FORD FLTM EU-BI 001-05-2001 MEASUREMENT OF DRY HIDING POWER OF PAINTS (RED AND GREY STRAIGHT LINE HIDING CHART)《油漆的干覆盖力的测定（红色和灰色直线覆盖图）》.pdf

《FORD FLTM EU-BI 001-05-2001 MEASUREMENT OF DRY HIDING POWER OF PAINTS (RED AND GREY STRAIGHT LINE HIDING CHART)《油漆的干覆盖力的测定（红色和灰色直线覆盖图）》.pdf》由会员分享，可在线阅读，更多相关《FORD FLTM EU-BI 001-05-2001 MEASUREMENT OF DRY HIDING POWER OF PAINTS (RED AND GREY STRAIGHT LINE HIDING CHART)《油漆的干覆盖力的测定（红色和灰色直线覆盖图）》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、 FORD LABORATORY TEST METHOD EU-BI 001-05 Date Action Revisions 2001 03 02 Revised Editorial no technical change A. Cockman 1994 02 28 Printed copies are uncontrolled Page 1 of 4 Copyright 2001, Ford Global Technologies, Inc. MEASUREMENT OF DRY HIDING POWER OF PAINTS (Red and Grey Straight Line Hidi

2、ng Chart) Application This method is used to determine the dry hiding power of paints by measuring the film thickness required to completely hide red and grey stripes of a standard hiding chart. Apparatus and Materials Required Straight Line Hiding Chart Red and grey hiding chart. This is made up of

3、 standard colour lines, the red to match Munsell colour value 7.5 R (yR) 3/2, the grey to match Munsell neutral colour value N/6 medium grey. Reference number RGF-2. Source: Morest Company Inc. or Erichsen GmbH 71 Albany Avenue 587 Hemer Sundwig Freeport, NY 11520 W. Germany Masking Tape High temper

4、ature masking tape, 25 mm nominal width. Test Panels Body skin steel panels, dimensions 100 x 300 mm. Surface roughness 0.9 -1.8 micrometre C.L.A. or as otherwise specified in the relevant material specification. Colour Matching Device Macbeth Colour Matching Booth or equivalent with North Sky Dayli

5、ght according to BI 109-01. Film Thickness Measuring Device According to FLTM BI 117-01 e.g. Permascope ES8 Source: Fischer Instruments or Fischer Instrumentation (G.B.) Ltd. Stuttgart Arnhem Industrial Estate W. Germany Arnhem Road Newbury Berkshire FORD LABORATORY TEST METHOD EU-BI 001-05 Page 2 o

6、f 4 Copyright 2001, Ford Global Technologies, Inc. Conditioning and Test Conditions All test values indicated herein are based on material conditioned in a controlled atmosphere of 23 +/- 2 C and 50 +/- 5 % relative humidity for not less than 24 h prior to testing and tested under the same condition

7、s unless otherwise specified. Procedure 1. Position the chart on the panel even with the left edge and about 15 mm inboard from the upper and lower edge. Tape the cardboard to the panel using high temperature masking tape. The tape should cover only about 10 mm of the chart at the top and bottom end

8、s. 2. The paint should be thinned to the viscosity required by the relevant Material Specification with the solvent specified. Viscosity to be determined in accordance with FLTM BI 111-01. 3. Spray the entire panel and chart with a uniform, wet coating of the test colour approx 12 micrometre thick.

9、4. Allow 1 minute flash-off, then spray the lower 3/4 of the panel with an additional 12 micrometre coat of paint. 5. Allowing 1 minute flash-off between coats, progressively spray the remaining lower areas of the panel until complete hiding of the red and grey stripes is obtained at the lower end o

10、f the panel. Note: Some practice may be required to accomplish the object of this test. A gradual increase in film thickness from the top to the bottom of the panel is desired with a dry film thickness gradient of 12 micrometre to 60 micrometre. A wedge type film thickness with complete hiding of th

11、e lower chart stripes is obtained when the panel is sprayed in increments with successive coats of paint. 6. Flash-off for 3 minutes after final coat, then bake the panel at one of the standard cycles designated by the relevant Material Specification. Remove baked panel from the oven and cool to 23

12、+/- 2 C. FORD LABORATORY TEST METHOD EU-BI 001-05 Page 3 of 4 Copyright 2001, Ford Global Technologies, Inc. Evaluation 1. Examine painted chart under the North Sky Daylight of the Macbeth unit. The panel should be viewed at various angles in order to determine the point where complete hiding of the

13、 red and grey stripes on the chart begins. 2. Remove panel from the Macbeth unit and according to FLTM EU-BI 017-01 measure the paint thickness on the steel panel adjacent to the area of the chart marked as having complete hiding. Record this measurement and report as the dry hiding (red and grey st

14、raight line chart) thickness of paint. Chemicals, materials, parts, and equipment referenced in this document must be used and handled properly. Each party is responsible for determining proper use and handling in its facilities. FORD LABORATORY TEST METHOD EU-BI 001-05 Page 4 of 4 Copyright 2001, Ford Global Technologies, Inc. MEASUREMENT OF DRY HIDING POWER OF PAINTS (Red and Grey Straight Line Hiding Chart)