fibres are expected to respond differently, because the outer layers can affect the ageing process. Note also that test method 2 testing cannot be applied to buffered or cabled fibres. These methods do not constitute a routine

44、 test to be used in the evaluation of optical fibre. The parameters derived from the two methods are not intended to be specified within a detailed fibre specification. The catastrophic failure modes arising and which are described in this document in general occur at bending radii much smaller than

45、 specified in the single-mode fibre specification IEC 60793-2-50 or than would be recommended based on mechanical reliability considerations alone. This report includes several annexes, including a discussion on the rationale for the approaches adopted, metrics for assessment, guidance, examples and

46、 some conclusions from initial studies. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the

47、referenced document (including any amendments) applies. IEC 60793-1-47, Optical fibres Part 1-47: Measurement methods and test procedures Macrobending loss IEC 60793-2-50, Optical fibres Part 2-50: Product specifications Sectional specification for class B single-mode fibres IEC 60825-1, Safety of l

48、aser products Part 1: Equipment classification and requirements IEC 60825-2, Safety of laser products Part 2: Safety of optical fibre communication systems (OFCS) TR 62547 IEC:2013(E) 7 IEC 61300-2-14, Fibre optic interconnecting devices and passive components Basic test and measurement procedures P

49、art 2-14: Tests High optical power IEC/TR 61292-4, Optical amplifiers Part 4: Maximum permissible optical power for the damage-free and safe use of optical amplifiers, including Raman amplifiers 3 Background Optical network operators have been considering the use of high-power lasers, for example fibre Raman amplifiers, in the central office with typical launch powers in