NAVISTAR MPAPS K-6929-2014 Mounting Tapes - Parts 1 & 2.pdf

《NAVISTAR MPAPS K-6929-2014 Mounting Tapes - Parts 1 & 2.pdf》由会员分享，可在线阅读，更多相关《NAVISTAR MPAPS K-6929-2014 Mounting Tapes - Parts 1 & 2.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2014 by Navistar, Inc. DECEMBER 2014 Page 1 of 14 NAVISTAR, INC. Material, Parts, and Process Specificati

2、ons (MPAPS) NUMBER: MPAPS K-6929 Former Designation: TMS-6929 TITLE: Mounting Tapes Parts 1 & 2 CURRENT REV No.: 1412 DATE: Dec. 2014 WRITTEN/EDITED BY: Materials Engineering APPROVED BY: Materials Engineering SUPERSEDES: Rev. 1402 Feb. 2014 PRINTED COPIES OF THIS DOCUMENT MUST BE VERIFIED FOR CURRE

3、NT REVISION This specification may involve hazardous materials, equipment, and procedures. This specification does not purport to address all of the safety issues associated with its use. The user is responsible to consult appropriate safety and health practices and to determine the applicability of

4、 regulatory limits prior to use. Change Notice: Added approved adhesives/suppliers, editorial changes. Part 1 General, Property, and Performance Requirements 1.0 APPLICATION Part 1 of this specification covers mounting tape adhesive systems, adhesive transfer tapes and pre-applied pressure sensitive

5、 adhesives (PSA) used for bonding parts in the construction of truck and tractor cabs and components. Part 2 covers the production process requirements for these types of bonding systems. 2.0 SCOPE Part 1 of this specification covers the material properties, performance requirements, production qual

6、ity and process control, suppliers responsibility, source approval and quality control, general information, and sources for approved adhesive systems. 2.1 Restricted Chemical Substances Effective January 1, 2007, all product supplied to the requirements of this specification must comply with the re

7、quirements of the MPAPS B-50 specification. 3.0 REFERENCE DOCUMENTS Unless otherwise specified, the latest issue of all referenced standards shall apply. The following Specifications, Standards, and Regulations are referenced in this specification. Quality System Standard ISO 9001 or TS-16949 CFR Ti

8、tle 29, Part 1910 NAVISTAR TMS-4114 NAVISTAR TMS-7051 ASTM D 2919 ASTM D 2979 NAVISTAR Manufacturing Std. MS-D-13 NAVISTAR TMS-7133 ASTM D 3163 NAVISTAR Engineering Design Std A-16 NAVISTAR MPAPS G-9009 ASTM D 3330 NAVISTAR MPAPS B-50 NAVISTAR TMS-9522 ASTM D 3654 NAVISTAR MPAPS A-6 NAVISTAR MPAPS P

9、-9543 ASTM D 5041 NAVISTAR MPAPS C-10 ASTM B 117 SAE J243 NAVISTAR MPAPS D-22 ASTM D 1002 SAE J1523 NAVISTAR MPAPS D-28 ASTM D 1056 SAE J1525 NAVISTAR MPAPS G-5 ASTM D 1600 SAE J1553 NAVISTAR CEMS GT-7E ASTM D 1667 NAVISTAR TMS-4102 ASTM D 2240 NAVISTAR TMS-4103 NAVISTAR MPAPS G-19 Part I ASTM D 229

10、4 NUMBER: MPAPS K-6929 TITLE: Mounting Tapes Parts 1 & 2 REVISION: 1412 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2014 by Navistar, Inc. DECEMBER 2

11、014 Page 2 of 14 4.0 REQUIREMENTS Adhesive materials supplied to this specification shall bond the intended substrates (see Table 2 for listed substrates, this is not intended to be an exhaustive list or define all materials that should be tested) to produce a permanent bond. The general properties

12、of as received tape materials are indicated in Table 3. Adhesive materials supplied to this specification must be compatible with all subsequent cleaning and paint operations used in the Assembly Plant and with the current production materials for which the new adhesive system approval is sought. It

13、 is the responsibility of the supplier to insure compatibility of new materials with the Assembly Plants currently used materials and processes and to obtain approval from the Production Process Manager of the Assembly Plant for the use of new adhesive materials. Clarification: This specification sh

14、ould be viewed as a Design Requirements Document Template or Test Plan Template for applications using a PSA type bonding system. As this is intended to cover all types of these applications, the test requirements and the “general expected values” in Table 1 are guidelines rather than hard limits fo

15、r all applications. In all cases, it is the discretion of Navistar Materials Engineering group as to which requirements are pertinent to the application. The process should follow these steps: 1. Engineering reviews a PSA application with Materials Engineering and releases prints referencing this sp

16、ecification if the application is appropriate and Materials Engineering concurs. 2. Supplier submits and reviews a test plan to this specification with guidance from Materials Engineering and other appropriate groups at Navistar. 3. The test plan may be approved or modified. Once accepted, the suppl

17、ier shall commence testing to the approved plan. 4. Upon test completion, the report is submitted to Materials Engineering and reviewed with other groups as necessary. 5. If the results are deemed acceptable, a report documenting approval of that application with those specific materials will be iss

18、ued by Materials Engineering. 6. On a future revision of this specification, that report number and pertinent information will be listed in Table 4 if appropriate. 4.1 General Properties Properties described are for reference. Property values will be reported on all newly submitted test reports and

19、will be added into Table 3 when the adhesive system receives final approval. 4.1.1 Material The polymer base for the foam carrier and adhesive shall be described using terminology consistent with ASTM D1600. 4.1.2 Tack ASTM D 2979 shall be used to measure the tack of an adhesive. The adhesive shall

20、be categorized or described as high, medium, or low tack. 4.1.3 Foam Carrier The foam properties shall be measured and reported in accordance with ASTM D 1056. 4.1.4 Release Liner The release liner will be either a moisture resistant coated paper or a polyethylene film. The force to release the line

21、r shall not exceed 0.05 N/mm for paper liner or 0.09 N/mm for polyethylene, as measured by ASTM D 3330, 180 peel at 300 mm/min. 4.1.5 Density Density of the adhesive and foam carrier will be measured and reported per ASTM D 1667. Note: Requirements related to the foam carrier are not applicable to a

22、dhesive transfer tapes or pre-applied PSA. NUMBER: MPAPS K-6929 TITLE: Mounting Tapes Parts 1 & 2 REVISION: 1412 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent lia

23、bility. 2014 by Navistar, Inc. DECEMBER 2014 Page 3 of 14 4.2 Sample Preparation A minimum of five samples will be prepared for each condition tested. The surface condition tested should be representative of production conditions and must be fully described in the test report. The bond overlap for l

24、ap shear tests shall be 25 mm x 25 mm (1 inch x 1 inch). Peel specimens may typically use a 25 mm by 150 mm strip with a 25 mm tab at one end, as appropriate. The geometry for each test may vary as necessary to comply with the specified test methods. Test specimens must be fully described in the rep

25、ort. The adhesive application conditions (applied pressure, dwell time, and temperature) should match the production conditions as closely as possible and must be described fully in the test report. The application conditions used for qualification testing must be reproducible for subsequent laborat

26、ory and production process testing. All samples shall be conditioned for 72 hours at ambient lab conditions prior to testing or exposures. Report both the load and failure mode for each sample. Summarize test data with the average values and standard deviation including all samples. Any discarded te

27、st samples will be included in the report and reasons for discarding the test explained. Note: There are obvious cases when it is not appropriate to use both actual adherends for a test. It may be necessary and proper to use separate samples made with a dummy adherend to drive the test of the actual

28、 surface interface that it is desired to test. Please consult with Materials Engineering prior to test if it is felt that this is necessary and describe completely in the final report. Example: A foam mounting tape is being used to bond a rigid plastic part to a steel reinforcement. It would be pref

29、erred to use a foil dummy adherend to perform peel tests to each surface. The actual surface tested is the foam to adherend, not the foil to foam. By making this substitution, an accurate assessment of the bond surface in peel can be made. 4.3 Property And Performance Requirements The requirements f

30、or the following shear and peel tests are listed in Tables 1A and 1B. 4.3.1 Lap Shear Strength 4.3.1.1 Method: Prepare samples as directed in Section 4.2. Test per ASTM D 3163 or ASTM D 1002, as appropriate. Tensile machine jaw separation rate shall be 13 mm (.5 in) per minute. Test overlap shear at

31、 the temperatures specified in Table 1A after holding at that temperature for 30 minutes. 4.3.2 Peel Adhesion 4.3.2.1 Method: ASTM D 3330 test method, except that the substrate shall be appropriate to the application and that the peel backing should be 0.127 mm (0.005 inch) thick anodized aluminum f

32、oil. Tests will be performed on samples prepared as directed in Section 4.2, except for the geometry requirements of the test. Perform a 90 peel at 300 mm/min. Test peel at the temperatures specified in Table 1B after holding at that temperature for 30 minutes. 4.3.3 Stress Durability 4.3.3.1 Method

33、: Test per ASTM D 2919 or ASTM D 3654 using a fixture described in ASTM D 2294, ASTM D 2919, or ASTM D 3654. Prepare samples as indicated in Section 4.2, Sample Preparation, except for the geometry requirements of the fixture used. Load shear samples to 750 grams per 25 mm by 25 mm overlap. Load pee

34、l samples to 250 grams per 25 mm sample width. Expose separate sets of samples to 500 hours heat aging at 70 2C and 500 hours at 100% relative humidity at 35 2C. 4.3.3.2 Required: Samples shall remain intact with no more than 2 mm of creep. Samples shall be tested for residual strength as in 4.3.1,

35、Lap Shear Strength, or 4.3.3, Peel Adhesion. Report test values. NUMBER: MPAPS K-6929 TITLE: Mounting Tapes Parts 1 & 2 REVISION: 1412 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to

36、 assume all patent liability. 2014 by Navistar, Inc. DECEMBER 2014 Page 4 of 14 4.3.4 Corrosion 4.3.4.1 Method: Test per ASTM B 117 for 500 hours on coupons prepared as per Section 4.2. Samples shall be tested as in Section 4.3.1 for residual strength and test values reported. 4.3.5 Humidity 4.3.5.1

37、 Method: Test per CEMS GT-7E for 500 hours on unstressed coupons prepared per Section 4.2. Samples shall be tested as in Section 4.3.1 and 4.3.2, Peel Adhesion, as applicable, for residual strength and test values reported. 4.3.6 Water Immersion 4.3.6.1 Method: Immerse unstressed specimens in distil

38、led water at 25C 2C for 500 hours. Samples shall be tested as in 4.3.1, Lap Shear, and 4.3.2, Peel Adhesion, as applicable. Report residual strength values. This test may be modified to 168 hour exposure for a “screen” evaluation as defined in Table 1. 4.3.7 Shrinkage 4.3.7.1 Method: Apply a 170 mm

39、piece of the product to a 150 mm steel panel and trim evenly at the edge of the panel. Bake the assembly at 70C for 48 hours. Remove, allow panels to cool, and examine for shrinkage. 4.3.7.2 Required: Shall show no more than 0.5% shrinkage. 4.3.8 Heat Age 4.3.8.1 Method: Expose unstressed specimens

40、to 90C 2C for 500hrs. Samples shall be tested as in 4.3.1, Lap Shear, and 4.3.2, Peel Adhesion, as applicable. Report residual strength values. This test may be modified to 168 hour exposure for a “screen” evaluation as defined in Table 1. 5.0 QUALITY All material produced to this specification shal

41、l be clean and free of dirt, grease, and contamination. All debris from cutting and processing shall be removed. Parts shall be free of voids, cuts or tears. 5.1 Qualification Material and processes submitted for approval to this specification shall include the following: 5.1.1. A detailed, signed t

42、est report as per MPAPS P-9543, documenting testing to this specification. 5.1.2. Test coupons or photographs showing failure modes for each test. 5.1.3. The complete procedure used for preparing and curing materials for test, especially surface preparation and condition of the test coupons. 5.1.4.

43、Adhesive, substrate and any chemicals used for bonding. 5.2 Submission The material and test report shall be submitted to: Manager of Non-Metallic Materials, Materials Engineering and Technology, Navistar, Inc., 10400 West North Avenue, Melrose Park, IL 60160. 5.3 Approval A report from Navistar, In

44、c. will be issued approving material to this specification. Approval is not formally granted until this report has been published. A change to this Specification listing the new approval may be delayed. The approval report serves as authorization for the use of that adhesive system prior to the chan

45、ges to this specification. 6.0 QUALIFICATION Engineering qualification of sources is required in advance of production shipments. Suppliers shall submit samples for approval of finish, luster, color and appearance to the Navistar Industrial Design NUMBER: MPAPS K-6929 TITLE: Mounting Tapes Parts 1 &

46、 2 REVISION: 1412 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2014 by Navistar, Inc. DECEMBER 2014 Page 5 of 14 Group. Samples shall be accompanied b

47、y test data certifying that all requirements of the specification have been met. Upon approval, styling master samples denoting the minimum level of acceptable appearance quality shall be developed and retained by the supplier and the quality department of each using NAVISTAR facility. 6.1 Quality C

48、ontrol Plan A Quality Control Plan for products supplied to the requirements of this specification will be established by mutual agreement between NAVISTAR and the supplier. Unless specific exception is noted, the following characteristics, where applicable*, shall be included in the plan as feature

49、s for management by statistical process control.* * Other characteristics for inclusion in the control plan may be specified on the engineering drawing and/or purchase order. * See NAVISTAR Engineering Design Standard A-16 7.0 SOURCE APPROVAL AND QUALITY CONTROL 7.1 Supplier Requirements All suppliers to NAVISTAR are required to be registered to ISO 9001 Quality System Requirements. NAVISTAR will also accept TS-16949 registrat