IEC 62374-1-2010 Semiconductor devices - Part 1 Time-dependent dielectric breakdown (TDDB) test for inter-metal layers《半导体器件.第1部分 金属层之间的时间相关的介质击穿(TDDB)试验》.pdf

《IEC 62374-1-2010 Semiconductor devices - Part 1 Time-dependent dielectric breakdown (TDDB) test for inter-metal layers《半导体器件.第1部分 金属层之间的时间相关的介质击穿(TDDB)试验》.pdf》由会员分享，可在线阅读，更多相关《IEC 62374-1-2010 Semiconductor devices - Part 1 Time-dependent dielectric breakdown (TDDB) test for inter-metal layers《半导体器件.第1部分 金属层之间的时间相关的介质击穿(TDDB)试验》.pdf（36页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 62374-1 Edition 1.0 2010-09 INTERNATIONAL STANDARD NORME INTERNATIONALE Semiconductor devices Part 1: Time-dependent dielectric breakdown (TDDB) test for inter-metal layers Dispositifs semiconducteurs Partie 1: Essai de rupture dilectrique en fonction du temps (TDDB) pour les couches intermtall

2、iques IEC 62374-1:2010 colour inside THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2010 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopyin

3、g and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC

4、 member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sa

5、ns laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rs

6、idence. IEC Central Office 3, rue de Varemb CH-1211 Geneva 20 Switzerland Email: inmailiec.ch Web: www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and re

7、lated technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Catalogue of IEC publications: www.iec.ch/searchpub The IEC on-lin

8、e Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, withdrawn and replaced publications. IEC Just Published: www.iec.ch/online_news/justpub Stay up to date on all new IEC publications. Just Published detail

9、s twice a month all new publications released. Available on-line and also by email. Electropedia: www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions in English and French, with equivalent terms in additional

10、languages. Also known as the International Electrotechnical Vocabulary online. Customer Service Centre: www.iec.ch/webstore/custserv If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service Centre FAQ or contact us: Email: csciec.ch Tel.:

11、 +41 22 919 02 11 Fax: +41 22 919 03 00 A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publicati

12、ons CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm Le Catalogue en-ligne de la CEI vous

13、permet deffectuer des recherches en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Il donne aussi des informations sur les projets et les publications retires ou remplaces. Just Published CEI: www.iec.ch/online_news/justpub Restez inform sur les nouvelles publications de la CE

14、I. Just Published dtaille deux fois par mois les nouvelles publications parues. Disponible en-ligne et aussi par email. Electropedia: www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 20 000 termes et dfinitions en anglais et en

15、franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International en ligne. Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des ques

16、tions, visitez le FAQ du Service clients ou contactez-nous: Email: csciec.ch Tl.: +41 22 919 02 11 Fax: +41 22 919 03 00 IEC 62374-1 Edition 1.0 2010-09 INTERNATIONAL STANDARD NORME INTERNATIONALE Semiconductor devices Part 1: Time-dependent dielectric breakdown (TDDB) test for inter-metal layers Di

17、spositifs semiconducteurs Partie 1: Essai de rupture dilectrique en fonction du temps (TDDB) pour les couches intermtalliques INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE P ICS 31.080 PRICE CODE CODE PRIX ISBN 978-2-88912-178-6 Registered trademark of the Inte

18、rnational Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale colour inside 2 62374-1 IEC:2010 CONTENTS FOREWORD.3 1 Scope.5 2 Terms and definitions .5 3 Test equipment.6 4 Test samples6 4.1 General .6 4.2 Test structure6 5 Procedures.8 5.1 General .8 5.2 Pre-te

19、st .8 5.3 Test conditions8 5.3.1 General .8 5.3.2 Electric field 8 5.3.3 Temperature9 5.4 Failure criterion .9 6 Lifetime estimation .10 6.1 General .10 6.2 Acceleration model10 6.3 Formula of E model .10 6.4 A procedure for lifetime estimation 10 7 Lifetime dependence on inter-metal layer area .13

20、8 Summary13 Annex A (informative) Engineering supplementation for lifetime estimation 14 Bibliography16 Figure 1 Schematic image of test structure (comb and serpent pattern) .7 Figure 2 Schematic image of test structure (comb and comb pattern) 7 Figure 3 Cross-sectional image of test structure for l

21、ine to stacked line including via.8 Figure 4 Cross-sectional image of test structure for stacked line to stacked line including via .8 Figure 5 Test flow diagram of constant voltage stress method .9 Figure 6 Weibull distribution plot11 Figure 7 Procedure to estimate the acceleration factor due to th

22、e electric field dependence12 Figure 8 Procedure to estimate the activation energy using an Arrhenius plot12 62374-1 IEC:2010 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ SEMICONDUCTOR DEVICES Part 1: Time-dependent dielectric breakdown (TDDB) test for inter-metal layers FOREWORD 1) The Internation

23、al Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic

24、fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any

25、 IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standard

26、ization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has repre

27、sentation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC

28、 cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional public

29、ations. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas

30、, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents includin

31、g individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance

32、 upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the eleme

33、nts of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 62374-1 has been prepared by IEC technical committee 47: Semiconductor devices. The text of this standard is based on the follo

34、wing documents: FDIS Report on voting 47/2063/FDIS 47/2077/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all the pa

35、rts in the IEC 62374 series, under the general title Semiconductor devices, can be found on the IEC website. 4 62374-1 IEC:2010 The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ i

36、n the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. IMPORTANT The colour inside logo on the cover page of this publication indicates that it contains colours which are considered to be useful for the

37、 correct understanding of its contents. Users should therefore print this document using a colour printer. 62374-1 IEC:2010 5 SEMICONDUCTOR DEVICES Part 1: Time-dependent dielectric breakdown (TDDB) test for inter-metal layers 1 Scope This part of IEC 62374 describes a test method, test structure an

38、d lifetime estimation method of the time-dependent dielectric breakdown (TDDB) test for inter-metal layers applied in semiconductor devices. 2 Terms and definitions For the purposes of this document, the following terms and definitions apply. 2.1 leakage current of inter-metal layer I leakcurrent th

39、rough the dielectric layer when a use voltage is applied 2.2 initial leakage current of inter-metal layer I leak-0leakage current of inter-metal layer before a stress voltage is applied 2.3 compliance current I comp maximum current of the voltage-forcing equipment NOTE A compliance limit can be spec

40、ified for a particular test. 2.4 measured leakage current of inter-metal layer I meas measured current in constant voltage stress (CVS) test 2.5 breakdown time t bdsummation of time during which stress voltage is applied to inter-metal layer until failure NOTE In CVS test, applied stress voltage is

41、interrupted by measuring and assessing repeatedly (see Figure 5). 2.6 dielectric layer thickness t d physical thickness of dielectric layer which is pitched between metal lines 2.7 stress voltage V stressvoltage applied during CVS test 6 62374-1 IEC:2010 2.8 use voltage V use voltage applied during

42、pre-test and used for lifetime estimation NOTE This voltage is usually power supply voltage. 2.9 metal electrode length L total length of metal electrode which is pitching the dielectric layer 2.10 electric field for inter-metal layer E imvoltage across a dielectric layer divided by its horizontal w

43、idth between metal lines NOTE The dielectric layer width should be determined by a consistent documented method by the physical measurement method with SEM, TEM or other. The method or a reference to a documented standard which describes the method should be included in the data report. 3 Test equip

44、ment This TDDB test can be applied by both the package level test and the wafer level test. A high temperature oven is used for the package level test. In the case of the wafer level test, a wafer probe with a hot plate or hot chuck is necessary. Additionally the instruments need to have sufficient

45、resolution to detect changes of leakage current under high temperature condition. NOTE Package level test is test on test structures assembled in package. 4 Test samples 4.1 General Test samples for TDDB test for inter-metal layer shall have the following test structure. 4.2 Test structure An approp

46、riate test structure for this test is an interdigitated one as shown in Figure 1, consisting of comb and serpent patterns, which are connected to the voltage source lines. There is an alternative structure, that is the interdigitated comb and comb structure shown in Figure 2. Test structure leads sh

47、all be designed to prevent unexpected failures outside the test structure during the TDDB test. Patterns with vias (Figures 3 and 4) need to be considered because the failure mechanism might be different from a line-to-line pattern without via. Unless otherwise specified comb and serpent pattern are

48、 be recommended. The minimum line-to-line spacing is the most severe condition for this mechanism. Therefore, the minimum dimension allowed by the layout rule shall be evaluated. The total length of the metal line is recommended to be in the range from 0,01 m to 1 m. For the accurate lifetime estima

49、tion, it is recommended that at least three device conditions of area or length be used, so proper scaling can be achieved. Unless otherwise specified the above-mentioned conditions shall be used for test structure parameters. 62374-1 IEC:2010 7 Width of dielectric layer Metal line (serpent pattern) Metal line (comb pattern) Dielectric layer between metal lines V V GND Metal line (comb pattern) IEC 2106