SANS 1176-2010 Self-supporting plastics containers of nominal capacities 5 L to 220 L《标称容量为5L至220L的自支撑塑料容器》.pdf

《SANS 1176-2010 Self-supporting plastics containers of nominal capacities 5 L to 220 L《标称容量为5L至220L的自支撑塑料容器》.pdf》由会员分享，可在线阅读，更多相关《SANS 1176-2010 Self-supporting plastics containers of nominal capacities 5 L to 220 L《标称容量为5L至220L的自支撑塑料容器》.pdf（30页珍藏版）》请在麦多课文档分享上搜索。

1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA

2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any

3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ISBN 978-0-626-23644-1 SANS 1176:2010Edition 3.1SOUTH AFRICAN NATIONAL STANDARD Self-supporting plastics containers of nominal capacities 5 L to 220 L Pu

4、blished by SABS Standards Division 1 Dr Lategan Road Groenkloof Private Bag X191 Pretoria 0001Tel: +27 12 428 7911 Fax: +27 12 344 1568 www.sabs.co.za SABS SANS 1176:2010 Edition 3.1 Table of changes Change No. Date Scope Amdt 1 2009 Amended to change the designation of SABS standards to SANS standa

5、rds, to update the definition for acceptable, to move reference to South African legislation in the text to the foreword, to delete a note on the obtainability of information about a suitable detergent, and to update referenced standards. Foreword This South African standard was approved by National

6、 Committee SABS TC 122, Packaging, in accordance with procedures of the SABS Standards Division, in compliance with annex 3 of the WTO/TBT agreement. This document was published in January 2010. This document supersedes SABS 1176:1994 (edition 2). A vertical line in the margin shows where the text h

7、as been technically modified by amendment No. 1. Reference is made in 4.1 to the “relevant national legislation“. In South Africa this means the Health Act, 1977 (Act No. 63 of 1977) (as amended from time to time). Annex A forms an integral part of this document. Annexes B, C, D, E, F and G are for

8、information only. SANS 1176:2010 Edition 3.1 1 Contents Page Foreword 1 Scope. 3 2 Normative references 3 3 Definitions 4 4 Requirements for materials 5 5 Construction. 6 6 Performance requirements 7 7 Marking 9 8 Methods of test 10 8.1 Impact test at 18 C C (tight-head containers for solid and liqu

9、id commodities of packaging groups I, II and III, open-head containers for solid commodities of packaging groups I, II and III and for liquid commodities of packaging groups II and III, and tight-head containers for commodities of packaging group IV). 10 02+8.2 Impact test at 18 C C (open-head conta

10、iners for commodities of packaging group IV). 12 02+8.3 Air leakage test (containers for liquids only). 12 8.4 Internal hydraulic pressure test (tight-head containers for liquids of packaging groups I, II and III and open-head containers for liquids of packaging groups II and III) . 13 8.5 Permeatio

11、n test (tight-head containers intended for reserve fuel for motor vehicles only (see 1.2). 13 8.6 Closure test (non-vented tight-head and open-head containers for liquids of packaging group IV only) 14 8.7 Stacking test . 14 8.8 Environmental stress cracking test. 17 8.9 Test for strength of handles

12、 17 Annex A (normative) Notes to purchasers. 19 Annex B (informative) Quality verification of self-supporting plastics containers 19 Annex C (informative) Test methods that can be used to establish the compatibility between plastics containers and substances. 20 Annex D (informative) Recommendations

13、 regarding the selection and re-use of containers . 22 Annex E (informative) Hazards arising from electrostatic build-up on containers used for flammable liquids . 23 Annex F (informative) Rerating of containers 24 Annex G (informative) Bibliography . 25 SANS 1176:2010 Edition 3.1 2 This page is int

14、entionally left blank SANS 1176:2010 Edition 3.1 3 Self-supporting plastics containers of nominal capacities 5 L to 220 L 1 Scope 1.1 This standard specifies the characteristics of self-supporting containers that are made of plastics materials, are of nominal capacities 5 L to 220 L, and are suitabl

15、e for the storage and transportation of substances in liquid or solid form. 1.2 This standard also covers self-supporting plastics containers, of maximum nominal capacity 10 L, for reserve fuel for motor vehicles. 1.3 When dangerous substances intended for export are packed in self-supporting plasti

16、cs containers, cognizance shall be taken of the applicable regulations of the following organizations: a) International Civil Aviation Organization (ICAO) technical instructions for the safe transport of dangerous goods by air; b) International Maritime Organization (IMO) international maritime dang

17、erous goods code (IMDG code); and c) regulations issued by other organizations with regard to the conveyance of dangerous goods and applicable in the importing country/countries, for example international convention concerning the carriage of dangerous goods by rail (RID), European agreement concern

18、ing the international carriage of dangerous goods by road (ADR) and Department of Transport, USA (DOT). 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this standard. All standards are subject to revision and, since an

19、y reference to a standard is deemed to be a reference to the latest edition of that standard, parties to agreements based on this standard are encouraged to take steps to ensure the use of the most recent editions of the standards indicated below. Information on currently valid national and internat

20、ional standards may be obtained from the SABS Standards Division. ASTM D445, Standard test method for kinematic viscosity of transparent and opaque liquids (and calculation of dynamic viscosity). ISO 2244, Packaging Complete, filled transport packages and unit loads. SANS 10228, The identification a

21、nd classification of dangerous goods for transport. SANS 10229-1, Transport of dangerous goods The packaging and large packaging for road and rail transport Part 1: Packaging. Amdt 1 SANS 1176:2010 Edition 3.1 4 3 Definitions For the purposes of this standard, the following definitions apply: 3.1 ac

22、ceptable acceptable to the authority administering this standard, or to the parties concluding the purchase contract, as relevant Amdt 1 3.2 container self-supporting container that is made of plastics material(s) and of which a) the body is predominantly cylindrical or rectangular in shape, and the

23、 body, top and bottom are moulded in one piece or combined to form one piece (tight-head style), or b) the body is predominantly cylindrical or rectangular in shape, the body and bottom are moulded in one piece, and the top is of circular configuration and of the removable type (open-head style) 3.3

24、 dangerous substances and goods substances and goods that are classified as such and allocated to packaging groups I, II or III in SANS 10228 3.4 defective container that fails in one or more respects to comply with the appropriate requirements of the standard 3.5 effective plastics material plastic

25、s material that is capable of performing the required functions and that a) is based on a polymer of a grade and quality recommended by the polymer manufacturer as being suitable for the specific purpose(s), b) contains no reground material other than material derived from clean and reworked materia

26、l from the manufacturers own production, and c) has not deteriorated during compounding and processing 3.6 flammable liquids class 3 substances identified in SANS 10228 and SANS 10229-1 Amdt 1 3.7 general goods non-dangerous substances not listed in SANS 10228 and low risk substances that may be lis

27、ted in SANS 10229-1, but are not assigned to packaging groups I, II or III. For the purposes of this standard, general goods are assigned to packaging group IV Amdt 1 3.8 liquid commodity the kinematic viscosity of which, determined in accordance with ASTM D445, does not exceed 1 650 mm2/s at 40 C S

28、ANS 1176:2010 Edition 3.1 5 3.9 non-invertible container open-head container or a container that has, at the top, a protruding neck or handle(s) or both, or that has a top the design of which is such that it is not practicable to stand or stack the container in the inverted position 3.10 packaging g

29、roup packagings are designed to offer protection and security of containment at different performance levels and are allocated to four groups as follows: packaging group I high strength packaging that offers a high degree of protection, prescribed for very dangerous goods packaging group II medium s

30、trength packaging that offers adequate protection for dangerous goods presenting a medium degree of danger packaging group III lowest grade of packaging prescribed for dangerous goods that still offers adequate protection for goods presenting a minor degree of danger packaging group IV (see also 3.7

31、) packaging prescribed for non-dangerous substances, designed to meet economic considerations, e.g. to prevent product loss, spoilage and contamination 3.11 self-supporting descriptive of a container that is strong enough not to require additional outer support 4 Requirements for materials 4.1 Conta

32、iners Containers shall be of an effective plastics material. The colour of the material of a finished container shall be an acceptable match to the colour required. Additives such as fillers, plasticizers, anti-static agents, pigments and inhibitors that are used in the plastics formulation shall be

33、 compatible with the polymer and shall not deleteriously affect the commodity for which the container is intended. The plastics material of a finished container shall be compatible with the commodity contained and such compatibility shall be established by an organization acceptable to the regulator

34、y authorities. In the case of containers intended for dangerous goods, the relevant requirements of SANS 10229-1 shall apply and in cases where substances for human consumption are packed, cognizance shall be taken of the relevant national legislation (see foreword). Amdt 1 NOTE Test procedures to d

35、etermine the compatibility of plastics containers and commodities, and that may be acceptable to the regulatory authorities, are given in annex C. 4.2 Requirements for closures Plastics closures of a material different from that of the container shall comply with the requirements of 4.1. SANS 1176:2

36、010 Edition 3.1 6 5 Construction 5.1 Style A container shall be of one of the styles given in 5.1.1 and 5.1.2, as required. 5.1.1 Tight-head (fixed-end, non-removable head) style The body, top and bottom and the flange(s) for the closure(s) shall be integral, i.e. moulded in one piece or combined to

37、 form one piece. There shall be either one or two closures of internal diameter not exceeding 70 mm at the top end of the container. The number, types and internal diameters of the closures shall be as required. The closures shall be so designed that they will seal efficiently, and threaded closures

38、 shall be resistant to “cork creep“. NOTE Tight-head containers may also be of the non-invertible style (see 3.9). 5.1.2 Open-head (removable head) style The body and bottom shall be integral, i.e. moulded in one piece. The lid (top) and the flange(s) (if any) shall be moulded in one piece. The numb

39、er (but not more than two), types and internal diameters of additional closures shall be as required. The lid and the rim of the container shall be such as to provide a good matching fit and, when so required, the joint shall be provided with a gasket. The lid shall be secured in position by means o

40、f a suitable clamping or strapping device that ensures a tight fit. 5.2 Handles Handles, if required, shall be of the type and number required, shall be of adequate size, and of strength such as to enable the container to comply with the requirements of 6.10. 5.3 Shape and dimensions The shape and d

41、imensions of a container shall be as required and shall make provision for the appropriate ullage (see 5.4). 5.4 Capacity The nominal capacity of a container shall be as required, and shall preferably be one of the following: 5 L, 10 L, 20 L, 25 L, 50 L, 100 L or 220 L. The actual capacity (i.e. the

42、 brimful capacity less the quantity displaced by the closure) shall be such that a) in the case of containers for liquid commodities, the liquid in the container would not fill the container when heated to 55 C, and b) in the case of containers for solid commodities, it exceeds the nominal capacity

43、by at least 1,5%. 5.5 Mass The mass of a finished container shall not differ by more than 3% from the nominal mass agreed upon. SANS 1176:2010 Edition 3.1 7 5.6 Finish and workmanship The finish and workmanship shall be such as to be acceptable. Both the inside and the outside of a container shall b

44、e acceptably free from pits and flashing, and pigmentation shall be evenly distributed. The finish of the sealing surfaces of a closure (of any type) shall be such that the closure complies with the requirements of 6.7. 6 Performance requirements 6.1 Containers for dangerous goods Plastics container

45、s intended for dangerous goods shall comply with the relevant performance requirements of SANS 10229-1. Amdt 1 NOTE Open-head containers are not permitted for liquid commodities of packaging group I. 6.2 Resistance to impact at 18 C C (tight-head containers for solid and liquid commodities of packag

46、ing groups I, II and III, open-head containers for solid commodities of packaging groups I, II and III and for liquid commodities of packaging groups II and III, and tight-head containers for commodities of packaging group IV) 02+When a container is tested in accordance with 8.1 by being dropped thr

47、ough the appropriate height given in column 2, 3 or 4 (as relevant) of table 1, it shall show no sign of failure liable to affect safety during transport. 6.3 Resistance to impact at 18 C C (open-head containers for commodities of packaging group IV) 02+When a container is tested in accordance with

48、8.2 by being dropped through the appropriate height given in column 2, 3 or 4 of table 1, it shall show no sign of failure. Table 1 Height of drop 1 2 3 4 Height of drop m Containers for liquids Packaging group Containers for solids Relative density of liquid commodity 1,2Relative density (d) of liq

49、uid commodity 1,2 I 1,8 1,8 d 1,5 II 1,2 1,2 d 1,0 III 0,8 0,8 d 0,67 IV 0,5 0,5 d 0,42 6.4 Resistance to air leakage (containers for liquids only) When a container is subjected in accordance with 8.3 to the appropriate internal air pressure given in table 2, it shall not leak. SANS 1176:2010 Edition 3.1 8 Table 2 Air pressure for air leakage test 1 2 3 Internal pressure (gauge) Style of container Packaging group kPa I 30 II or III 20 Tight-head IV 10 II or III 20 Open-head IV 10 6.5 Resistance to internal hydraulic p