ETSI TS 103 161-11-2011 Access Terminals Transmission and Multiplexing (ATTM) Integrated Broadband Cable and Television Networks IPCablecom 1 5 Part 11 Media terminal adapter (MTA)_1.pdf

《ETSI TS 103 161-11-2011 Access Terminals Transmission and Multiplexing (ATTM) Integrated Broadband Cable and Television Networks IPCablecom 1 5 Part 11 Media terminal adapter (MTA)_1.pdf》由会员分享，可在线阅读，更多相关《ETSI TS 103 161-11-2011 Access Terminals Transmission and Multiplexing (ATTM) Integrated Broadband Cable and Television Networks IPCablecom 1 5 Part 11 Media terminal adapter (MTA)_1.pdf（79页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI TS 103 161-11 V1.1.1 (2011-10) Access, Terminals, Transmission and Multiplexing (ATTM); Integrated Broadband Cable and Television Networks; IPCablecom 1.5; Part 11: Media terminal adapter (MTA) device provisioning Technical Specification ETSI ETSI TS 103 161-11 V1.1.1 (2011-10)2Reference DTS/A

2、TTM-003011-11 Keywords access, broadband, cable, IP, multimedia, PSTN ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 78

3、03/88 Important notice Individual copies of the present document can be downloaded from: http:/www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference ver

4、sion is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of st

5、atus. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http:/portal.etsi.org/chaircor/ETSI_support.asp Copyright Notific

6、ation No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2011. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI

7、 registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSMand the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI TS 103 161-11 V1.1.1 (2011-10)3Contents Int

8、ellectual Property Rights 6g3Foreword . 6g31 Introduction 8g31.1 Scope 8g32 References 8g32.1 Normative references . 8g32.2 Informative references 10g33 Definitions and abbreviations . 10g33.1 Definitions 10g33.2 Abbreviations . 11g34 Void 12g35 Background 12g35.1 Service Goals 12g35.2 Document Goal

9、s . 12g35.3 IPCablecom Reference Architecture 13g35.4 Components and Interfaces 14g35.4.1 MTA . 14g35.4.1.1 MTA Security Requirements 15g35.4.1.2 MTA SNMP Requirements . 15g35.4.2 Provisioning Server. 15g35.4.3 MTA to Telephony Syslog Server 16g35.4.4 MTA to DHCP Server 16g35.4.5 MTA to Provisioning

10、 Application 16g35.4.6 MTA to CMS 17g35.4.7 MTA to Security Server (KDC) 17g35.4.8 MTA and Configuration Data File Access . 17g35.4.9 DOCSISextensions for MTA Provisioning 17g36 Provisioning Overview . 18g36.1 Device Provisioning . 18g36.2 Endpoint Provisioning 18g36.3 Secure Flow Provisioning State

11、 Transitions . 18g36.4 Basic and Hybrid Flow Provisioning State Transitions 19g37 Provisioning Flows . 20g37.1 Backoff, Retries, and Timeouts 21g37.2 Embedded-MTA Power-On Initialization Flow (Secure Flow) . 22g37.2.1 Embedded-MTA Secure Power-on Initialization Flow (IPv4 eCM) 22g37.2.2 Embedded-MTA

12、 Secure Power-on Initialization Flow (IPv6 eCM) 28g37.3 Embedded-MTA Power-On Initialization Flow (Basic Flow) . 30g37.4 Embedded-MTA Power-On Initialization Flow (Hybrid Flow). 31g37.5 Endpoint Provisioning Completion Notifications 33g37.6 Post Initialization Incremental Provisioning 34g37.6.1 Sync

13、hronization of Provisioning Attributes with Configuration File . 34g37.6.2 Adding/Enabling Telephony Services on an MTA Endpoint . 34g37.6.3 Deleting/Disabling Telephony Services on an MTA Endpoint. 35g37.6.4 Modifying Telephony Services on an MTA Endpoint 36g37.7 Reflecting the State of the Endpoin

14、t Interface in the ifTable . 36g37.8 Provisioning of the Signalling Communication Path Between the MTA and CMS . 37g37.9 MTA Replacement . 37g37.10 Temporary Signal Loss 37g37.11 MTA Hard Reboot/Soft Reset scenarios. . 37g38 DHCP Options 37g3ETSI ETSI TS 103 161-11 V1.1.1 (2011-10)48.1 DHCP Option 1

15、22: CableLabsClient Configuration Option . 38g38.1.1 Service Providers DHCP Address (sub-option 1 and 2) 39g38.1.2 Service Providers Provisioning Entity Address (sub-option 3) 39g38.1.3 AS-REQ/REP Exchange Backoff and Retry for SNMPv3 Key Management (sub-option 4) 39g38.1.4 AP-REQ/REP Kerberized Pro

16、visioning Backoff and Retry (sub-option 5) 40g38.1.5 Kerberos Realm of SNMP Entity (sub-option 6) 40g38.1.5.1 SNMPv3 Key Establishment . 41g38.1.6 Ticket Granting Server Usage (sub-option 7) . 41g38.1.7 Provisioning Timer (sub-option 8) 41g38.1.8 Security Ticket Invalidation (sub-option 9) 41g38.2 D

17、HCP Option 60: Vendor Client Identifier 42g38.3 DHCP Options 12 and 15 . 42g38.4 DHCP Option 6 42g38.5 DHCP Option 43 42g38.6 DHCP OPTION 1 . 44g38.7 DHCP OPTION 3 . 44g38.8 DHCP OPTION CL_V4_PACKETCABLE_MIB_ENV_OPTION 44g39 MTA Provisionable Attributes . 44g39.1 MTA Configuration File 45g39.1.1 Dev

18、ice Level Configuration Data . 49g39.1.2 Device Level Service Data 50g39.1.3 Per-Endpoint Configuration Data . 52g39.1.4 Per-Realm Configuration Data . 54g39.1.5 Per-CMS Configuration Data . 55g39.1.6 Exclusion of MIB objects in configuration File 56g310 MTA Device Capabilities . 56g310.1 IPCablecom

19、 Version. 57g310.2 Number Of Telephony Endpoints 57g310.3 TGT Support 57g310.4 HTTP Download File Access Method Support 57g310.5 MTA-24 Event SYSLOG Notification Support . 57g310.6 NCS Service Flow Support 58g310.7 Primary Line Support . 58g310.8 Vendor Specific TLV Type(s) 58g310.9 NVRAM Ticket/Tic

20、ket Information Storage Support 58g310.10 Provisioning Event Reporting Support . 58g310.11 Supported CODEC(s) . 58g310.12 Silence Suppression Support 59g310.13 Echo Cancellation Support . 59g310.14 RSVP Support 59g310.15 UGS-AD Support . 59g310.16 MTAs “ifIndex“ starting number in “ifTable“ . 59g310

21、.17 Provisioning Flow Logging Support 60g310.18 Supported Provisioning Flows . 60g310.19 T38 Version Support 60g310.20 T38 Error Correction Support 61g310.21 RFC 2833 DTMF Support 61g310.22 Voice Metrics Support 61g310.23 Device MIB Support 61g310.23.1 Issuing Organization Assignments . 62g310.23.2

22、Representing CableLabsMIBs . 62g310.23.3 Representing IETF MIBs 62g310.23.4 Example 62g310.24 Multiple Grants Per Interval Support . 63g310.25 V.152 Support 63g311 TLV-38 SNMP Notification Receiver Specification . 63g311.1 Sub-TLVs of TLV-38 . 63g311.1.1 SNMP Notification Receiver IP Address 63g311.

23、1.2 SNMP Notification Receiver UDP Port Number 64g311.1.3 SNMP Notification Receiver Type . 64g3ETSI ETSI TS 103 161-11 V1.1.1 (2011-10)511.1.4 SNMP Notification Receiver Timeout 64g311.1.5 SNMP Notification Receiver Retries 64g311.1.6 SNMP Notification Receiver Filtering Parameters . 64g311.1.7 SNM

24、Pv3 Notification Receiver Security Name . 65g311.2 Mapping of TLV fields into SNMP Tables 65g311.2.1 Mapping of TLV fields into created SNMP Table rows . 65g311.2.1.1 snmpNotifyTable 66g311.2.1.2 snmpTargetAddrTable 66g311.2.1.3 snmpTargetAddrExtTable . 66g311.2.1.4 snmpTargetParamsTable . 67g311.2.

25、1.5 snmpNotifyFilterProfileTable . 67g311.2.1.6 snmpNotifyFilterTable 67g311.2.1.7 snmpCommunityTable 67g311.2.1.8 usmUserTable . 68g311.2.1.9 vacmSecurityToGroupTable . 69g311.2.1.10 VacmAccessTable . 69g311.2.1.11 vacmViewTreeFamilyTable 69g311.3 TLV38 and TLV11 Configuration Example 70g311.3.1 TL

26、V-38 Example 70g311.3.2 Content of the SNMP framework tables after processing of the above example TLV38s 70g312 SNMPv2c Management Requirements 72g312.1 SNMPV2c Co-existence mode tables content created by MTA after MTA-4 for Hybrid and Basic Flows. . 73g312.2 SNMP Default entries for SNMPv2c Access

27、 . 73g313 Service interruption impact reporting and other enhanced features support 75g313.1 eDOCSISRequirements support 75g313.1.1 Impact Analysis and Reporting Requirements: 75g313.1.1.1 Impact Analysis . 76g313.1.1.2 Supported Impact Levels and Reporting . 76g313.2 IPCablecom Extension MIB . 76g3

28、13.2.1 MTA MIB Extension 76g313.2.2 Signalling MIB Extension 76g313.3 Battery Backup MIBS 76g313.4 Syslog MIBS 76g313.5 Foreign Potential Detection 76g3Annex A (informative): SNMPv2c co-existence Configuration Example - Template for service providers . 77g3Annex B (informative): Bibliography . 78g3H

29、istory 79g3ETSI ETSI TS 103 161-11 V1.1.1 (2011-10)6Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can

30、 be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/ipr.etsi.org). Pursuant to the ETSI I

31、PR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword Th

32、is Technical Specification (TS) has been produced by ETSI Technical Committee Access, Terminals, Transmission and Multiplexing (ATTM). The present document is part 11 of a multi-part IPCablecom 1.5 deliverable covering the Digital Broadband Cable Access to the Public Telecommunications Network; IP M

33、ultimedia Time Critical Services, as identified below: Part 1: “Overview“; Part 2: “Architectural framework for the delivery of time critical services over Cable Television Networks using Cable Modems“; Part 3: “Audio Codec Requirements for the Provision of Bi-Directional Audio Service over Cable Te

34、levision Networks using Cable Modems“; Part 4: “Network Call Signalling Protocol“; Part 5: “Dynamic Quality of Service for the Provision of Real Time Services over Cable Television Networks using Cable Modems“; Part 6: “Event Message Specification“; Part 7: “Media Terminal Adapter (MTA Management In

35、formation Base (MIB)“; Part 8: “Network Call Signalling (NCS) MIB Requirements“; Part 9: “Security“; Part 10: “Management Information Base (MIB) Framework“; Part 11: “Media terminal adapter (MTA) device provisioning“; Part 12: “Management Event Mechanism“; Part 13: “Trunking Gateway Control Protocol

36、 - MGCP option“; Part 14: “Embedded MTA Analog Interface and Powering Specification“ Part 15: “Analog Trunking for PBX Specification“; Part 16: “Signalling for Call Management Server“; Part 17: “CMS Subscriber Provisioning Specification“; Part 18: “Media Terminal Adapter Extension MIB“; Part 19: “IP

37、Cablecom Audio Server Protocol Specification - MGCP option“; Part 20: “Management Event MIB Specification“; ETSI ETSI TS 103 161-11 V1.1.1 (2011-10)7Part 21: “Signalling Extension MIB Specification“. NOTE 1: Additional parts may be proposed and will be added to the list in future versions. NOTE 2: T

38、he choice of a multi-part format for this deliverable is to facilitate maintenance and future enhancements. ETSI ETSI TS 103 161-11 V1.1.1 (2011-10)81 Introduction The present document describes the IPCablecom 1.5 embedded-MTA device initialization and provisioning. The present document is issued to

39、 facilitate design and field-testing leading to manufacturability and interoperability of conforming hardware and software by multiple vendors. 1.1 Scope The scope of the present document is limited to the provisioning of a IPCablecom 1.5 embedded-MTA device by a single provisioning and network mana

40、gement provider. An attempt has been made to provide enough detail to enable vendors to build an embedded-MTA device that is interoperable in an IPCablecom 1.5 network configuration. The present document defines the provisioning of MTA components of the embedded MTA device (unless stated otherwise).

41、 2 References References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the reference document (including any amendments) appl

42、ies. Referenced documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. 2.1 Normative r

43、eferences The following referenced documents are necessary for the application of the present document. 1 IETF RFC 2131: “DHCP: Dynamic Host Configuration Protocol“, March 1997. 2 ETSI TS 103 161-7: “Access, Terminals, Transmission and Multiplexing (ATTM); Integrated Broadband Cable and Television N

44、etworks; IPCablecom 1.5; Part 7: Media Terminal Adapter (MTA) Management Information Base (MIB)“. 3 ETSI TS 103 161-8: “Access, Terminals, Transmission and Multiplexing (ATTM); Integrated Broadband Cable and Television Networks; IPCablecom 1.5; Part 8: Network Call Signalling (NCS) MIB Requirements“

45、. 4 ETSI TS 103 161-4: “Access, Terminals, Transmission and Multiplexing (ATTM); Integrated Broadband Cable and Television Networks; IPCablecom 1.5 Part 4: Network Call Signalling Protocol“. 5 ETSI TS 103 161-9: “Access, Terminals, Transmission and Multiplexing (ATTM); Integrated Broadband Cable and

46、 Television Networks; IPCablecom 1.5; Part 9: Security“. 6 ETSI ES 201 488: “Access and Terminals (AT); Data Over Cable Systems“. 7 IETF RFC 3413/STD0062: “Simple Network Management Protocol (SNMP) Applications“, December 2002. 8 IETF RFC 3414/STD0062: “User-based Security Model (USM) for version 3

47、of the Simple Network Management Protocol (SNMPv3)“, December 2002. 9 IETF RFC 3415/STD0062: “View-based Access Control Model (VACM) for the Simple Network Management Protocol (SNMP)“, December 2002. ETSI ETSI TS 103 161-11 V1.1.1 (2011-10)910 IETF RFC 3396: “Encoding Long Options in the Dynamic Hos

48、t Configuration Protocol (DHCPv4)“, November 2002. 11 IETF RFC 2132: “DHCP Options and BOOTP Vendor Extensions“, March 1997. 12 ANSI/SCTE 107 2009: “Embedded Cable Modem Devices“. 13 ETSI TS 103 161-20: “Access, Terminals, Transmission and Multiplexing (ATTM); Integrated Broadband Cable and Televisi

49、on Networks; IPCablecom 1.5; Part 20: Management Event MIB Specification“. 14 ETSI TS 103 161-12: “Access, Terminals, Transmission and Multiplexing (ATTM); Integrated Broadband Cable and Television Networks; IPCablecom 1.5 Part 12: Management Event Mechanism“. 15 ETSI TS 103 161-21: “Access, Terminals, Transmission and Multiplexing (ATTM); Integrated Broadband Cable and Television Networks; IPCablecom 1.5; Part 21: Signalling Extension MIB Specification“. 16 ETSI TS 103 161-18: “Access, Terminals, Transmission and Multiplexing (ATTM); In