NAVY MIL-L-714 G-1988 LEGGINGS MEN-S《男式绑腿》.pdf

《NAVY MIL-L-714 G-1988 LEGGINGS MEN-S《男式绑腿》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-L-714 G-1988 LEGGINGS MEN-S《男式绑腿》.pdf（23页珍藏版）》请在麦多课文档分享上搜索。

1、P. *- MIL-L-71LIG BLI 7779706 0371L157 L m MIL-L-714G 30 November 1988 SUPERSEDING 27 June 198G MIGL-714F MILITARY SPECIFICATION LEGGINGS, MENS This specification is approved for use by the Navy Clothing and Textile Research Facility, Department of the Navy, and is available for use by all Departmen

2、ts and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers the requirements for one typc of mens leggings, fabricated from cotton duck cloth. 1.2 Classification. The leggings shall be procured in the following sizes as specified (see 6.2): L 2. APPLICABLE DXUMENTS 2.

3、1.1 Specifications, standards, and handbooks. The f olloving specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of taese documents shall be those listed in the issue of the Department of Defmse Index of Specifi

4、cations and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). Beneficial comments (recommendations, additions, deletions) and any pertilent data which may be of use in improving this document should be addressed to: Officer in Charge, Navy Clothing and Textile Research

5、Facility, 21 Strathaore Road, Natick, MA 01760-2490 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of chis document or by letter. WC N/ FSC 8414.0 DISTRIBUTION STATEMENT A. Approved for public release, distribution is unlimited. THIS DOC

6、UMENT CONTAINS 83 PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- - _- MIL-L-714G 84 W 777770b 03714b0 i W SPECIFICATIONS FEDERAL V-T-2 8 5 * NN-P-71 ccc-c-419 ccc-D-950 DDD-L-20 MI LI TARY MI L-L-396 MIL-F-49 5 MIL-C-496 MI L-W- 5 3 O * MIL-

7、P-15011 MIL-B-17757 MIL-T-43566 MIL-L-714G - Thread, Polyester - Pallet, Material Handling, Wood, Stringer - Cloth, Duck, Cotton, Unbleached, Plied-Yarns Army - Dyeing and Aftertreatment Processes for Cotton - Label; for Clothing, Equipage, and Tentage (General Construction, 2 way and 4 Way (Partial

8、) and Numbered Cloths Use ) - Laces, Leggings - Finish, Chemical, Black, for Copper Alloys - Clips, End, Strap - Webbing, Textile, Cotton, General Purpose Natural , or in Colors - Pallet, Material Handling, Wood, Post Construction, 4 Way Entry - Boxes, Shipping, Fiberboard (Modular Sizes) - Tape, Te

9、xtile, Cotton, General Purpose, Natural or in Colors STANDARDS FEDERAL FED-STD-751 - Stitches, Seams, and Stitchings MI LI TARY MI L-STD-1 O 5 - Sampling Procedures and Tables for Inspection by MI L-STD-129 - Marking for Shipment and Storage Attributes * MIL-STD-147 - Palletized Unit Loads (Copies o

10、f the Federal Information Processing Standard (FIPS) are available to Department of Defense activities from the Commanding Officer, Naval Publications and Forms Center, (Am: NPODS), 5801 Tabor Avenue, Philadelphia, PA 19120-5099. Others must request copies of FIPS from National Technical Information

11、 Service, 5285 Port Royal Road, Springfield, VA 22161-2171.) 2.1.2 Other Government documents, drawings, and publications. The following other Government documents, drawings, and publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues are thos

12、e cited in the solicitation. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- 5 MIL-L-7L4G 84 = 9999906 037LgbL T - - . I l MIGG714G LAWS AND REGULATIONS U.S. POSTAL SERVICE MANAL (Copies of the manual may be obtained from the Superintendent of Doc

13、uments, U.S. Government Printing Office, Washington, D.C. 20402-0001) * 2.2 Non-Government publications. The following document(s) form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DOD adopted shall be those isted in the is

14、sue of the DODISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS are the issues of the documents cited in the solicitation (see 6.2). NATIONAL MOTOR FREIGHT TRAFFIC ASSOCIATION, INC., AGENT National Motor Freight Classification (Application fo

15、r copies should be addressed to the American Trucking Association, AT“: Traffic Department, 1616 P Street, N.W., Washington, DC 20036-1404). UNIFORM CLASSIFICATION COMMITTEE, AGENT Uniform Freight Classification (Application for copies should be addressed to the Uniform Classification Codttee, Room

16、116, 222 South Riverside Plaza, Chicago, Illinois 60606-5808). (Non-Government standards and other publications are normally available from the organizations that prepare or distribute the documents. These documents also may be available in or through libraries or other informational services.) 2.3

17、Order of precedence. In the event of a conflict between the text of this document and the references cited herein (except for related associated detail specifications, specification sheets, or MS standards) the text of this document takes precedence. Nothing in this document, however, supersedes app

18、licable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Guide s Samples, when furnished, are solely for guidance and information +- to e contractor (see 6.3). Variations from this specification may appear in the sample in which case this specification shall go

19、vern. 3.2 First article. when specified, the contractor shall furnish sample unit(s) for first article inspection and approval (see 4.3 and 6.2). 3,3 Material. * 3.3.1 Base cloth. The basic cloth for the leggings shall be .cotton duck, conforming to type I, hard texture, No. 6 or No. 8, of CCC-C-419

20、. Selvage stripes are not permitted. The cloth shall be bleached white, conforming to type V, class C, of CCC-I)-950. The whiteness of the bleached duck shall approximate the whiteness of the component parts of 3.3.2, 3.3.3, and 3.3.4. 3 Provided by IHSNot for ResaleNo reproduction or networking per

21、mitted without license from IHS-,-,-MIL-L-714G 3.3.2 Webbin . The webbing used for the footstrap on the leggings shall be cotton, 5/ T+! inc in width, conforming to type III, class 2, of MIL-W-530. . The tape used for binding the top and bottom edges of the leggings 303e3 s FE a be cotton, 3/4 inch

22、in width, conforming to type I, class 2, of MIL-T-43566. 3.3.4 Laces, le in s. The laces shall be cotton, conforming to MIL-L-396 and shall eches long. 3.3.5 Thread. The thread used for seaming and stitching the leggings shall be polyester, conforming to type I or II, class 1, subclass A, sizes B an

23、d E, of V-T-285. The color shall approximate the whiteness of the base cloth (see 3.3.1) and component parts (see 3.3.2, 3.3.3 and 3.3.4). 3.3.6 Hardware. 3.3.6.1 Lacing eyelet and neck washer. The lacing eyelet and neck washer shall be made of brass and shall h ave a black finish in accordance .wit

24、h 3.3.6.7. The lacing eyelet shall conform to part No. A 1396 or equal and the neck washer shall conform to part No. A 1365 or equal (see 6.4 and 6.5). 3.3.6.2 Lacinq hook and washer. The lacing hook and washer shall be nade of brass ana shall have a black finish in accordance with 3.3.6.7. The lasi

25、ng hook shall conform to part No. 2024 or equal and the washer shall conform to part No. A 1128 or equal (see 6.4 and 6.5). 3.3.6.3 Buckle. The buckle shall be made of brass and shall have a black finish in acnce with 3.3.6.7. The buckle shall conform to part No. 03745 or equal (see 6.4 and 6.5). 3.

26、3.6.4 Buckle cli . The buckle clip shall be made of brass and shall _?ave a black finis + in accordance with 3.3.6.7. The buckle clip shall confonii to part No. D 3219 OR equal (see 6.4 and 6.5). The buckle clip securing eyelet shall be made of brass and shall h ave a black finish in accordance with

27、 3.3.6.7. The component part shall conform to part No. A 1404 or equal (see 6.4 and 6.5). The end clip used on the footstrap of the leggings shall conform to type I, class 1, size 5/8 inch, of MIL-C-496 and lacquer or clear epoxy resin coated. * 3.3.6.7 Hardware finish. The finish shall be black che

28、mical finish in accordance with MIL-F-495 and lacquer or clear epoxy resin coated. As an alternate, the finish may be black enamel finish with a minmum of two coats. * 3.3.7 Label. Each legging shall be marked with a combination size, identification and instruction label conforming to type III or IV

29、, class 14, of DDD-L-20, except that the height of characters indicating the size shall be a minimum of 3/4 inch solid or open print type. The label shall show colorfastness to laundering and crocking, and shall bear the follosing inscription: 3.3.6.5 Buckle clip securing eyelet. 3.3.6.6 End clip. 7

30、 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-L-734G 84 M 0b 0373463 3 LEGGINGS, MENS (100% COTTON) CONTRACT No. DJLA 100-00-0-0000 (example) STOCK No. 8440-00-000-0000 (example) SIZE: 4 (example) NAME OF CONTRACTOR: NAME OF MFG: (If other

31、than contractor) ?ANDWMH 1. Soak in warm water and soap or synthetic detergent - 5 minutes. 2. Wash leggings by rubbing together. 3. Rinse thoroughly with warm water. 4. Hang dry. 1. 2. Hang dry. MACHINE WASH Machine wash warm, delicate cycle using soap or synthetic detergent. The leggings shall be

32、of a three piece, fitted style bottom edges, fitted with a foot strap and buckle, and having and outside hook and eyelet lacing closure (see figure 1). 3.4.1 Figure. Figure 1 is furnished for information purposes only. To the extent of any inconsistencies between the written specification and the fi

33、gure, the written specification shall govern. 0 * 3.5 Patterns. Standard patterns provide 1/2 inch seam allowance for double-lapped and double-stitched seams. Standard patterns to be used to cut working patterns will be furnished by the Government (see 6.3). The working patterns shall be identical t

34、o the Government patterns. Neither the Government patterns nor the working patterns shall be altered in any way, except that additional notches for use during construction are permitted on the working patterns. left and one right), bound with tape along the top and 3.5.1 Pattern arts. The component

35、parts for each pair of leggings (one right andehall be cut from the basic material specified in 3.3.1 and in accordance with the following pattern parts required for the manufacturing process: Pattern parts Cut parts Front Side Back 2 2 2 3.6 Construction. 5 Provided by IHSNot for ResaleNo reproduct

36、ion or networking permitted without license from IHS-,-,-_ I_- MIL-L-714G 8i.I H 7777906 0371464 5 M MILL-71 4G * 3.6.1 Stitches, seams and stitchings. Stitch, seam and stitching types specified in Table I shall conform to FED-STD-751. Whenever two or more methods for seam or stitch types are given

37、for the same part of the operation any one may be used. Seam allowance shall be maintained with seams sewn so that no raw edges, runoffs, twists, pleats, puckers or open seams result. All seams shall start and finish evenly. Thread tension shall be maintained so that there is no tight or loose stitc

38、hing. Where stitch type 401 is used, the looper (underthread) shall be on the inside of the leggings. Top stitching and edge stitching shall be 1/16 to 1/8 inch from the edge, The gage for double-lapped and double-stitched seams shall be 1/4 to 5/16 inch. End of all seams and stitching when not caug

39、ht in other seams or stitching shall be backtacked not less than 1/4 inch. The ends of a continuous line of stitching shall be overlapped not less than 1/2 inch. Thread breaks (all stitch type) shall be repaired by stitching back of the break not less than 1/2 inch. Skipped stitches or thread breaks

40、 on 401 stitch type may be repaired by using 301 stitch type. When ends of overedge stitching are not caught in other seams or stitching, the ends shall be tacked. 3.6.2 Thread breaks and end of seams. 3.6.3 Stitches per inch. The minimum and maximum number of stitches per inch shall be as specified

41、 in Table I. * 3.7 Manufacturing operation requirements. The leggings shall be manufactured in accordance with the operation requirements specified in Table I. The contractor is not required to-follow the-exact sequence of operations listed provided that the finished leggings are identical to that p

42、roduced by following the sequence of operations as listed in Table I. * 3.7.1 Size markin . The component parts of leggings shall be marked, ticketed or 40 insure uniform size throughout the leggings. Any method may be used except: (1) Metal fastening devices. (2) Sew-on size tickets. (3) Adhesive t

43、ype tickets which discolor or adhere to the material upon removal of tickets. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I .- - I NIL-L-714G 4 3993906 03714b5 7 MIL-L-714G 3.7.3 Abbreviations in table of operations. The abbeviations used in ta

44、ble i are as follows: Stch - in - Ndl - Bob - LPr Mchne - Brtck - Comrcl - smr - Btnhl - incl - dbl - - Stitch inch Needle Bobbin Looper Machine Bartack Commercial similar Buttonhole including double 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-

45、 MIL-L-714G 84 9979906 03714bb 9 MIL-L-714G , TABLE I - CONSTRUCTION OF LEGGINGS Thread No. Opera ti on Stch sew Stch Ndl Bob/ Type Stch type in Lpr 1. 2. 3. 4. 5. Cutting a. Cut the leggings in strict accordance with the patterns furnished which show size, shape, directional lines, and notches for

46、proper assembly of all cut parts. b. piece of material. All component parts shall be cut from one Replacement of defective components Durinq the spreadinq, cuttinq, and manufactuiing process, components - having material defects or damages that are classified as defects in Section 4, shall be remove

47、d from production and replaced with nondefective and properly matched components. ti zeMm; r k ing ticketed as indicated in 3.7.1. parts shall be marked, bundled, or Attach front and back pieces to side piece a. Join front and back pieces to side piece with a double-lapped, double-stitched seam, so

48、that the front and back overlap the side piece b. Bind the top and bottom edges with a strip of tape (see 3.3.3), with the stitching 1/16 to 3/32 inch from the bottom edge of binding. F-Y Were ge outer edge of front piece (not required if selvage is used). b. Turn edge of front piece to inside of le

49、ggings to form a 7/8 (+1/8) inch hem, and stitch 11/16 (+1/16) - in . a. Trim all thread ends. 14. Cleaniy. b. Remove all loose threads-. C. Remove all spots and stains 11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-.- - _ MIL-L-714G 4 W 777790b 0371470 O 9 3.9 Measurements. The sizes and measurements of the finished leggings shall conform to th