FORD WRS-M1H1214-A-2010 FABRIC VOLTA S PATTERN FLAT WOVEN 100% PIR CONTENT TO BE USED WITH FORD WSS-M99P1111-A 《工业使用后材料比例达100%的VOLTA图案的平织织物 与标准FORD WSS-M99P1111-A一起使用 》.pdf

《FORD WRS-M1H1214-A-2010 FABRIC VOLTA S PATTERN FLAT WOVEN 100% PIR CONTENT TO BE USED WITH FORD WSS-M99P1111-A 《工业使用后材料比例达100%的VOLTA图案的平织织物 与标准FORD WSS-M99P1111-A一起使用 》.pdf》由会员分享，可在线阅读，更多相关《FORD WRS-M1H1214-A-2010 FABRIC VOLTA S PATTERN FLAT WOVEN 100% PIR CONTENT TO BE USED WITH FORD WSS-M99P1111-A 《工业使用后材料比例达100%的VOLTA图案的平织织物 与标准FORD WSS-M99P1111-A一起使用 》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions Rev. 1 2010 01 07 Revised Revised 3.2.2 M.Dumitrescu,NA 2009 09 22 Activated M. Dumitrescu, NA Printed copies are uncontrolled Copyright 2010, Ford Global Technologies, LLC Page 1 of 2 FABRIC, VOLTA S PATTERN, FLAT WOVEN WRS-M1H1214-A 100% PIR

2、 CONTENT 1. SCOPE The material defined by this specification is a Volta S pattern, Dobby, flat woven bodycloth of good quality and uniform composition. The fabric is made of 100% PIR (Post Industrial Recycled yarn) and it is backcoated. 2. APPLICATION This specification was released originally for m

3、aterial used as a seat fabric, insert and bolster application for 2010 U377 3. REQUIREMENTS In addition to the requirements listed herein, the fabric shall meet all requirements of: WSS-M8P18-A1/A4. 3.1 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform

4、 to the Companys Standard Requirements for Production Materials (WSS-M99P1111-A) 3.2 FABRIC CONSTRUCTION 3.2.1 Fabric Count, +/- 5% tolerance (ASTM D 3775) Warp 289 ends/10 cm Fill 190 picks/10 cm 3.2.2 Fabric Weight, +/- 5% tolerance (FLTM BN 106-01) Face Fabric w/backcoat 350 g/m2 Backcoat 50 g/m2

5、 3.3 COMPOSITION (ASTM D 629) Tolerance as specified in WSS-M8P18-A1/A4. Fabric 100% Polyester Backcoating Acrylic ENGINEERING MATERIAL SPECIFICATIONWRS-M1H1214-A Printed copies are uncontrolled Copyright 2010, Ford Global Technologies, LLC Page 2 of 2 3.4 YARN CONSTRUCTION (ASTM D 1244) Warp 16.7 t

6、ex (100% recycled polyester) x 3 Fill 16.7 tex (100% recycled polyester) x 3 3.5 METHOD OF DYEING Solution dye/yarn-package dye 3.6 FINISHING OPERATIONS Warping, weaving, backcoated, heat set 4. GENERAL INFORMATION The information given below is provided for clarification and assistance in meeting the requirements of this specification. 4.1 Purchase department will ensure that the material defined in this specification and shipped to any one assembly plant will be produced by one supplier only.