IEC 62321-1-2013 Determination of certain substances in electrotechnical products - Part 1 Introduction and overview《电工制品中特定物质的测定.第1部分 简介和概述》.pdf

《IEC 62321-1-2013 Determination of certain substances in electrotechnical products - Part 1 Introduction and overview《电工制品中特定物质的测定.第1部分 简介和概述》.pdf》由会员分享，可在线阅读，更多相关《IEC 62321-1-2013 Determination of certain substances in electrotechnical products - Part 1 Introduction and overview《电工制品中特定物质的测定.第1部分 简介和概述》.pdf（38页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 62321-1 Edition 1.0 2013-05 INTERNATIONAL STANDARD NORME INTERNATIONALE Determination of certain substances in electrotechnical products Part 1: Introduction and overview Dtermination de certaines substances dans les produits lectrotechniques Partie 1: Introduction et prsentation IEC 62321-1:20

2、13 colour inside THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2013 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, wit

3、hout permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Com

4、mittee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de l

5、a CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsidence. IEC Central

6、Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electr

7、onic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Useful links: IEC publications search - www.iec.ch/sear

8、chpub The advanced search enables you to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new IEC public

9、ations. Just Published details all new publications released. Available on-line and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 30 000 terms and definitions in English and French, with eq

10、uivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary (IEV) on-line. Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Service Centre: csciec.ch.

11、 A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI Le contenu technique des public

12、ations de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Liens utiles: Recherche de publications CEI - www.iec.ch/searchpub La recherche avance vous permet de trouver des publications CEI en utilisant diffr

13、ents critres (numro de rfrence, texte, comit dtudes,). Elle donne aussi des informations sur les projets et les publications remplaces ou retires. Just Published CEI - webstore.iec.ch/justpublished Restez inform sur les nouvelles publications de la CEI. Just Published dtaille les nouvelles publicati

14、ons parues. Disponible en ligne et aussi une fois par mois par email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 30 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans les

15、 langues additionnelles. Egalement appel Vocabulaire Electrotechnique International (VEI) en ligne. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions contactez-nous: csciec.ch. IEC 62321-1 Edition 1.0 2013-05 INTERNA

16、TIONAL STANDARD NORME INTERNATIONALE Determination of certain substances in electrotechnical products Part 1: Introduction and overview Dtermination de certaines substances dans les produits lectrotechniques Partie 1: Introduction et prsentation INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION E

17、LECTROTECHNIQUE INTERNATIONALE Q ICS 13.020; 43.040.10 PRICE CODE CODE PRIX ISBN 978-2-83220-815-1 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale Warning! Make sure that you obtained this publication from an authori

18、zed distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. colour inside 2 62321-1 IEC:2013 CONTENTS FOREWORD . 3 INTRODUCTION . 5 1 Scope . 6 2 Normative references . 6 3 Terms, definitions and abbreviations 6 Terms and definitions 6 3.1Abbrevi

19、ations 8 3.2 4 Test methods Overview . 8 Field of application 8 4.1Sample 9 4.2Test methods Flow chart . 9 4.3Quality assurance and control . 12 4.4Blank solution 12 4.5Adjustment to the matrix 12 4.6Limits of detection (LOD) and limits of quantification (LOQ) . 12 4.7Test report 13 4.8Alternative t

20、est methods 13 4.9 Annex A (informative) Limit of detection (LOD) or method detection limit (MDL) Example of calculation 14 Bibliography 16 Figure 1 Flow chart of the test methods . 10 Table 1 Overview of typical screening and verification testing procedure elements Preparation . 11 Table 2 Overview

21、 of typical screening and verification testing procedure elements Substance type . 12 Table A.1 Experimental results 14 Table A.2 Students t-values (t-statistic) 14 Table A.3 Calculation results . 15 62321-1 IEC:2013 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ DETERMINATION OF CERTAIN SUBSTANCES I

22、N ELECTROTECHNICAL PRODUCTS Part 1: Introduction and overview FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international c

23、o-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred

24、 to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in th

25、is preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an internation

26、al consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable e

27、fforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Public

28、ations transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. I

29、ndependent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7)

30、No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for cost

31、s (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct applica

32、tion of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 62321-1 has been prepared by IEC techn

33、ical committee 111: Environmental standardization for electrical and electronic products and systems. The first edition of IEC 62321:2008 was a stand-alone standard that included an introduction, an overview of test methods, a mechanical sample preparation as well as various test method clauses. Thi

34、s first edition of IEC 62321-1 is a partial replacement of IEC 62321, forming a structural revision and replacing Clauses 1 to 4. Future parts in the IEC 62321 series will gradually replace the corresponding clauses from IEC 62321:2008. Until such time as all parts are published, however, IEC 62321:

35、2008 remains valid for those clauses not yet re-published as a separate part. 4 62321-1 IEC:2013 The text of this standard is based on the following documents: FDIS Report on voting 111/295/FDIS 111/306/RVD Full information on the voting for the approval of this standard can be found in the report o

36、n voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all parts in the IEC 62321 series can be found on the IEC website under the general title: Determination of certain substances in electrotechnical products. The commi

37、ttee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised editi

38、on, or amended. IMPORTANT The colour inside logo on the cover page of this publication indicates that it contains colours which are considered to be useful for the correct understanding of its contents. Users should therefore print this document using a colour printer. 62321-1 IEC:2013 5 INTRODUCTIO

39、N The widespread use of electrotechnical products has drawn increased attention to their impact on the environment. In many countries this has resulted in the adoption of regulations affecting wastes, substances and energy use of electrotechnical products. The use of certain substances (e.g. lead (P

40、b), cadmium (Cd) and polybrominated diphenyl ethers (PBDEs) in electrotechnical products, is a source of concern in current and proposed regional legislation. The purpose of the IEC 62321 series is therefore to provide test methods that will allow the electrotechnical industry to determine the level

41、s of certain substances of concern in electrotechnical products on a consistent global basis. The first edition of IEC 62321:2008 was a single stand-alone standard that included an introduction, an overview of test methods, a mechanical sample preparation as well as various test method clauses. The

42、structure of the new multi-part IEC 62321 series comprises: Determination of certain substances in electrotechnical products Part 1: Introduction and overview. Determination of certain substances in electrotechnical products Part 2: Disassembly, disjointment and mechanical sample preparation. The re

43、maining parts specify screening and verification test methods for the determination of certain substances, each part representing a given substance. WARNING Persons using this International Standard should be familiar with normal laboratory practice. This standard does not purport to address all of

44、the safety problems, if any, associated with its use. It is the responsibility of the user to establish appropriate safety and health practices and to ensure compliance with any national regulatory conditions. 6 62321-1 IEC:2013 DETERMINATION OF CERTAIN SUBSTANCES IN ELECTROTECHNICAL PRODUCTS Part 1

45、: Introduction and overview 1 Scope This part of IEC 62321 refers to the sample as the object to be processed and measured. The nature of the sample and the manner in which it is acquired is defined by the entity carrying out the tests and not by this standard. It is noted that the selection of the

46、sample may affect the interpretation of the test results. While this standard provides guidance on the disassembly procedure employed for obtaining a sample, it does not determine or specify: the level of the disassembly procedure required for obtaining a sample; the definition of a “unit” or “homog

47、enous material” as the sample; conformity assessment procedures. NOTE Further guidance on assessment procedures may be found in IEC/TR 62476 2. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application.

48、For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 78-2:1999, Chemistry Layouts for standards Part 2: Methods of chemical analysis ISO/IEC 17025, General requirements for the competence o

49、f testing and calibration laboratories 3 Terms, definitions and abbreviations Terms and definitions 3.1 For the purposes of this document, the following terms and definitions apply. 3.1.1 analyte substance to be measured 3.1.2 electronics material used in electrical or electronic equipment that is not metal or plastic (e.g. ceramic) or not uniform in composition throughout and cannot be practically d