EN 60384-3-1-2006 en Fixed capacitors for use in electronic equipment Part 3-1 Blank detail specification Surface mount fixed tantalum electrolytic capacitors with manganese dioxid.pdf

《EN 60384-3-1-2006 en Fixed capacitors for use in electronic equipment Part 3-1 Blank detail specification Surface mount fixed tantalum electrolytic capacitors with manganese dioxid.pdf》由会员分享，可在线阅读，更多相关《EN 60384-3-1-2006 en Fixed capacitors for use in electronic equipment Part 3-1 Blank detail specification Surface mount fixed tantalum electrolytic capacitors with manganese dioxid.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 60384-3-1:2006Fixed capacitors for use in electronic equipment Part 3-1: Blank detail specification: Surface mount fixed tantalum electrolytic capacitors with manganese dioxide solid electrolyte Assessment level EZICS 31.060.40g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g5

2、5g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58Incorporating orrigendaApril 2009 andcMarch 2010National forewordThis British Standard is the UK implementation of EN 60384-3-1:2006, incorporating cor

3、rigendum April 2009. It is identical to IEC 60384-3-1:2006. It supersedes BS QC 300801:1993 which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee EPL/40X, Capacitors and resistors for electronic equipment.A list of organizations represented on this committee

4、 can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.BS EN 60384-3-1:2006This British St

5、andard was published under the authority of the Standards Policy and Strategy Committee on 31 March 2008 BSI 2010Amendments/corrigenda issued since publicationDate Comments 31 July 2009 Implementation of CENELEC corrigendum April 2009, which updates supersession information31 March 2010 Supersession

6、 text amendedISBN 978 0 580 70371 3EUROPEAN STANDARD EN 60384-3-1 NORME EUROPENNE EUROPISCHE NORM December 2006 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de

7、 Stassart 35, B - 1050 Brussels 2006 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60384-3-1:2006 E ICS 31.060.30 English version Fixed capacitors for use in electronic equipment Part 3-1: Blank detail specification: Surface mou

8、nt fixed tantalum electrolytic capacitors with manganese dioxide solid electrolyte - Assessment level EZ (IEC 60384-3-1:2006) Condensateurs fixes utiliss dans les quipements lectroniques Partie 3-1: Spcification particulire cadre: Condensateurs fixes lectrolytiques au tantale pour montage en surface

9、 lectrolyte solide en bioxyde de manganse - Niveau dassurance de la qualit EZ (CEI 60384-3-1:2006) Festkondensatoren zur Verwendung in Gerten der Elektronik Teil 3-1: Vordruck fr Bauartspezifikation: Oberflchenmontierbare Tantal-Kondensatoren mit festem Mangandioxid-Elektrolyt - Qualittsbewertungsst

10、ufe EZ (IEC 60384-3-1:2006) This European Standard was approved by CENELEC on 2006-11-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-dat

11、e lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under

12、the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany,

13、 Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Supersedes EN 130801:2002Incorporating Co rrigendum April 2009Foreword The text of document 40/1

14、772/FDIS, future edition 2 of IEC 60384-3-1, prepared by IEC TC 40, Capacitors and resistors for electronic equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60384-3-1 on 2006-11-01. This European standard supersedes EN 130801:2002.The following dates were f

15、ixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2007-08-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2009-11-01 Annex ZA has been added by CENELEC.

16、_ Endorsement notice The text of the International Standard IEC 60384-3-1:2006 was approved by CENELEC as a European Standard without any modification. _ 2 EN 60384-3-1:2006BS EN 60384-3-1:2006The contents of the corrigendum of April 2009 have been included in this copy.FIXED CAPACITORS FOR USE IN E

17、LECTRONIC EQUIPMENT Part 3-1: Blank detail specification: Surface mount fixed tantalum electrolytic capacitors with manganese dioxide solid electrolyte Assessment level EZ INTRODUCTION Blank detail specification A blank detail specification is a supplementary document to the sectional specification

18、and contains requirements for style, layout and minimum content of detail specifications. Detail specifications not complying with these requirements may not be considered as being in accordance with IEC specifications nor shall they so be described. In the preparation of detail specifications, the

19、content of 1.4 of the sectional specification shall be taken into account. The numbers between square brackets on the first page of the detail specification correspond to the following information, which shall be inserted in the position indicated. Identification of the detail specification 1 The “I

20、nternational Electrotechnical Commission” or the National Standards Organization under whose authority the detail specification is drafted. 2 The IEC or National Standards number of the detail specification, date of issue and any further information required by the national system. 3 The number and

21、issue number of the IEC or national generic specification. 4 The IEC number of the blank detail specification. Identification of the capacitor 5 A short description of the type of capacitor. 6 Information on typical construction (when applicable). NOTE When the capacitor is not designed for use in p

22、rinted circuit board applications, this is clearly stated in the detail specification in this position. 7 Outline drawing with main dimensions which are of importance for interchangeability and/or reference to the national or international documents for outlines. Alternatively, this drawing may be g

23、iven in an annex to the detail specification. 8 Application or group of applications covered and/or assessment level. 9 Reference data on the most important properties, to allow comparison between the various capacitor types. 3 EN 60384-3-1:2006BS EN 60384-3-1:20061 IEC 60384-3-1-XXX 2 QC 300801-XXX

24、 IEC 60384-3-1 4 QC 300801 ELECTRONIC COMPONENTS OF ASSESSED QUALITY IN ACCORDANCE WITH: IEC 60384-1 IEC 60384-3 3 SURFACE MOUNT FIXED TANTALUM ELECTROLYTIC CAPACITORS WITH MANGANESE DIOXIDE SOLID ELECTROLYTE 5 6 OUTLINE DRAWING: (see Table 1) (first angle projection) 7 (Other shapes are permitted w

25、ithin the dimensions given.) ASSESSMENT LEVEL(S): EZ 8 NOTE For 1 to 9: see previous page. 9 Information on the availability of components qualified to this detail specification is given in the Qualified Products List. 1 General data 1.1 Recommended method of mounting (to be inserted) The capacitors

26、 are mounted by their terminations (see 1.3.2 and 4.3 of IEC 60384-3). 1.2 Dimensions Table 1 Case-size reference and dimensions Dimensions mm or inches and mm Case-size reference l h d When there is no case-size reference, Table 1 may be omitted and the dimensions shall be given in Table 2, which t

27、hen becomes Table 1. 4 EN 60384-3-1:2006BS EN 60384-3-1:2006The dimensions shall be given as maximum dimensions or as nominal dimensions with a tolerance. 1.3 Ratings and characteristics Capacitance range (see Table 2) Tolerance on rated capacitance Rated voltage (see Table 2) Category voltage (if a

28、pplicable) (see Table 2) Climatic category Rated temperature Variation of capacitance with temperature (see Table 3) Tangent of loss angle Leakage current (see Table 3) Impedance (if applicable) (see Table 4) Equivalent series resistance (ESR) (if required) (see Table 5) Surge voltage Table 2 Values

29、 of capacitance and of voltage related to case sizes Rated voltage Category voltageaCase size Case size Case size Case size Rated capacitance (in F) aIf different from the rated voltage. 5 EN 60384-3-1:2006BS EN 60384-3-1:2006Table 3 Characteristics at high and low temperature Maximum values Capacit

30、ance change % Tangent of loss angle % Leakage current A URV CRF TATRTBTA20 C TRTB20 C TRTBaTAis the lower category temperature. TBis the upper category temperature. TRis the rated temperature. aMeasured with the category voltage. Table 4 Impedance at 100 kHz (if required) Case size Impedance Table 5

31、 Equivalent series resistance (ESR) at 100 kHZ (if required) Rated voltage URV Rated capacitance F Maximum ESR m 6 EN 60384-3-1:2006BS EN 60384-3-1:20061.4 Normative references IEC 60286-3, Packaging of components for automatic handling Part 3: Packaging of leadless components on continuous tapes IE

32、C 60384-1, Fixed capacitors for use in electronic equipment Part 1: Generic specification IEC 60384-3, Fixed capacitors for use in electronic equipment Part 3: Sectional specification: Fixed surface mount tantalum capacitors IEC 60410, Sampling plans and procedures for inspection by attributes 1.5 M

33、arking The marking of the capacitor (if applied) and the package shall be in accordance with the requirements of IEC 60384-3, 1.6. The details of the marking of the component and package shall be given in full in the detail specification. 1.6 Ordering information Orders for capacitors covered by thi

34、s specification shall contain, in clear or in coded form, the following minimum information: a) rated capacitance; b) tolerance on rated capacitance; c) rated d.c. voltage; d) number and issue reference of the detail specification and style reference; e) packing (bulk or taped; if taped, according t

35、o IEC 60286-3). 1.7 Certified records of released lots Required/not required. 1.8 Additional information (not for inspection purposes) 1.9 Additional or increased severities or requirements to those specified in the generic and/or sectional specification NOTE Additions or increased requirements shou

36、ld be specified only when essential. Table 6 Other characteristics This table is to be used for defining characteristics which are additional to, or more severe than, those given in the sectional specification. 7 EN 60384-3-1:2006BS EN 60384-3-1:20062 Inspection requirements 2.1 Procedures 2.1.1 For

37、 qualification approval, the procedures shall be in accordance with 3.4 of IEC 60384-3. 2.1.2 For quality conformance inspection, the test schedule (Table 7) includes sampling, periodicity, severities and requirements. The formation of inspection lots is covered by 3.5.1 of IEC 60384-3. Table 7 Test

38、 schedule for conformance (lot-by-lot) inspection (Groups A and B) Assessment level EZ Number of specimens and number of non-conforming itemsb Subclause number and testaD or ND Conditions of testaIL ndc Performance requirementsaGroup A inspection (lot-by-lot) Subgroup A0 4.21 High surge current (if

39、required by the detail specification) ND 100 % 4.5.1 Leakage current Protective resistance: 1 000 0,02 CRURA/F V or 1 A, whichever is the greater.See Table 3 for details 4.5.2 Capacitance Frequency: . Hz Bias: . V Within specified tolerance 4.5.3 Tangent of loss angle (tan ) Frequency: Hz Bias: . V

40、Class 1 0,08 Class 2 0,12 Class 3 0,24 See Table 3 for details 4.5.4 Impedance c Frequency: 100 kHz As in Table 4 4.5.5 Equivalent series resistance (ESR) cFrequency: 100 kHz As in Table 5 Subgroup A1 4.4 Visual examination 4.4 Dimension (detail) ND S-3 d)0 As in 4.4.2 Marking legible and as specifi

41、ed in 4.5 of this specification See Table 1 of this specification Group B inspection (lot-by-lot) D S-3 d)0 4.7 SolderabilitydMethod:Temperature and duration:or Temperature profile:.4.7.2 Final measurement Visual examination As in 4.7.2 4.18 Solvent resistance of the marking (if applicable) Solvent:

42、 Solvent temperature: Method 1 Rubbing material: cotton wool Recovery time: Legible marking 8 EN 60384-3-1:2006BS EN 60384-3-1:2006Table 7 (continued) Sample size and criterion of acceptabilitybSubclause number and testaD or ND Conditions of testap n c Performance requirementsaGROUP C INSPECTION (in

43、spection) Subgroup C1 4.6.1 Initial measurements 4.6 Resistance to soldering heat 4.6.3 Final measurements 4.17 Component solvent resistancec(if applicable) D Capacitance Tangent of loss angle Attitude: dCapacitance Tangent of loss angle (tan ) Solvent: dSolvent temperature: dMethod: 2 Recovery: . d

44、Visual examination 3 12 0 |C/C| %d.dTo be specified in the detail specification As in 4.6.3 Subgroup C2 4.9 Substrate bending teste 4.9.6 Final measurement D Capacitance (with printed board in bent position) Deflection: mmdNumber of bends: dVisual examination 3 12 0 |C/C| %dNo visible damage Subgrou

45、p C3 4.3 Mounting D Visual examination Leakage current Capacitance Tangent of loss angle (tan )Impedancecor Equivalent series resistance (ESR)cNo visible damage 0,02 CR URA/F V or 1 A, whichever is the greater To be specified in the detail specification To be specified in the detail specification As

46、 in Table 4 As in Table 5 9 EN 60384-3-1:2006BS EN 60384-3-1:2006Table 7 (continued) Sample size and criterion of acceptabilitybPerformance requirementsaSubclause number and testaD or ND Conditions of testap n c Subgroup C3.1 4.8 Shear test 4.10.1 Initial measurement D Visual examination Not require

47、d (see Group C3) 6 8 0 No visible damage 4.10 Rapid change of temperature 4.10.3 Final measurement 4.11 Climatic sequence(Style 1 only) 4.11.1 Initial measurement 4.11.2 Dry heat 4.11.3 Damp heat, cyclic, test Db, first cycle4.11.4 Cold 4.11.5 Damp heat, cyclic, test Db, remaining cycles TA= Lower c

48、ategory temperature TB= Upper category temperature Five cycles Duration t1= 30 min Recovery: 1 h to 2 h Leakage current Capacitance Tangent of loss angle (tan ) Not required Temperature: upper category temperature Duration: 16 h Temperature: lower category temperature Duration: 2 h Recovery: 1 h to

49、2 h initial limit |C/C| 5 % Style 1 |C/C| 10 % Style 2 of value measured in Group C3 initial limit 4.11.6 Final measurements Visual examination Leakage current Capacitance Tangent of loss angle (tan ) No visible damage Marking legible initial limit |C/C| 10 % of value measured in Group C3 1,2 times initial limit 10 EN 60384-3-1:2006BS EN 60384-3-1:2006Table 7 (continu