EN 60317-0-4-2016 en Specifications for particular types of winding wires - Part 0-4 General requirements - Glass-fibre wound resin or varnish impregnated bare or enamelled rectang.pdf

《EN 60317-0-4-2016 en Specifications for particular types of winding wires - Part 0-4 General requirements - Glass-fibre wound resin or varnish impregnated bare or enamelled rectang.pdf》由会员分享，可在线阅读，更多相关《EN 60317-0-4-2016 en Specifications for particular types of winding wires - Part 0-4 General requirements - Glass-fibre wound resin or varnish impregnated bare or enamelled rectang.pdf（30页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationSpecifications for particular types of winding wiresPart 0-4: General requirements Glass-fibre wound, resin or varnish impregnated, bare or enamelled rectangular copper wireBS EN 60317-0-4:2016National forewordThis British Standard is the UK implementation of EN 60317-0-4:20

2、16. It is identical to IEC 60317-0-4:2015. It supersedes BS EN 60317-0-4:1998 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee L/-/99, Miscellaneous Standards - Electrical.A list of organizations represented on this committee can be obtained onrequest to

3、 its secretary.This publication does not purport to include all the necessary provisions ofa contract. Users are responsible for its correct application. The British Standards Institution 2016.Published by BSI Standards Limited 2016ISBN 978 0 580 85660 0ICS 29.060.10Compliance with a British Standar

4、d cannot confer immunity fromlegal obligations.T h i s B r i t i s h S t a n d a r d w a s p u b l i s h e d u n d e r t h e a u t h o r i t y o f t h eS t a n d a r d s P o l i c y a n d S t r a t e g y C o m m i t t e e o n 31 January 2 0 1 6 .Amendments/corrigenda issued since publicationDate Tex

5、t affectedBRITISH STANDARDBS EN 60317-0-4:2016EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 60317-0-4 January 2016 ICS 29.060.10 Supersedes EN 60317-0-4:1998 English Version Specifications for particular types of winding wires - Part 0-4: General requirements - Glass-fibre wound, resin or var

6、nish impregnated, bare or enamelled rectangular copper wire (IEC 60317-0-4:2015) Spcifications pour types particuliers de fils de bobinage - Partie 0-4: Exigences gnrales - Fil de section rectangulaire en cuivre nu ou maill, guip de fibres de verre imprgnes de vernis ou de rsine (IEC 60317-0-4:2015)

7、 Technische Lieferbedingungen fr bestimmte Typen von Wickeldrhten - Teil 0-4: Allgemeine Anforderungen - Flachdrhte aus Kupfer, blank oder lackisoliert und umhllt mit Glasgewebe, imprgniert mit Harz oder Lack (IEC 60317-0-4:2015) This European Standard was approved by CENELEC on 2015-11-27. CENELEC

8、members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on appli

9、cation to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CEN

10、ELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Ic

11、eland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Euro

12、pisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members. Ref. No. EN 60317-0-4:2016 E BS EN 60317-0-4:2016EN 60317-0-4:2016 2 European for

13、eword The text of document 55/1550/FDIS, future edition 3 of IEC 60317-0-4, prepared by IEC/TC 55 “Winding wires“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 60317-0-4:2016. The following dates are fixed: latest date by which the document has to be implemented at nat

14、ional level by publication of an identical national standard or by endorsement (dop) 2016-08-27 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2018-11-27 This document supersedes EN 60317-0-4:1998. Attention is drawn to the possibility that some

15、of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 60317-0-4:2015 was approved by CENELEC as a European Standard without an

16、y modification. In the official version, for Bibliography, the following notes have to be added for the standards indicated: IEC 60264 NOTE Harmonized in EN 60264 series. IEC 60317 NOTE Harmonized in EN 60317 series. BS EN 60317-0-4:2016EN 60317-0-4:2016 3 Annex ZA (normative) Normative references t

17、o international publications with their corresponding European publications The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest ed

18、ition of the referenced document (including any amendments) applies. NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex

19、 is available here: www.cenelec.eu. Publication Year Title EN/HD Year IEC 60851 series Winding wires - Test methods EN 60851 series BS EN 60317-0-4:2016 2 IEC 60317-0-4:2015 IEC 2015 CONTENTS FOREWORD . 4 INTRODUCTION . 6 1 Scope 7 2 Normative references 7 3 Terms, definitions and general notes on t

20、ests and appearance 7 3.1 Terms and definitions 7 3.2 General notes . 8 3.2.1 Methods of test 8 3.2.2 Winding wire 8 3.3 Appearance 9 4 Dimensions 9 4.1 Conductor dimensions 9 4.2 Tolerance on conductor dimensions 11 4.3 Rounding of corners 11 4.4 Increase in dimensions due to the insulation . 11 4.

21、5 Overall dimensions . 13 4.5.1 Nominal overall dimensions . 13 4.5.2 Minimum overall dimensions 13 4.5.3 Maximum overall dimensions . 13 5 Electrical resistance 13 6 Elongation . 13 7 Springiness . 13 8 Flexibility and adherence . 14 8.1 Mandrel winding test . 14 8.2 Adherence test 14 8.2.1 Glass-f

22、ibre covered bare wires 14 8.2.2 Glass-fibre covered enamelled wires . 14 9 Heat shock 14 10 Cut-through . 14 11 Resistance to abrasion 14 12 Resistance to solvents . 14 13 Breakdown voltage 14 14 Continuity of insulation 15 15 Temperature index 15 16 Resistance to refrigerants 15 17 Solderability 1

23、5 18 Heat or solvent bonding . 15 19 Dielectric dissipation factor 15 20 Resistance to transformer oil . 15 21 Loss of mass . 15 23 Pin hole test 16 30 Packaging . 16 BS EN 60317-0-4:2016IEC 60317-0-4:2015 IEC 2015 3 Annex A (informative) Nominal cross-sectional areas for preferred and intermediate

24、sizes . 17 Bibliography 24 Table 1 Nominal cross-sectional areas of preferred sizes . 10 Table 2 Conductor tolerances 11 Table 3 Corner radii . 11 Table 4 Increase in dimensions 12 Table 5 Elongation . 13 Table 6 Mandrel winding 14 Table 7 Breakdown voltage 15 Table A.1 Nominal cross-sectional areas

25、 (1 of 7) . 17 BS EN 60317-0-4:2016 4 IEC 60317-0-4:2015 IEC 2015 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES Part 0-4: General requirements Glass-fibre wound, resin or varnish impregnated, bare or enamelled rectangular copper wire FOREWORD 1) The

26、 International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and

27、 electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical com

28、mittees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization f

29、or Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committe

30、e has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is ac

31、curate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regi

32、onal publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in

33、 some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agen

34、ts including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of,

35、or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some o

36、f the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60317-0-4 has been prepared by IEC technical committee 55: Winding wires. This third edition cancels and replaces th

37、e second edition published in 1997, Amendment 1:1999 and Amendment 2:2005. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) addition of dimensional requirements for grade 1 enamelled wire in Tabl

38、e 4; b) addition of dielectric breakdown requirements for grade 1 enamelled wire in Table 7. BS EN 60317-0-4:2016IEC 60317-0-4:2015 IEC 2015 5 The text of this standard is based on the following documents: FDIS Report on voting 55/1550/FDIS 55/1565/RVD Full information on the voting for the approval

39、 of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all the parts in the IEC 60317 series, published under the general title Specifications for particular types of winding

40、wires, can be found on the IEC website. This standard is to be read in conjunction with the IEC 60851 series. The clause numbers used in this standard are identical with the respective test numbers of the IEC 60851 series. In case of inconsistencies between IEC 60851 and this standard, the latter pr

41、evails. The numbering of clauses in this standard is not continuous from Clauses 21 through 30 in order to reserve space for possible future wire requirements prior to those for wire packaging. The committee has decided that the contents of this publication will remain unchanged until the stability

42、date indicated on the IEC website under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. BS EN 60317-0-4:2016 6 IEC 60317-0-4:2015 IEC 2015 INTRODUCTION This part of IEC 6

43、0317 is one of a series which deals with insulated wires used for windings in electrical equipment. The series has three groups describing: 1) Winding wires Test methods (IEC 60851); 2) Specifications for particular types of winding wires (IEC 60317); 3) Packaging of winding wires (IEC 60264). BS EN

44、 60317-0-4:2016IEC 60317-0-4:2015 IEC 2015 7 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES Part 0-4: General requirements Glass-fibre wound, resin or varnish impregnated, bare or enamelled rectangular copper wire 1 Scope This part of IEC 60317 specifies general requirements of glass-fibre wou

45、nd, resin or varnish impregnated, bare or enamelled rectangular copper wire. The range of nominal conductor dimensions is given in the relevant specification sheet. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable

46、for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60851 (all parts), Winding wires Test methods 3 Terms, definitions and general notes on tests and appearance 3.1 Te

47、rms and definitions For the purposes of this document, the following terms and definitions apply. 3.1.1 coating material which is deposited on a conductor or wire by a suitable means and then dried and/or cured 3.1.2 conductor bare metal after removal of the insulation 3.1.3 covering material which

48、is wound, wrapped or braided around a bare or insulated conductor 3.1.4 crack opening in the insulation which exposes the conductor to view at the stated magnification 3.1.5 enamelled wire wire coated with an insulation of cured resin 3.1.6 grade range of thickness of the insulation of a wire BS EN

49、60317-0-4:2016 8 IEC 60317-0-4:2015 IEC 2015 3.1.7 insulation coating or covering on the conductor with the specific function of withstanding voltage 3.1.8 nominal conductor dimension designation of the conductor size in accordance with IEC 60317 3.1.9 normal vision 20/20 vision, with corrective lenses if necessary 3.1.10 winding wire wire used for winding a coil to provide a magnetic field 3.1.11 wire conductor coated or covered with an insulation 3.2 General note