SAE AS 1580E-2013 RING WELD 3000 PSI TITANIUM《3000 psi钛焊接环》.pdf

《SAE AS 1580E-2013 RING WELD 3000 PSI TITANIUM《3000 psi钛焊接环》.pdf》由会员分享，可在线阅读，更多相关《SAE AS 1580E-2013 RING WELD 3000 PSI TITANIUM《3000 psi钛焊接环》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、AEROSPACE STANDARD RING, WELD 3000 PSI, TITANIUM AS1580Copyright 2013 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without

2、 the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1980-02REAFFIRMED 2007-11 REVISED 2013-10THIRD ANGLE PROJECTION CUST

3、ODIAN: G-3/G-3B REV.EFEDERAL SUPPLY CLASS 4730 AS1580SHEET 1 OF 3REV. EPROCUREMENT SPECIFICATION: AS1576 /6/SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis report is entirely voluntary, andits appl

4、icability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised, reaffirmed, stabilized, orcancelled. SAE invites yourwrittencomments andsu

5、ggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS1580ERATIONALE REVISE ACTIVATION DATES FOR PRI-QPL-AS1576. FIGURE 1 - RING TABLE 1 - DIMENSIONS AND WEIGHTS BASIC NO. AS1580/16/SIZE CODE (NOMINAL TUBE SIZE)(NOMINALTUB

6、E WALL) A B.002/7/C/7/ D E R T.002 LB/100 APPROX REF 03040506081012162024.188 .250 .312 .375 .500 .625 .750 1.000 1.250 1.500 .016.016.020.020.026.033.039.052.065.074.222.284.342.411.542.668.7951.0461.2981.552.194.256.319.383.508.634.7591.0101.2601.510.167.229.285.348.465.581.698.9311.1631.403.058.0

7、58.064.064.074.092.094.098.104.108.020.020.023.023.028.037.038.040.043.045.005.005.005.005.005.006.006.007.007.007.014.014.014.014.017.017.018.018.019.021.0117 .0153 .0184 .0259 .0417 .0719 .0942 .137 .197 .266 AEROSPACE STANDARD AS1580SHEET 2 OF 3REV. ERING, WELD 3000 PSI, TITANIUM NOTES: /1/ MATER

8、IAL: CODE LETTER T - TYPE 6AL-4V TITANIUM ALLOY BAR PER AMS4928. 2. HEAT TREATMENT: NONE. 3. FINISH: NONE. /4/ CLEANING: a. NO SUFFIX CODE LETTER IN PART NUMBER - CLEAN BY ANY SUITABLE METHOD PER PROCUREMENT SPECIFICATION. b. SUFFIX CODE LETTER “C“ IN PART NUMBER - HOT ALKALINE CLEAN PER PROCUREMENT

9、 SPECIFICATION. c. SUFFIX CODE LETTER “E“ IN PART NUMBER - NITRIC-HYDROFLUORIC ACID ETCH PER PROCUREMENT SPECIFICATION. 5. PACKAGING: PER PROCUREMENT SPECIFICATION. /6/ PROCUREMENT SPECIFICATION: AS1576 UNLESS OTHERWISE SPECIFIED ON THIS STANDARD. PRODUCT SUPPLIED TO THIS SPECIFICATION SHALL BE MANU

10、FACTURED BY AN ACCREDITED MANUFACTURER AS LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LIST PRI-QPL-AS1576 FOR THIS STANDARD. SEE www.eAuditN FOR CURRENT QPL ONLINE. THIS QPL REQUIREMENT SHALL BE IN EFFECT FOR PURCHASE ORDERS PLACED ON OR AFTER JULY 1, 2014. SUPPLIERS SEEKING

11、LISTING ON THE INITIAL QPL MUST APPLY TO PRI FOR APPROVAL NO LATER THAN JANUARY 1, 2014. UNTIL THE QPL IS IN EFFECT, USERS OF THIS STANDARD ARE ADVISED TO CONTROL SOURCE APPROVALS. TRANSITION TO PRI-QPL SHALL BE COMPLETED BY JULY 1, 2014. /7/ DIMENSIONS “B“ AND “C“ SHALL NOT BE CONFIRMED IN THE FREE

12、 STATE CONDITION. FUNCTIONALITY AND FIT MAY BE VERIFIED BY INSTALLING THE RING ON THE TUBING SPECIFIED IN THE PROCUREMENT SPECIFICATION. AN OUT-OF-ROUND CONDITION WHICH DOES NOT PREVENT INSTALLATION OF THE RING SHALL NOT BE CAUSE FOR REJECTION. 8. IDENTIFICATION ON PACKAGES ONLY: SEE PROCUREMENT SPE

13、CIFICATION. 9. THIS PART IS DESIGNED FOR USE IN SYSTEMS WITH MAXIMUM OPERATING PRESSURES OF 3000 PSI WHEN ORBITAL ARC WELDED TO TITANIUM ALLOY TUBING. 10. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES

14、, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. 11.

15、INTERPRETATION OF DRAWING PER ARP4296. 12. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 MICROINCHES Ra. 13. BREAK EDGES AS SHOWN. 14. DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994 15. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .004. AEROSPACE STANDARD AS1580SHEET 3 OF 3REV. ERING, WELD 3000 PSI, TITANIUM /16/ EXAMPLE OF PART NUMBER: