SSPC ME 1-1997 Uncontaminated Rusted Steel (Editorial Revisions November 1 2004)《洁净锈钢编辑修订 2004年11月1日》.pdf

《SSPC ME 1-1997 Uncontaminated Rusted Steel (Editorial Revisions November 1 2004)《洁净锈钢编辑修订 2004年11月1日》.pdf》由会员分享，可在线阅读，更多相关《SSPC ME 1-1997 Uncontaminated Rusted Steel (Editorial Revisions November 1 2004)《洁净锈钢编辑修订 2004年11月1日》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、SSPC-ME 1May 1, 1997Editorial Revisions November 1, 200411-1SSPC: The Society for Protective CoatingsTEST PANEL PREPARATION METHOD NO. 1Uncontaminated Rusted Steel1. Scope1.1 This specifi cation describes the requirements for preparing standard laboratory corroded test panels for use in evaluating c

2、oatings in accelerated or fence tests.1.2 Test panels prepared in accordance with this specifi -cation are intended primarily for evaluating the performance of coatings that are recommended for use on minimally prepared, minimally contaminated substrates. The test panels are intended to represent th

3、e minimally rusted steel surface after being cleaned to SSPC-SP 2 (Hand Tool Cleaning). 1.3 Test panels prepared in accordance with this speci-fi cation should not be used for evaluating the performance of coatings recommended for use over marine and industrial contaminated rusted steel.2. Descripti

4、on2.1 This is a method for preparing standard corroded test panels. The method is both rapid and reproducible. Steel panels are initially prepared in accordance with SSPC-SP 10 (Near White Metal Blast Cleaning) and then exposed in a cyclic wet/dry cabinet. This produces dense uniform corrosion produ

5、cts. The method employs deionized water and is not intended to deposit soluble ionic species on the substrates.3. Referenced Standards3.1 SSPC AND JOINT STANDARDS:PA 2 Measurement of Dry Coating Thickness with Magnetic GagesSP 1 Solvent CleaningSP 2 Hand Tool CleaningSP 10/NACE No. 2 Near White Meta

6、l Blast Cleaning3.5 AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) STANDARDS: A 36 Specifi cation for Carbon Structural SteelG 85 Standard Practice for Modifi ed Salt Spray (Fog) Testing (Annex A.5)4. Preparation of Test Panels4.1 Test panels shall be of A 36 steel with dimensions as agreed upon

7、between the purchaser and supplier.4.2 Test panels shall be solvent cleaned in accordance with SSPC-SP 1.4.3 Test panels shall be abrasive blast cleaned in accor-dance with SSPC-SP 10, using a contaminant-free manufactured abrasive such as aluminum oxide.5. Corrosion of Test Panels5.1 Test panels sh

8、all be exposed in a cyclic spray cabinet (see ASTM G 85, Annex A.5).5.2 The cyclic spray cabinet shall alternate between one hour wet (ambient temperature, deionized water) and one hour dry conditions (initial dry temperature 25C, fi nal dry temperature of 45C achieved after 30 minutes).5.3 The tota

9、l exposure time in the cyclic spray cabinet shall be 504 hours (three weeks). Panels shall be rotated through six positions in the cabinet such that each panel spends an equal amount of time at each position. The positions are the right, center, and left sides of the top and bottom rows of the cabin

10、et. The middle row of the cabinet shall not be used except with newer models of cabinets where it can be shown that temperature variations are not greater than those observed in the right, center, and left positions of the top and bottom rows.6. Inspection of Corroded Test Panels6.1 The corroded tes

11、t panels shall be uniformly corroded over the entire surface. Between-panel variations shall not be statistically signifi cant. Estimate uniformity of rusting by SSPC-PA 2, “Measurement of Dry Coating Thickness with Magnetic Gages.” NOTE: If the variation of rust thickness of a panel from the mean e

12、xceeds the requirement in Section 6.1.1, do not use such a panel.6.1.1 After measuring the rust thickness on each panel determine the mean rust thickness for the entire population of prepared panels. Determine the standard deviation from the mean rust thickness of the panel population. Discard any p

13、anels from the full population that are not within 2 standard deviations of the population mean rust thickness.7. Preparation and Storage of Test Panels Prior to Coating Application7.1 Corroded test panels may be stored indefi nitely under dry conditions prior to coating application and subsequent S

14、SPC-ME 1May 1, 1997Editorial Revisions November 1, 200411-2exposure testing.7.2 Corroded test panels shall be blown down with clean, dry compressed air prior to coating application.8. Disclaimer8.1 While every precaution is taken to ensure that all information furnished in SSPC standards and specifi

15、 cations is as accurate, complete, and useful as possible, SSPC cannot assume responsibility nor incur any obligation resulting from the use of any materials, coatings, or methods specifi ed herein, or of the specifi cation or standard itself.8.2 This specifi cation does not attempt to address prob-

16、lems concerning safety associated with its use. The user of this specifi cation, as well as the user of all products or practices described herein, is responsible for instituting appropriate health and safety practices and for ensuring compliance with all governmental regulations.Appendix ASupplemen

17、tary InformationThe utility of this method was evaluated in a research project conducted by SSPC and sponsored by the U.S. Army Construction Engineering Research Lab. Key results from this study are:A.1 Statistically high signifi cant agreement (correlation between two factors at the 99% confi dence

18、 level) is demon-strated between the unranked performance of coating systems applied to test panels prepared by this method when subjected to accelerated testing.A.2 Statistically signifi cant agreement (correlation be-tween two factors at the 95% confi dence level) is demonstrated between the unran

19、ked performance of coating systems applied to panels prepared by this method and naturally rusted surfaces when subjected to accelerated testing.A.3 Statistically high signifi cant agreement is demon-strated between the ranked performance of coatings applied to panels prepared by this method and naturally rusted surfaces when subjected to accelerated testing.