IEC 62718-2013 Railway applications - Rolling stock - D.C supplied electronic ballasts for lighting fluorescent lamps《铁路应用设施.铁道车辆.照明荧光灯用直流电子镇流器》.pdf

《IEC 62718-2013 Railway applications - Rolling stock - D.C supplied electronic ballasts for lighting fluorescent lamps《铁路应用设施.铁道车辆.照明荧光灯用直流电子镇流器》.pdf》由会员分享，可在线阅读，更多相关《IEC 62718-2013 Railway applications - Rolling stock - D.C supplied electronic ballasts for lighting fluorescent lamps《铁路应用设施.铁道车辆.照明荧光灯用直流电子镇流器》.pdf（82页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 62718 Edition 1.0 2013-04 INTERNATIONAL STANDARD NORME INTERNATIONALE Railway applications Rolling stock DC supplied electronic ballasts for lighting fluorescent lamps Applications ferroviaires Matriel roulant Ballasts lectroniques courant continu pour lampes fluorescentes dclairage IEC 62718:2

2、013 THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2013 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permissi

3、on in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for fu

4、rther information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de la CEI ou du C

5、omit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsidence. IEC Central Office Tel.:

6、+41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and rela

7、ted technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Useful links: IEC publications search - www.iec.ch/searchpub The adv

8、anced search enables you to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just

9、Published details all new publications released. Available on-line and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 30 000 terms and definitions in English and French, with equivalent term

10、s in additional languages. Also known as the International Electrotechnical Vocabulary (IEV) on-line. Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Service Centre: csciec.ch. A propos de

11、la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI Le contenu technique des publications de la

12、CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Liens utiles: Recherche de publications CEI - www.iec.ch/searchpub La recherche avance vous permet de trouver des publications CEI en utilisant diffrents critres

13、(numro de rfrence, texte, comit dtudes,). Elle donne aussi des informations sur les projets et les publications remplaces ou retires. Just Published CEI - webstore.iec.ch/justpublished Restez inform sur les nouvelles publications de la CEI. Just Published dtaille les nouvelles publications parues. D

14、isponible en ligne et aussi une fois par mois par email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 30 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans les langues addi

15、tionnelles. Egalement appel Vocabulaire Electrotechnique International (VEI) en ligne. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions contactez-nous: csciec.ch. IEC 62718 Edition 1.0 2013-04 INTERNATIONAL STANDARD

16、 NORME INTERNATIONALE Railway applications Rolling stock DC supplied electronic ballasts for lighting fluorescent lamps Applications ferroviaires Matriel roulant Ballasts lectroniques courant continu pour lampes fluorescentes dclairage INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECH

17、NIQUE INTERNATIONALE W ICS 45.060 PRICE CODE CODE PRIX ISBN 978-2-83220-752-9 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale Warning! Make sure that you obtained this publication from an authorized distributor. Atte

18、ntion! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. 2 62718 IEC:2013 CONTENTS FOREWORD . 4 INTRODUCTION . 6 1 Scope . 7 2 Normative references 7 3 Terms and definitions . 8 3.1 General terms 8 3.2 Lamps and characteristics . 9 4 Classification 10 5 Characteri

19、stics 10 5.1 Rated voltages. 10 5.2 Overvoltages . 10 5.3 Type of fluorescent lamps 10 6 Product information . 11 6.1 Nature of information . 11 6.1.1 General . 11 6.1.2 Identification 11 6.1.3 Characteristics . 11 6.1.4 Other characteristics and information for installation. 11 6.2 Marking . 11 6.3

20、 Instructions for storage, installation, operation and maintenance 12 7 Normal service conditions . 12 8 Constructional and performance requirements 12 8.1 Constructional requirements 12 8.1.1 General . 12 8.1.2 Dimensions and wiring diagram 12 8.1.3 Terminals 12 8.1.4 Provisions for repair . 12 8.1

21、.5 Clearance and creepage distances . 13 8.1.6 Protection 13 8.1.7 Inrush current 13 8.2 Performance requirements . 13 8.2.1 Electronic ballast parameters in accordance with lamps characteristics . 13 8.2.2 Exceptional conditions of use . 14 8.2.3 Electronic ballast design requirements . 15 8.2.4 In

22、stallation requirements 16 8.3 Safety requirements . 17 9 Tests 17 9.1 Test conditions 17 9.1.1 Environmental conditions . 17 9.1.2 Other conditions 18 9.2 Kinds of tests . 18 9.2.1 Type tests 18 9.2.2 Routine tests . 19 9.2.3 Investigatory tests 20 9.3 Verification of constructional and performance

23、 requirements 20 62718 IEC:2013 3 9.3.1 General . 20 9.3.2 Sequence 1 . 20 9.3.3 Sequence 2 . 22 9.3.4 Sequence 3 . 24 9.3.5 Sequence 4 . 25 9.3.6 Sequence 5 . 27 Annex A (informative) Distance between lamp and metallic support 29 Annex B (informative) Electronic ballast for lamps up to 40 W (case 1

24、) . 30 Annex C (informative) Electronic ballast for lamps up to 40 W (case 2) . 31 Annex D (informative) Electronic ballast for lamps up to 15 W 32 Annex E (informative) Electronic ballast for lamps up to 20 W. 33 Annex F (informative) Electronic ballast for lamps up to 10 W . 34 Annex G (informativ

25、e) Basic schematic diagrams . 35 Bibliography 38 Figure 1 Test circuit . 22 Figure 2 Current limiting curve 23 Figure 3 Circuit for leakage current measurement . 24 Figure 4 Circuit for test B: Cathode deactivated (rectifying effect) . 26 Figure B.1 Overall dimensions for electronic ballast 30 Figur

26、e C.1 Overall dimensions for electronic ballast 31 Figure D.1 Overall dimensions for electronic ballast 32 Figure E.1 Overall dimensions for electronic ballast 33 Figure F.1 Overall dimensions for electronic ballast 34 Figure G.1 One or two tubular lamps 35 Figure G.2 One or two tubular lamps 35 Fig

27、ure G.3 One or two tubular lamps 36 Figure G.4 One tubular lamp 36 Figure G.5 One tubular lamp 36 Figure G.6 One or two single capped lamps 36 Figure G.7 One single capped lamp 37 Table 1 Type tests 19 Table 2 Routine tests . 20 Table 3 Dielectric test voltage values 22 4 62718 IEC:2013 INTERNATIONA

28、L ELECTROTECHNICAL COMMISSION _ RAILWAY APPLICATIONS ROLLING STOCK DC SUPPLIED ELECTRONIC BALLASTS FOR LIGHTING FLUORESCENT LAMPS FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC N

29、ational Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Pu

30、blicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- gov

31、ernmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC

32、 on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accep

33、ted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote internation

34、al uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the lat

35、ter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users shou

36、ld ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other dama

37、ge of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of

38、the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent right

39、s. International Standard IEC 62718 has been prepared by IEC technical committee 9: Electrical equipment and systems for railways. This standard is based on EN 50311:2003. The text of this standard is based on the following documents: FDIS Report on voting 9/1769A/FDIS 9/1798/RVD Full information on

40、 the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. 62718 IEC:2013 5 The committee has decided that the contents of this publication will remain unchanged

41、 until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. 6 62718 IEC:2013 INTRODUCTION This International Standard ha

42、s been developed specifically for railway applications, to supplement the current standards. It covers general safety and performance requirements in addition to or in place of those contained in IEC 61347-1, IEC 61347-2-3 and 61347-2-7. NOTE 1 When applied unchanged, the clauses of IEC 61347 are ei

43、ther referred in this standard or introduced into it if they are short texts. NOTE 2 When a clause of IEC 61347 applies with changes or is replaced by more specific requirements, generally a short note explains the difference or the reason for that. 62718 IEC:2013 7 RAILWAY APPLICATIONS ROLLING STOC

44、K DC SUPPLIED ELECTRONIC BALLASTS FOR LIGHTING FLUORESCENT LAMPS 1 Scope This International Standard specifies the performance and constructional requirements, and associated tests, for d.c. supplied electronic ballasts used to supply fluorescent lamps for lighting on railway rolling stock. Its requ

45、irements replace those of IEC 61347 for all railway rolling stock applications and specify and complete those of IEC 61347 for the specific needs of railway rolling stock applications. This international standard applies to electronic ballasts supplying pre-heated cathode fluorescent lamps without i

46、ntegrated starters, tubular or single capped, according to IEC 60081 and IEC 60901 respectively, having a single and non adjustable luminous flux level. It does not apply to electronic ballasts supplying non pre-heated cathode lamps and/or lamps with integrated starters. 2 Normative references The f

47、ollowing documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60068-2-

48、1:2007, Environmental testing Part 2-1: Tests Test A: Cold IEC 60068-2-2:2007, Environmental testing Part 2-2: Tests Test B: Dry heat IEC 60068-2-30:2005, Environmental testing Part 2-30: Tests Test Db: Damp heat, cyclic (12h + 12h cycle) IEC 60077-1:1999, Railway applications Electric equipment for

49、 rolling stock Part 1: General service conditions and general rules IEC 60417, Graphical symbols for use on equipment Available from:http/www.graphical- symbols.info/equipment IEC 60529:1989, Degrees of protection provided by enclosures (IP code) 1IEC 60571:2012, Railway applications Electronic equipment used on rolling stock IEC 60598-1:2008, Luminaries Part 1: Gen