UL SUBJECT 1351-2005 OUTLINE OF INVESTIGATION FOR HOSE REELS (Issue 1)《软管卷盘的调查大纲 发布编号 1》.pdf

《UL SUBJECT 1351-2005 OUTLINE OF INVESTIGATION FOR HOSE REELS (Issue 1)《软管卷盘的调查大纲 发布编号 1》.pdf》由会员分享，可在线阅读，更多相关《UL SUBJECT 1351-2005 OUTLINE OF INVESTIGATION FOR HOSE REELS (Issue 1)《软管卷盘的调查大纲 发布编号 1》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULOctober 4, 20051SUBJECT 1351OUTLINE OF INVESTIGATIONFORHOSE REELSIssue Number: 1OCTOBER 4, 2005Summary of TopicsThis first issue of Subject 1351, Outline of Investigation for Hose Reels,covers re

2、quirements for hose reels designed for the storage and handlingof hose in connection with oxygen-acetylene welding equipment.The UL Foreword is no longer located within the UL Standard. For informationconcerning the use and application of the requirements contained in thisStandard, the current versi

3、on of the UL Foreword is located onULStandardsInfoNet at: http:/ 2005 UNDERWRITERS LABORATORIES INC.UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULOCTOBER 4, 2005SUBJECT 13512No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURT

4、HER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULCONTENTSINTRODUCTION1 Scope .42 General 42.1 Components .4PERFORMANCE3 Leakage Test .44 Operation Test 55 Hydrostatic Strength Test 56 Accelerated Aging Test 57 Fuel Gas Compatibility Test 5APPENDIX AStandards for Components .A1OCTOBER 4, 200

5、5 SUBJECT 1351 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULINTRODUCTION1 Scope1.1 These requirements cover hose reels designed for the storage and handling of hose in connectionwith oxygen-acetylene welding equipment.1.2 Hose reels are to

6、 be used and installed in accordance with Standard for the Design and Installationof Oxygen-Fuel Gas Systems for Welding, Cutting, and Allied Processes, NFPA 51 and Safety in Welding,Cutting and Allied Processes, AWS/ANSI Z49.1.2 General2.1 Components2.1.1 Except as indicated in 2.1.2, a component o

7、f a product covered by this outline shall comply with therequirements for that component. See Appendix A for a list of standards covering components used in theproducts covered by this outline.2.1.2 A component is not required to comply with a specific requirement that:a) Involves a feature or chara

8、cteristic not required in the application of the component in theproduct covered by this standard, orb) Is superseded by a requirement in this standard.2.1.3 A component shall be used in accordance with its rating established for the intended conditions ofuse.PERFORMANCE3 Leakage Test3.1 One sample

9、of each size of hose reel and hose (if supplied), shall be subjected to test. The oxygenside shall be subjected to aerostatic pressure of 600 psig and the acetylene side shall be subjected toaerostatic pressure of 100 psig. The test pressure shall be maintained for 1 minute.3.2 No external leakage s

10、hall be observed.3.3 The test shall be performed before and after the Operation Test, Section 4.OCTOBER 4, 2005SUBJECT 13514UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM UL4 Operation Test4.1 Each size of hose reel assembly, with hose (if supp

11、lied), shall be subjected to 50,000 cycles ofoperation. One cycle shall include at least one revolution of the reel assembly in one direction, and itsreturn to the initial position. The reel and hose shall be continuously pressurized to 75 psig for the durationof the test.4.2 No external leakage or

12、damage to the hose (if supplied), shall be observed after the test.5 Hydrostatic Strength Test5.1 Each size of hose reel with hose, if supplied, shall be subjected to a hydrostatic test pressure of 5times the maximum working pressure, not less than 500 psig maintained for 1 minute.5.2 The reel shall

13、 show no evidence of rupture or distortion and the hose shall not burst.6 Accelerated Aging Test6.1 Representative samples of the elastomer parts shall be subjected to 70 h in an air oven at 100 2C(212 3.6F). The samples shall be subjected to a visual inspection before and after the air oven aging.T

14、he samples shall still be flexible and show no apparent deterioration after the air oven aging.7 Fuel Gas Compatibility Test7.1 Samples of nonmetallic components of the device are subjected to immersion tests for 70 h at roomtemperature in test liquids in accordance with Table 7.1. Volume change and

15、 weight loss determinationsare made after immersion. Volume change shall be within the limits of minus 1 to 25 percent. A maximumweight loss of 10 percent is allowed.Table 7.1Test liquidsFluid in contact with part Test fuel gases and pressureAcetylene, hydrogen Test waivedLP-Gas N-hexaneMPS-gas MPS-

16、gasNatural gas, methane IRM oil No. 903 and N-hexane7.2 With reference to the requirement in 7.1, when the limits for volume-change or weight-loss areexceeded, a complete sample is to be filled with the appropriate test liquid for 70 hours, following whichthe assembly shall comply with the requireme

17、nts of the Leakage Test, Section 3.OCTOBER 4, 2005 SUBJECT 1351 5UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULOCTOBER 4, 2005SUBJECT 13516No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WIT

18、HOUT PERMISSION FROM ULAPPENDIX AStandards for ComponentsStandards under which components of the products covered by this outline are evaluated include thefollowing:Title of Standard UL Standard DesignationHose and Hose Assemblies for Dispensing Flammable Liquids UL 330OCTOBER 4, 2005 SUBJECT 1351 A1UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULOCTOBER 4, 2005SUBJECT 1351A2No Text on This Page