SAE AS 81969 2-2012 INSTALLING AND REMOVAL TOOLS CONNECTOR ELECTRICAL CONTACT TYPE I CLASS I COMPOSITION C《C组I类I型电气连接器安装和拆卸工具》.pdf

《SAE AS 81969 2-2012 INSTALLING AND REMOVAL TOOLS CONNECTOR ELECTRICAL CONTACT TYPE I CLASS I COMPOSITION C《C组I类I型电气连接器安装和拆卸工具》.pdf》由会员分享，可在线阅读，更多相关《SAE AS 81969 2-2012 INSTALLING AND REMOVAL TOOLS CONNECTOR ELECTRICAL CONTACT TYPE I CLASS I COMPOSITION C《C组I类I型电气连接器安装和拆卸工具》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、 AEROSPACE STANDARD INSTALLING AND REMOVAL TOOLS, CONNECTOR ELECTRICAL CONTACT, TYPE I, CLASS I, COMPOSITION C AS81969/2Copyright 2017 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, elect

2、ronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 201

3、2-06REAFFIRMED 2017-06THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C2 FEDERAL SUPPLY CLASS 5120 AS81969/2 SHEET 1 OF 2 PROCUREMENT SPECIFICATION: AS81969 SAETechnicalStandardsBoard Rulesprovidethat:“Thisreportispublished bySAEto advance the state oftechnicaland engineering sciences.The use ofthisrepor

4、tisentirelyvoluntary,anditsapplicabilityandsuitabilityforanyparticularuse,includinganypatentinfringementarising therefrom,isthe sole responsibilityoftheuser.”SAEreviewseachtechnicalreportatleasteveryfiveyearsatwhich time itmaybe revised,reaffirmed,stabilized,orcancelled.SAEinvitesyourwritten comment

5、sandsuggestions.SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AS81969/2 RATIONALE AS81969/2 HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE FIVE-YEAR REVIEW POLICY. NOTICE THE COMPLETE REQUIREMENTS FOR PROCURING THE TOOLS AND ACCESSORIES DESCRIB

6、ED HEREIN SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF: SAE AS81969. FIGURE 1 M81969/2 TOOL CONFIGURATION AEROSPACE STANDARD AS81969/2 SHEET 2 OF 2 INSTALLING AND REMOVAL TOOLS, CONNECTOR ELECTRICAL CONTACT, TYPE I, CLASS I, COMPOSITION C TABLE 1 TOOL CONFIGURATION DASH NO. CONTACT SIZE A

7、MIN. B DIA. C D DIA. E MIN F MIN COLOR CODE -01 23-28 23-22 .085 .053 .051 .046 .042 .068 .065 .620 .465 YELLOW-02 20 .093 .081 .079 .060 .056 .105 .102 .620 .465 RED -03 16 .133 .106 .104 .074 .070 .134 .130 1.000 .710 BLUE -04 12 .174 .163 .161 .115 .110 .191 .187 1.000 .710 YELLOW REQUIREMENTS: A

8、S SPECIFIED IN AS81969 1. CONFIGURATION: UNLESS OTHERWISE SPECIFIED, DIMENSIONS ARE IN INCHES IN ACCORDANCE TABLE 1. OUTLINE CONFIGURATION OPTIONAL WITHIN MAXIMUM DIMENSIONS SHOWN. SLOT DESIGN SHALL ALLOW ALL APPLICABLE WIRE SIZES TO FIT INTO THE TOOL FREELY. BREAK SHARP CORNERS .005 INCH MAX RAD. U

9、NLESS OTHERWISE SPECIFIED. 2. MARKING: EACH TOOL SHALL BE LEGIBLY AND PERMANENTLY MARKED ON THE HANDLE IN ACCORDANCE WITH MIL-STD-130. 3. MATERIALS (SEE AS81969): HANDLE: PLASTIC PER L-P-1183 OR METAL TREATED TO RESIST CORROSION OR APPROVED EQUIVALENT. TOOL TIPS SHALL BE STAINLESS STEEL 440-SST OR 4

10、20-SS. HEAT TREATED TO ROCKWELL C48-52. 4. PLATING: NOT APPLICABLE. 5. PLUNGER FORCE: NOT APPLICABLE. 6. PART NUMBER M81969 /2 -01 I I I I I I_ DASH NUMBER (SEE TABLE 1) I I_ DETAIL SPECIFICATION NUMBER I_ BASIC SPECIFICATION NUMBER APPLICATION NOTES: 1. TOOLS ARE USED TO INSTALL AS39029/33, /46, AN

11、D 47 CONTACTS IN MIL-C-81511 SERIES 1 AND 2 CONNECTORS 2. AS81969/2 SUPERSEDES MIL-I-81969/2A WHICH SUPERSEDED MS3323 WHICH SUPERSEDED MS90459 (NAVY). PART NUMBERS REMAIN UNCHANGED. SPECIFICATION NOTES: 1. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING ARE

12、AS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.