NAVY UFGS-07 42 63-2011 FABRICATED WALL PANEL ASSEMBLIES《组合墙面板组件》.pdf

《NAVY UFGS-07 42 63-2011 FABRICATED WALL PANEL ASSEMBLIES《组合墙面板组件》.pdf》由会员分享，可在线阅读，更多相关《NAVY UFGS-07 42 63-2011 FABRICATED WALL PANEL ASSEMBLIES《组合墙面板组件》.pdf（25页珍藏版）》请在麦多课文档分享上搜索。

1、*USACE / NAVFAC / AFCESA / NASA UFGS-07 42 63 (May 2011)-Preparing Activity: NAVFAC SupersedingUFGS-07 42 63 (August 2010)UFGS-07 42 63 (January 2008)UFGS-07 40 00.00 40 (July 2007)UFGS-07 61 13.00 10 (July 2007)UNIFIED FACILITIES GUIDE SPECIFICATIONSReferences are in agreement with UMRL dated April

2、 2011*SECTION TABLE OF CONTENTSDIVISION 07 - THERMAL AND MOISTURE PROTECTIONSECTION 07 42 63FABRICATED WALL PANEL ASSEMBLIES05/11PART 1 GENERAL1.1 REFERENCES1.2 DEFINITIONS1.3 DESCRIPTION OF FABRICATED WALL PANEL ASSEMBLY SYSTEM1.3.1 Metal Wall Panel General Performance1.3.2 Structural Performance1.

3、3.3 Air Infiltration1.3.4 Water Penetration Under Static Pressure1.3.5 Water Penetration Under Dynamic Pressure1.4 SUBMITTALS1.5 QUALITY ASSURANCE1.5.1 Pre-Installation Conference1.5.2 Manufacturers Technical Representative1.5.3 Qualification of Manufacturer1.5.4 Qualification of Installer1.5.4.1 Qu

4、alifications for Welding Work1.5.5 Single Source1.5.6 Surface-Burning Characteristics1.5.7 Fire-Resistance Ratings1.5.8 Fabrication1.5.8.1 Sheet Metal Accessories1.5.9 Finishes1.5.10 Sustainable Design Certification1.6 DELIVERY, HANDLING, AND STORAGE1.7 PROJECT CONDITIONS1.8 WARRANTYPART 2 PRODUCTS2

5、.1 PANEL MATERIALS2.1.1 Aluminum Sheet2.1.2 Steel SheetSECTION 07 42 63 Page 1Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-2.1.3 Foam-Insulation Core Wall Panel2.1.4 Insulated Panel Construction2.1.5 Finish2.2 MISCELLANEOUS METAL FRAMING2.2.1 Gene

6、ral2.2.2 Fasteners for Miscellaneous Metal Framing2.3 FASTENERS2.3.1 General2.3.2 Exposed Fasteners2.3.3 Screws2.3.4 Rivets2.3.5 Attachment Clips2.4 ACCESSORIES2.4.1 General2.4.2 Rubber Closure Strips2.4.3 Metal Closure Strips2.4.4 Joint Sealants2.4.4.1 Sealants and Caulking2.4.4.2 Shop-Applied2.4.4

7、.3 Field-Applied2.4.4.4 Tape Sealant2.5 SHEET METAL FLASHING AND TRIM2.5.1 Fabrication2.6 REPAIR OF FINISH PROTECTIONPART 3 EXECUTION3.1 EXAMINATION3.2 PREPARATION3.3 WALL PANEL INSTALLATION3.4 FASTENER INSTALLATION3.5 FLASHING, TRIM AND CLOSURE INSTALLATION3.5.1 General Requirements3.5.2 Metal Flas

8、hing3.5.3 Closures3.6 WORKMANSHIP3.7 ACCEPTANCE PROVISIONS3.7.1 Erection Tolerances3.7.2 Leakage Tests3.7.3 Repairs to Finish3.7.4 Paint-Finish Metal Siding3.8 CLEAN-UP AND DISPOSAL- End of Section Table of Contents -SECTION 07 42 63 Page 2Provided by IHSNot for ResaleNo reproduction or networking p

9、ermitted without license from IHS-,-,-*USACE / NAVFAC / AFCESA / NASA UFGS-07 42 63 (May 2011)-Preparing Activity: NAVFAC SupersedingUFGS-07 42 63 (August 2010)UFGS-07 42 63 (January 2008)UFGS-07 40 00.00 40 (July 2007)UFGS-07 61 13.00 10 (July 2007)UNIFIED FACILITIES GUIDE SPECIFICATIONSReferences

10、are in agreement with UMRL dated April 2011*SECTION 07 42 63FABRICATED WALL PANEL ASSEMBLIES05/11*NOTE: This guide specification covers the requirements for both factory color and mill finish fabricated aluminum or steel structural metal wall panel assemblies.Adhere to UFC 1-300-02 Unified Facilitie

11、s Guide Specifications (UFGS) Format Standard when editing this guide specification or preparing new project specification sections. Edit this guide specification for project specific requirements by adding, deleting, or revising text. For bracketed items, choose applicable items(s) or insert approp

12、riate information.Remove information and requirements not required in respective project, whether or not brackets are present.Comments, suggestions and recommended changes for this guide specification are welcome and should be submitted as a Criteria Change Request (CCR).*NOTE: Coordinate this secti

13、on with other system components specifications such as framing, insulation and sheet metal flashing. Also coordinate with applicable Unified Facilities Criteria as it relates to the specific project.*PART 1 GENERAL1.1 REFERENCESThe publications listed below form a part of this specification to the e

14、xtent referenced. The publications are referred to within the text by the SECTION 07 42 63 Page 3Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-basic designation only.ALUMINUM ASSOCIATION (AA)AA ADM-105 (2005; Errata 2005) Aluminum Design ManualAA A

15、SD1 (2009) Aluminum Standards and DataAMERICAN ARCHITECTURAL MANUFACTURERS ASSOCIATION (AAMA)AAMA 501.1 (2005) Standard Test Method for Water Penetration of Windows, Curtain Walls and Doors Using Dynamic PressureAMERICAN INSTITUTE OF STEEL CONSTRUCTION (AISC)ANSI/AISC 341 (2005; Suppl No. 1 2005) Se

16、ismic Provisions for Structural Steel BuildingsAMERICAN IRON AND STEEL INSTITUTE (AISI)AISI S100 (2007; Supplement 1) North American Specification for the Design of Cold-Formed Steel Structural MembersAISI SG03-3 (2002; Suppl 2001-2004; R 2008) Cold-Formed Steel Design Manual SetAMERICAN SOCIETY OF

17、CIVIL ENGINEERS (ASCE)ASCE 7-10 (2010) Minimum Design Loads for Buildings and Other StructuresAMERICAN WELDING SOCIETY (AWS)AWS A5.1/A5.1M (2004) Specification for Carbon Steel Electrodes for Shielded Metal Arc WeldingAWS D1.1/D1.1M (2010) Structural Welding Code - SteelAWS D1.2/D1.2M (2008) Structu

18、ral Welding Code - AluminumASTM INTERNATIONAL (ASTM)ASTM A1008/A1008M (2010) Standard Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy and High-Strength Low-Alloy with Improved Formability, Solution Hardened, and Bake HardenedASTM A123/A123M (2009) Standard Sp

19、ecification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel ProductsASTM A36/A36M (2008) Standard Specification for Carbon Structural SteelASTM A424/A424M (2009a) Standard Specification for Steel Sheet for Porcelain EnamelingSECTION 07 42 63 Page 4Provided by IHSNot for ResaleNo reproductio

20、n or networking permitted without license from IHS-,-,-ASTM A463/A463M (2010) Standard Specification for Steel Sheet, Aluminum-Coated, by the Hot-Dip ProcessASTM A606/A606M (2009a) Standard Specification for Steel Sheet and Strip, High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled, with Improved A

21、tmospheric Corrosion ResistanceASTM A653/A653M (2010) Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip ProcessASTM A755/A755M (2003; R 2008) Standard Specification for Steel Sheet, Metallic Coated by the Hot-Dip Process and Prep

22、ainted by the Coil-Coating Process for Exterior Exposed Building ProductsASTM A780/A780M (2009) Standard Practice for Repair of Damaged and Uncoated Areas of Hot-Dip Galvanized CoatingsASTM A792/A792M (2010) Standard Specification for Steel Sheet, 55% Aluminum-Zinc Alloy-Coated by the Hot-Dip Proces

23、sASTM A924/A924M (2010a) Standard Specification for General Requirements for Steel Sheet, Metallic-Coated by the Hot-Dip ProcessASTM B 117 (2009) Standing Practice for Operating Salt Spray (Fog) ApparatusASTM B 209 (2007) Standard Specification for Aluminum and Aluminum-Alloy Sheet and PlateASTM B 2

24、09M (2007) Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate (Metric)ASTM C 273/C 273M (2007a) Shear Properties of Sandwich Core MaterialsASTM C 286 (1999; R 2009) Standard Terminology Relating to Porcelain Enamel and Ceramic-Metal SystemsASTM C 553 (2008) Standard Specification

25、 for Mineral Fiber Blanket Thermal Insulation for Commercial and Industrial ApplicationsASTM C 612 (2010) Mineral Fiber Block and Board Thermal InsulationASTM C 920 (2011) Standard Specification for Elastomeric Joint SealantsSECTION 07 42 63 Page 5Provided by IHSNot for ResaleNo reproduction or netw

26、orking permitted without license from IHS-,-,-ASTM D 1056 (2007) Standard Specification for Flexible Cellular Materials - Sponge or Expanded RubberASTM D 1308 (2002; R 2007) Effect of Household Chemicals on Clear and Pigmented Organic FinishesASTM D 1621 (2010) Compressive Properties of Rigid Cellul

27、ar PlasticsASTM D 1622 (2008) Apparent Density of Rigid Cellular PlasticsASTM D 1667 (2005) Flexible Cellular Materials - Poly (Vinyl Chloride) Foam (Closed-Cell)ASTM D 2244 (2009b) Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color CoordinatesASTM D 2247 (2010)

28、 Testing Water Resistance of Coatings in 100% Relative HumidityASTM D 2794 (1993; R 2010) Resistance of Organic Coatings to the Effects of Rapid Deformation (Impact)ASTM D 3363 (2005) Film Hardness by Pencil TestASTM D 4214 (2007) Standard Test Method for Evaluating the Degree of Chalking of Exterio

29、r Paint FilmsASTM D 522 (1993a; R 2008) Mandrel Bend Test of Attached Organic CoatingsASTM D 523 (2008) Standard Test Method for Specular GlossASTM D 6226 (2010) Standard Test Method for Open Cell Content of Rigid Cellular PlasticsASTM D 714 (2002; R 2009) Evaluating Degree of Blistering of PaintsAS

30、TM D 822 (2001; R 2006) Filtered Open-Flame Carbon-Arc Exposures of Paint and Related CoatingsASTM D 968 (2005; R 2010) Abrasion Resistance of Organic Coatings by Falling AbrasiveASTM E 119 (2010b) Standard Test Methods for Fire Tests of Building Construction and MaterialsASTM E 136 (2011) Behavior

31、of Materials in a Vertical Tube Furnace at 750 Degrees CSECTION 07 42 63 Page 6Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-ASTM E 1592 (2005) Structural Performance of Sheet Metal Roof and Siding Systems by Uniform Static Air Pressure DifferenceA

32、STM E 283 (2004) Determining the Rate of Air Leakage Through Exterior Windows, Curtain Walls, and Doors Under Specified Pressure Differences Across the SpecimenASTM E 331 (2000; R 2009) Water Penetration of Exterior Windows, Skylights, Doors, and Curtain Walls by Uniform Static Air Pressure Differen

33、ceASTM E 84 (2010b) Standard Test Method for Surface Burning Characteristics of Building MaterialsASTM G 152 (2006) Operating Open Flame Carbon Arc Light Apparatus for Exposure of Nonmetallic MaterialsASTM G 153 (2004; R 2010) Operating Enclosed Carbon Arc Light Apparatus for Exposure of Nonmetallic

34、 MaterialsGREENGUARD ENVIRONMENTAL INSTITUTE (GEI)GEI Greenguard Standards for Low Emitting ProductsMETAL BUILDING MANUFACTURERS ASSOCIATION (MBMA)MBMA MBSM (2002) Metal Building Systems ManualNATIONAL ASSOCIATION OF ARCHITECTURAL METAL MANUFACTURERS (NAAMM)NAAMM AMP 500 (2006) Metal Finishes Manual

35、PORCELAIN ENAMEL INSTITUTE (PEI)PEI 1001 (1996) Specification for Architectural Porcelain Enamel (ALS-100)PEI CG-3 (2005) Color Guide for Architectural Porcelain EnamelSCIENTIFIC CERTIFICATION SYSTEMS (SCS)SCS Scientific Certification Systems (SCS)Indoor AdvantageSHEET METAL AND AIR CONDITIONING CON

36、TRACTORS NATIONAL ASSOCIATION (SMACNA)SMACNA 1793 (2003) Architectural Sheet Metal Manual, 6th EditionSECTION 07 42 63 Page 7Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-UNDERWRITERS LABORATORIES (UL)UL 580 (2006; Reprint Jul 2009) Tests for Uplif

37、t Resistance of Roof AssembliesUL Bld Mat Dir (2011) Building Materials Directory1.2 DEFINITIONSFabricated Wall Panel Assembly: Metal wall and liner panels, attachment system components, miscellaneous metal framing, thermal insulation, and accessories shop fabricated or field assembled for a complet

38、e weather-tight wall system.1.3 DESCRIPTION OF FABRICATED WALL PANEL ASSEMBLY SYSTEM*NOTE: Coordinate with Part 2 materials specification.In the first sentence, select finish type, metal type, attachment type and delete other options.In the second sentence, select a combination of options as necessa

39、ry to describe the generic profile required. Include the last bracketed option of the second sentence when generic profile is shown on drawings. Show panel profile, cross-section, and dimensions on the drawings when a particular aesthetic appearance is desired.*Factory color finished,Mill finish gal

40、vanized galvalume aluminum metal wall panel system with concealed fasteningexposed fastener attachment. Panel profile must be embossedrecessed seam lockflush facesmooth facerecessed beadraised beadstriatedsquare ribbedbeaded ribroll lock seamsnap lock seambox ribcorrugatedstanding seambatten seam an

41、d with stiffening ribs in the flat of the panelas shown on drawings. Interior finish of panel assembly to be _.1.3.1 Metal Wall Panel General PerformanceComply with performance requirements, conforming to AISI S100, without failure due to defective manufacture, fabrication, installation, or other de

42、fects in construction. Wall panels and accessory components must conform to the following standards:ASTM A1008/A1008MASTM A123/A123MASTM A36/A36M ASTM A424/A424M, ASTM C 286, PEI 1001, PEI CG-3 for Porcelain and Ceramic Enameling ASTM A653/A653M ASTM A463/A463M for aluminum coated steel sheet ASTM A

43、606/A606M ASTM A755/A755M for metallic coated steel sheet for exterior coil pre-painted applications. ASTM A780/A780M for repair of damage or uncoated areas of hot-dipped SECTION 07 42 63 Page 8Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-galvaniz

44、ed coating. ASTM A924/A924M for metallic coated steel sheet ASTM C 273/C 273MASTM D 522 for applied coatingsUL Bld Mat Dir1.3.2 Structural PerformanceMaximum calculated fiber stress must not exceed the allowable value in the AISI or AA manuals; a one third overstress for wind is allowed. Midspan def

45、lection under maximum design loads is limited to L/180. Contract drawings show the design wind loads and the extent and general assembly details of the metal siding. Contractor must provide design for members and connections not shown on the drawings. Siding panels and accessories must be the produc

46、ts of the same manufacturer.Provide metal wall panel assemblies complying with the load and stress requirements in accordance with ASTM E 1592. Wind Load force due to wind action governs the design for panels.Wall systems and attachments are to resist the wind loads as determined by UL 580 and ASCE 7-10 in