PIA-TS-112-2011 Harness Container - AAD Installation Test Protocol《安全带 伞包 AAD装置试验协议 版本1 0》.pdf

《PIA-TS-112-2011 Harness Container - AAD Installation Test Protocol《安全带 伞包 AAD装置试验协议 版本1 0》.pdf》由会员分享，可在线阅读，更多相关《PIA-TS-112-2011 Harness Container - AAD Installation Test Protocol《安全带 伞包 AAD装置试验协议 版本1 0》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、September 2011 TS-112 v1.0 1 of 3 PIA Technical Standard TS-112 v1.0 Parachute Industry Association Publications September 2011 Harness/Container AAD Installation Test Protocol September 2011 TS-112 v1.0 2 of 3 SCOPE: The intent of TS-112 is to provide a recommended test matrix for any Harness/Conta

2、iner manufacturer (TSOA holder) to complete in order to authorize installations of specific AADs into their products. This series of 36 simulated best practice, mid range and worse case scenarios of rigging and malfunction possibilities is only a basic vehicle to accomplish primary confidence levels

3、 of interface between the AAD and the standard function of the TSOed components of the harness container system and reserve parachute. All tests should be done with full cooperation between the Harness/Container manufacturer and the AAD manufacturer. Completion of the TS-112 matrix by the Harness/Co

4、ntainer manufacturer in no way approves function of the AAD and is not intended to be used by the AAD manufacture to qualify/validate any AAD. Below is an outline of the test preparations and PASS/FAIL criteria. AAD Activation Test: 3 consecutive tests to pass with the same cutter configuration Prep

5、arations: All loops for testing must not be silicone treated All grommets must be free of any lubricant as oil or silicone, wipe off with isopropanol or equivalent Harness/Container straped to dummy, horizontal position on floor PASS/FAIL CRITERIA PASS 1 NO DELAY PASS 2 Slight delay (less than)0.25s

6、ec (failed) FAIL 2 Short launch of PC (less than) 50cm Bridle extraction (failed) FAIL 3 Container lock up ALL 36 TESTS MUST PASS September 2011 TS-112 v1.0 3 of 3 M o d e l S i z e S e r i a l # R e s P a r S i z e /T y p e M a i n S i z e /T y p eI d e a l /M F R R e c o m m e n d e d + . 7 5 “ /1

7、 9 m m + 1 “ /2 5 . 4 m m I d e a l /M F R R e c o m m e n d e d + . 7 5 “ /1 9 m m + 1 “ /2 5 . 4 m m1 1 1 1 1 12 2 2 2 2 23 3 3 3 3 3M o d e l S i z e S e r i a l # R e s P a r S i z e /T y p e M a i n S i z e /T y p eI d e a l /M F R R e c o m m e n d e d + . 7 5 “ /1 9 m m + 1 “ /2 5 . 4 m m I d

8、 e a l /M F R R e c o m m e n d e d + . 7 5 “ /1 9 m m + 1 “ /2 5 . 4 m m1 1 1 1 1 12 2 2 2 2 23 3 3 3 3 3M o d e l S i z e S e r i a l # R e s P a r S i z e /T y p e M a i n S i z e /T y p eI d e a l /M F R R e c o m m e n d e d + . 7 5 “ /1 9 m m + 1 “ /2 5 . 4 m m I d e a l /M F R R e c o m m e n

9、 d e d + . 7 5 “ /1 9 m m + 1 “ /2 5 . 4 m m1 1 1 1 1 12 2 2 2 2 23 3 3 3 3 3M o d e l S i z e S e r i a l # R e s P a r S i z e /T y p e M a i n S i z e /T y p eI d e a l /M F R R e c o m m e n d e d + . 7 5 “ /1 9 m m + 1 “ /2 5 . 4 m m I d e a l /M F R R e c o m m e n d e d + . 7 5 “ /1 9 m m + 1

10、 “ /2 5 . 4 m m1 1 1 1 1 12 2 2 2 2 23 3 3 3 3 3O PT I O N A L TES TT S- 1 1 2 H A R N E SS / C O N T A I N E R M A N U F A C T U R E R T E ST M A T R I XD a t e D a t e A A D P C L A U N C H F U L L M A I N C O N T A I N E RH / C MA N U F A C T U R E R LG M I D R A N G E MO D E L S I Z EH / C MA N

11、U F A C T U R E R S M M I D R A N G E MO D E L S I Z EH / C MA N U F A C T U R E R S M A L L E S T MO D E L S I Z ER EQ U I R ED TES TD a t e D a t e A A D P C L A U N C H E M P T Y M A I N C O N T A I N E RR EQ U I R ED TES TO PT I O N A L TES TA A D P C L A U N C H E M P T Y M A I N C O N T A I N

12、E RA A D P C L A U N C H E M P T Y M A I N C O N T A I N E RA A D P C L A U N C H E M P T Y M A I N C O N T A I N E RA A D P C L A U N C H F U L L M A I N C O N T A I N E RA A D P C L A U N C H F U L L M A I N C O N T A I N E RA A D P C L A U N C H F U L L M A I N C O N T A I N E RH / C MA N U F A C T U R E R L A R G E S T MO D E L S I Z E