EN ISO 12048-2000 en Packaging - Complete Filled Transport Packages - Compression and Stacking Tests Using a Compression Tester《包装 完全满运输包装件 利用压缩试验机的压缩试验和堆积试验 ISO 12048-1994 代替EN 22.pdf

《EN ISO 12048-2000 en Packaging - Complete Filled Transport Packages - Compression and Stacking Tests Using a Compression Tester《包装 完全满运输包装件 利用压缩试验机的压缩试验和堆积试验 ISO 12048-1994 代替EN 22.pdf》由会员分享，可在线阅读，更多相关《EN ISO 12048-2000 en Packaging - Complete Filled Transport Packages - Compression and Stacking Tests Using a Compression Tester《包装 完全满运输包装件 利用压缩试验机的压缩试验和堆积试验 ISO 12048-1994 代替EN 22.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、STDmBSI BS EN IS0 12048-ENGL 2001 1b24bb9 0892200 073 BRITISH STANDARD BS EN IS0 12048:2001 Packaging - Complete, filled transport packages - Compression and stacking tests using a compression tester The European Standard EN IS0 12048:2000 has the status of a British Standard ICs 55.180.40 NO COPYIN

2、G WITHOUT BSI PERMISSION EXCEPT AS PERMIITED BY COPYRIGH“ LAW STD*BSI BS EN IS0 L2048-ENGL 2101 M 1624669 0892201 TOT BS EN IS0 12048:2001 direction of the Consumer AmdNo. products and Services Sector Committee, was published under the authority of the Standards Committee and comes into effect on 15

3、 February 2001 O BSI 02-2001 National foreword Date Comments This British Standad is the official English language version of EN IS0 12048:2000. It is identical with IS0 12048:1994. It supersedes BS IS0 12W1994 which is withdrawn. The UK participation in its preparation was entrusted by Technical Co

4、mmittee PKW/l, Packaging generalities, to Subcommittee PKW/1/4, Test methods, which has the responsibility to: - aid enquirers to understand the te* - present to the responsible inkrnatio or in the case of a stacking test, a predetermined load is applied for a predetermined time or until failure occ

5、urs. Apparatus 4.1 Compression tester, motor-driven, platen-type, capable of applying load through uniform movement of one or both platens at a relative speed of 10 mm/min 2 3 mm/min. NOTES 1 The comparison between results obtained from apparatus operated at other speeds (for example 12,5 mdmin I 2,

6、5 mdmin) and results obtained at 10 mdmin 2 3 mmlmin is not recommended. 2 For certain packagings, such as metal drums or wooden crates, lower speeds may be required to prevent load peaks in excess of the predetermined value. 4.1.1 Platens Each platen shall be - flat: a) with a tolerance of 1 part i

7、n 1 O00 for surface areas 1 m2, such that when placed horizontally the difference in height between the lowest and highest points of the platen does not exceed 1 mm; - dimensioned so as to extend over the whole area of that side of the test package or interposed devices with which it is in contact;

8、1) To be published. (Revision of IS0 2233:1986) 1 STD.BSI BS EN IS0 L204B-ENGL 2001 3b24bb9 0892206 591 EN IS0 12048:2000 - rigid, so as not to deform by more than 1 mm at any point when the tester applies a load of 75 % of its maximum rating, either to a centrally placed 100 mm X 100 mm X 100 mm bl

9、ock having suf- ficient strength to accept the load without failure, or to four similar blocks placed at the four corners, in the case of swivel-mounted platens. One platen shall remain horizontal, within a tolerance of two parts per 1000, at all times during the test. The other platen shall be eith

10、er rigidly mounted so as to remain horizontal within two parts per 1 O00 at all times during the test, or be held by a universal joint at its centre and so be free to tilt in any direction. The working surfaces of the platens may be locally recessed for fixing bolts etc. 4.1.2 Means of applying a pr

11、edetermined load for a predetermined time, with a fluctuation not exceeding +- 4 % of the predetermined load and with no more relative movement of the platens than is necessary to maintain this load during any vertical displacement of the upper platen. 4.2 Recording device or other means of indicati

12、ng applied load and platen displacement, with a percentage of error not exceeding 2 % of the load and an accuracy for recording platen displacement of 2 1 mm. 4.3 Means of measuring package dimensions with an accuracy of I 1 mm. 5 Package preparation The test package shall normally be filled with it

13、s intended contents. However, simulated or dummy contents may be used, on condition that the dimensions and physical properties of such contents shall be as close as possible to those of the intended contents. Ensure that the test package is closed normally, as if ready for distribution. If simulate

14、d or dummy contents are used, ensure that the normal method of closure is still employed. 6 Conditioning The package shall be conditioned in accordance with one of the sets of conditions given in IS0 2233. 7 Procedure Wherever possible the test shall be carried out in the same atmospheric conditions

15、 as used for condition- ing, where this is critical to the materials or application of the package. In other circumstances, the test shall be carried out in atmospheric conditions which are as near as practicable to those used for conditioning. When possible, carry out the test on five replicate pac

16、kages. 7.1 Compression test 7.1.1 Weigh the package and its contents separately, fill the package and measure the external dimensions of the filled package. 7.1.2 Place the test package centrally on the lower platen of the test machine (4.11, in the predetermined attitude. When the compression load

17、is not to be applied over the whole surface of the package which is being tested, appropriate devices should be suitably interposed between the package and platen of the compression tester in order to simulate the conditions met in distribution systems when applying these compression loads. 7.1.3 Ap

18、ply the load by relative movement of the platens at the appropriate speed, in such a way that peaks in excess of the predetermined load do not occur, until the predetermined value is reached or until collapse occurs, whichever is first. If collapse occurs first, record the value of the load reached.

19、 In measuring deformation, the initial reading (the datum point), unless otherwise specified, shall be taken at an initial load which is a function of the expected average compression load according to table 1. Table 1 - Datum points Average compression load N 101 -200 201 - 1 O00 1 O01 -2 O00 2 O01

20、 - 10 O00 10001 -20000 20 O01 - 100 O00 etc. Datum point N 10 25 loo 250 1 O00 2 500 etc. 7.1.4 If required, maintain the Predetermined load for a predetermined time or until collapse occurs, whichever is first. If collapse occurs first, record the value of the time elapsed. 7.1.5 Remove the load by

21、 movement of the platens, examine the package and, if collapse has occurred, measure its dimensions and examine the contents for damage. 7.1.6 Where it is desired to measure the ability of a complete, filled transport package to resist external 2 STD.BSI BS EN IS0 l.12048-ENGL 2001 Lb24bb9 0892207 4

22、28 H EN IS0 12048:2000 compressive loads applied to opposite edges or of the package and its fittings, cushioning, corners of the package, follow the procedure in 7.1.1 blocking, closure or reinforcing arrangements; to 7.1.5, using a tester in which the platens are not free to tilt. e) description o

23、f the contents - if simulated or dummy contents were used, full details shall be given; 7.2 Stacking test NOTE 3 A stacking test on a complete, filled transport package, using one of three methods of applying a static load, is given in IS0 2234. 7.2.1 Proceed as in 7.1.1 to 7.1.3 and maintain the pr

24、edetermined load for a predetermined time or until collapse occurs, whichever is first. If collapse occurs first, record the value of the time elapsed. NOTE4 Where it is desired to measure the ability of a complete, filled transport package to resist external cornpressive loads applied during stacki

25、ng, a tester with one fixed platen is preferred. 7.2.2 Remove the load by movement of the platens, examine the package and, if collapse has occurred, measure its dimensions and examine the contents for damage. NOTES 5 At any time during the test it may be necessary to measure dimensions (see annex A

26、). 6 Appropriate profiles representative of particular loading conditions may be inserted between platens and package as required. 8 Testreport The test report shall include the following information: f) gross mass of the package and mass of contents, in kilograms; g) relative humidity, temperature

27、and time of conditioning; temperature and relative humidity of test area at time of test; whether these values comply with the requirements of IS0 2233; hl the attitude in which the package was tested, using the method of identification given in IS0 2206; i) type of test apparatus used, including wh

28、ether the compression tester was mechanically or hydraulically operated and whether or not both platens were rigidly mounted; j) location of measurement points on packages and stage of test at which measurements were made; k) design and dimensions of any profiles used; i) test conditions, .e.: the r

29、ate of application of the load (see 4.11, the load applied, in newtons, and duration of application of load to the package; m) a record of the average results, including load applied until collapse if less than the predetermined load, the time elapsed until collapse if less than the predetermined ti

30、me, any observed changes in package dimensions and, if required, load/$aten displacement recording, with any observations which may assist in correct interpretation; n) any deviation from the test methods described in this International Standard; a) reference to this International Standard; b) wheth

31、er a compression or stacking test was carried out; c) number of replicate packages tested; d) full description of the package, including o) date of test; dimensions, structural and material specifications p) signature of tester. 3 STD-BSI BS EN IS0 12046-ENGL 2001 Lb24bb9 0892208 3b4 EN IS0 12048:20

32、00 Annex A (informative) Example of a method of measuring package deformation load A.1 Place the weighed, filled transport package 113 Apply the predetermined load for a predetermined centrally between the platens and apply, at the standard rate of 10 mm/min I 3 mm/min, an initial load of amroximate

33、lv 10 % of the value of the predetermined time. lwd to be applied. A.4 Repeat the dimensional measurements, in the -2 Take a preliminary seiec of dimensioml measurements of the package from the surfaces which apply the load to the package to several points along the vertical edges of the package and

34、, optionally, along the sides. same positions as in A2, at predetermined stages during application of the load. NOTE 7 The average dfom&mi may be measured t-e simply by using a chart recorder. 4 STD.BSI BS EN IS0 L2048-ENGL 2001 Lb24bb9 0892209 2TO EN IS0 12048:2000 Annex B (inform at ive) Bibliogra

35、phy i 1 IS0 2234: 1985, Packaging - Complete, filled transport packages - Stacking rests using static load. 5 STD.BSI BS EN IS0 12048-ENGL ZOO1 1624669 0892210 T12 EN IS0 12048:2000 Annex ZA (normative) Normative references to international publications with their corresponding European publications

36、 This European Standard incorporates, by dated or undated reference, provisions from other publications. These normativereferences are cited at the appropriate places in the text, and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these p

37、ublications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies (including amendments). NOTE Where an International Publication has been modified by common modifications, indicated by

38、(mod.), the relevant ENRID applies. Publication Year Title - EN - Year IS0 2206 1987 Packaging - Complete, filled transport EN 22206 1992 packages - Identification of parts when testing BS EN IS0 12048:2001 BSI 389 Chimvick High Road London w4 4AL BSI - British Standards Institution BSI is the indep

39、endent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the inte&ond level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Stan- should make sure that they possess

40、 the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British standard would inform the Secretary of the technical committee responsible, the identity o

41、f which can be found on the inside front cover. Tel: O20 8996 9OOO. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of sandards. Buying standards orders for all BSI, international and foreign s

42、tandards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. Standards are also available from the BSI website at http:/lwww.bsi-. in response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been p

43、ublished as British Stanwds, unless otherwise requested Information on standards BSI provides a wide range of infomation on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available w

44、hich give details on all its products and services. Contact the Information Centre. Tel: O20 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other

45、benefits contact Membership Admhbtmh OIL Tel: O20 8996 7002. Fax O20 8996 7001. Further information about BSI is available on the BSI website at httphww.bsi-. copyright Copyright subsists in ali BSI publications. BSI also holds the copyright, in the UK, of the pubiidions of the international standar

46、mon bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retried system or transmitted in any form or by any means - electronic, photocopying, recording or otherwise - without prior written pennicsion from BSI. This does not preclude

47、 the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written pennission of BSI must be obtained if pennission is granted, the terms may include royalty payments or a licensing agreement Details and advice can be obtained from the Copyright Manager. Tel: O20 8996 7070.