GSA A-A-3050-1996 VISE PIPE HINGED JAW《管子台虎钳》.pdf

《GSA A-A-3050-1996 VISE PIPE HINGED JAW《管子台虎钳》.pdf》由会员分享，可在线阅读，更多相关《GSA A-A-3050-1996 VISE PIPE HINGED JAW《管子台虎钳》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、A-A-3050 m 9999974 0372755 532 rn INCH-POUND A-A-3050 November6.1996 COMMERCIAL ITEM DESCRIPTION VISE, PIPE, HINGED JAW The General Services Administration has authorized the use of this Commercial Item Description for the procurement of the type I, class 2, vises specified in GGG-V-4 15A for all fe

2、deral agencies. 1. SCOPE. 1.1 Scppe. This Commercial Item Description covers a hinged jaw pipe vise used to hold various sizes of pipe and is capable of being mounted to a tripod stand or bench. 2. CLASSIFICATION. 0 2.1 Classification. Not applicable. 3. SALIENT CHARAmRIsTIcs. 3.1 m. The vise shall

3、consist of a base, frame and hook, jaw crosshead, jaws, screw and screw handle, and be similar to Figure 1. All parts having the same manufacturers number shali be direcy and completeiy interchangeable with each other with respect to installation and performance. Pipe sizes, screw diameters, and wei

4、ghts shall be in accordance with Table I. Figure 1. Vise, pipe, hinged jaw. t Beneficial comments, recommendations, additions, deletions, clarifications, etc., and any other data which may improve this document should be sent to: General Services Administration, Federal Supply Service, Tools and App

5、liances Commodity Center, Kansas City, MO 64 13 1. I I . -. Approved for public release; distribution is unlimited. FSC 5 120 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-3050 9999974 0372756 479 A-A-3050 TABLEI. Screw diameter Nominal pipe si

6、ze capacity* (minimum) (Inches) (inches) Weight (minimum) (Pounds) 118 to 2-112 1/8 to 4-112 118 to 6 1 to 8 1-112 to 12 718 1 1 - 118 1 - 118 1-318 10 23 35 75 160 * Capacities noted are the minimum and maximum required by are not intended to preclude vises with capacity below the minimum or above

7、the maximum (by not more than 1 inch) provided all other requirements are met. 3.1.1 w. The base shall be of malleable iron, ductile iron or steel and have at least three mounting holes. The vertical upright section of the base shall be provided with holes for the mounting of the fiame and shall hav

8、e provisions on both sides for automatic engagement of the iatch hook. The upright section of the base shall be symmeical about the vertical centerne to provide for hinging the frame from either the right or left side. The lower jaw mounting shall be so designed as to allow the vise to clamp the min

9、imum pipe-size capacity of the vise. 3.1.2 -. The frame and hook shall be of malleable iron, ductile iron or steel and shall be U-shaped. The open ends of the frame shall have mounting bolt holes to align with the bolt holes in the uprights of the base. The closed end shall have an internal threaded

10、 hole, compatible with the screw, in the center of the frame, or a means to hold a replaceable nut to engage the vise screw. The latch hook shall be of steel or malleable iron and shall be designed and mounted to automaticaily lock the frame in the closed position, and one of the legs shal have a ho

11、le for mounting the latch hook. The assembled fiame shall be so designed as to be reversible in a vertical plane to the base to provide for hinging the frame from either the right or left side of the base. The inside of the frame shall have mooth and parallel ways, free of burrs and fins, to act as

12、guides for the jaw crossheads and shall permit the crosshead to slide freely over the entire length of adjustment without binding. 3.1.3 Jaw crosshead. The jaw crosshead shall be of malleable iron, ductile iron, or steel. The design shall be such that the strength of the crosshead will be adequate f

13、or the purpose intended The top of the crosshead shall provide a means to allow the end of the screw to swivel and be designed to both raise and lower the crosshead by action of the screw. 3.1.4 or one coat of primer and one coat of air-drymg enamel or lacquer. in no case shaii frllers be used. 1 3.

14、2 . The tool shall be marked with the manufacturer?s name or identifying symbol and the state or country of manufacture, unless otherwise specified. All identification markings shall be engraved, etched, molded, or indented directly on the item?s surface in such a manner that it remains clearly legi

15、ble throughout the life of the item. . i I 3.3 . , Details of workmanship shall be in accordance with the best commercial practice. Paints, coatings, piatings, and finishes shall be smooth, adherent, continuous, and not stained or discolored. External surfaces shall be fiee of tool and gouge marks,

16、nicks, or other surface imperfections. The item shall be free from manufacturing workmanship defects (e.g., sharp or rough external edges, comers, or surfaces) and material workmanship defects (e.g., pits, rips, fins, burrs, tears, nodules, cracks, blisters) which may adversely impact the item?s ser

17、viceability, durability, safety, or appearance. 4. REGULATORY REQUIREMENTS. t 4.1 Recovered materials ? . The offeror/contractor is encouraged to use recovered materiais to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 4.2 . Products

18、 manufactured to metric dimensions wiii be considered on an eqd basis with those manufactured using inch-pound units, provided they faii within the tolerances specified (using conversion tables contained in the latest revision of Federal Standard 376) and all other requirements of this document are

19、met. If a product is manufactured to metric dimensions and those dimensions exceed the tolerances specified in the inch- pound units, a request should be made to the contracting officer to determine if the product is acceptable. 5. QUALITY ASSURANCE PROVISIONS. 5.1 Product. The product provided to t

20、he Government shall conform to the contractually specified requirements. For product characteristics and requirements which are not contractually specified, the provided product shai! conform to the producer?s own drawings, sandards, specifications, and quaiity assurance practices for the highest qu

21、ality product commercially offered by the producer. If the product is not commercially offered by the producer, the best commercial practices shall apply. The Government reserves the right to require proof of such conformances prior to first delivery and thereafter as provided for under the provisio

22、ns of the contract. . 5.2 . Unless otherwise specuied, the contractor is responsible for the performance of all inspection requirements and may use any commercial facilities (including the contractor?s own facilities) suitable for performance of the inspection requirements, unless disapproved by the

23、 Government. The Government reserves the right to perfom any inspections deemed necessary to assure the item conforms to the specified requirements. ? 5.3 . When a bid sample requirement is specified in the solicitation, the bid sample(s) shall be inspected for ail salient charactexistics by the Gov

24、ernment. A faiiure of any bid sample to meet the salient characteristics shall be cause for rejection. 5.4 shall be inspected for all salient characteristics. characteristics shall be cause for rejection. . When a first article requirement is specified in the contract, the first article sample(s) A

25、failure of any first article sample to meet the salient J 6. PACKAGING. 1 6.1 -. Requirements of preservation, packing, packaging, and marking of packages shall be as specified in the contract or order. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,

26、-,- A-A-3050 9999974 0372758 243 A-A-3050 7. NOTES. (This section conains infonnation of a general or explanatory nature that is not mandatory.) 7.1 Addresses for obtainuiged documents: s: Federal Supply Service Bureau, Specification Section, Suite 8100,470 LEnfant Plaza, SW, Washington, DC 20407. (

27、FA&): Government Printing Office, Superintendent of Documents, Washington, DC 20402-937 1. -OC 7.1 4: American Society for Quality Control, P.O. Box 3005, 611 East Wisconsin Avenue, Milwaukee, WI 43201-4606. ,4STM Eu: American Society for Testing and Materials, 100 Barr Hhbor Drive, West Conshohocke

28、n, PA 19428-2959. 7.2 ihk&a . Purchasers should select the preferred options permitted herein and should include the following information in procurement documents: (a) Title, number, and date of this Commercial Item Description. (b) When applicable, the appropriate NSN(s). (c) If bid samples are re

29、quired, the number of samples required, and the subjective inspection requirements. (d) If first article samples are required and the number of samples required. (e) If lot sampling inspection is re and the applicable lot sampling requirements. For example: -. Sampling for inspection (both examinati

30、ons and testing) shall be in accordance with ANSUASQC Z1.4. Each sample tool shall be examined and tested for all salient characteristics. The Inspection Level shall be S-2 with an Acceptable Quality Level of 4.0, expressed in terms of defects per hundred units. (f) What preservation, packing, packa

31、ging, and marking of packages are required. 7.3 mck N- . The following list of NSNs corresponds to the vises specified in this O. This list may not be indicative of ail possible NSNs associated with this CID. NSN SIZE 5 120-00-180-0649 5120-00-288-6518 1/8 inch to 2-1/2 inch pipe size 1/8inch to 4-1/2 inch pipe size MILITARY INTERESTS: NONE: DoD has no registered interest in revisions or notices to this Commercial Item Description until further notice. PREPARING ACTIVITY: GSA - FSS F Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-